含点蚀损伤船体加筋板在纵向压力下的极限强度

针对老龄化船舶结构上的点状腐蚀,利用非线性有限元方法进行计算,分析304个船体加筋板的极限强度,探讨带板柔度、加强筋柔度、腐蚀面积比和腐蚀深度比对纵向压力下含点蚀损伤船体加筋板极限强度的影响,拟合出点状腐蚀下船体加筋板极限强度折减公式并对其适用性进行验证,研究结果具有一定的工程参考意义和价值。     

点蚀损伤板在复杂受力状态下的极限强度研究

采用非线性有限元软件模拟船底板单面点腐蚀,通过对边缘载荷系数比、蚀坑分布、直径、深度的改变,经过一系列的数值计算分析,结果表明横向载荷和侧压对板的极限强度影响不可忽略,计算板的极限承载能力时需要考虑计及侧压与横向载荷。在复杂受力状态下,就单考虑蚀坑深度时,板表面的蚀坑深度在0~0.5t区间变化时,极限强度相应的折减率比大于1/2板厚时更大,极限强度对蚀坑深度更加敏感。腐蚀面积不能有效表征腐蚀程度,当DOP系数相同时,点蚀后板的最小横截面决定了极限强度的大小。     

极地低温和凹陷损伤下加筋板极限强度的参数敏感性分析

为了快速评估含船冰碰撞凹陷损伤下加筋板在轴向压缩载荷作用下的极限强度，本文采用非线性有限元法对低温凹陷损伤加筋板的极限强度进行研究。根据EH36钢在低温下的材料力学性能试验，通过折减因子评估法，基于完整加筋板在轴向压缩下极限强度的经验公式，提出以加筋板柔度和加筋板壳板柔度为变化参数，采用最小二乘法拟合折减系数，得到低温含凹陷损伤加筋板剩余极限强度的经验公式。结果表明，相比于凹陷长度和凹陷深度，凹陷宽度对加筋板极限强度的影响较大；对比分析凹陷损伤加筋板极限强度的经验公式和有限元法的计算结果，误差较小，验证了船冰碰撞凹陷损伤下加筋板的极限强度快速评估方法的准确性。     

单点腐蚀船体板剩余疲劳寿命的数值计算

船体板在波浪载荷下会受到交变拉/压作用,因此必须考虑疲劳对船体板剩余寿命的影响,尤其是对含点腐蚀船体板剩余寿命的影响。本文对单点腐蚀船体板剩余疲劳寿命进行了数值计算,结果表明:使用二次单元对含蚀坑船体板应力集中系数的计算误差不超过10%,而使用线性单元误差可达40%;蚀坑直径对单点腐蚀船体板疲劳寿命的影响不大,而船体板剩余疲劳寿命随蚀坑深度的增大而迅速减小。可见,对于点腐蚀钢板的应力集中计算,使用而二次单元比使用线性单元更准确;蚀坑深度对单点腐蚀船体板剩余疲劳寿命的影响比蚀坑直径的影响更为显著。     

轴向压力下含点蚀损伤加筋板极限强度研究

点蚀损伤常发生于船体结构,将会造成结构的局部缺失而影响船舶结构的安全性.针对船体结构的基本构件加筋板,采用非线性有限元法研究轴向压力下点蚀损伤对其极限强度的影响,考虑点蚀位置、直径、数目、深度、点蚀损失体积等影响因素,分析船体加筋板极限应力和屈曲失效模式,获得结构的极限强度,拟合影响因素和加筋板极限强度的关系曲线,定性分析了点蚀损伤对加筋板的破坏.结果表明,点蚀损伤削减了加筋板极限强度;点蚀影响因素(点蚀直径、数目、深度、损失体积)对含点蚀损伤加筋板极限强度的影响近似呈现非线性的二次单调函数关系.     

点蚀损伤船体结构板的极限剪切屈曲强度研究

腐蚀损伤导致船体结构板的极限承载能力大幅度下降。文章采用腐蚀体积描述板的点蚀损伤程度,模拟船体结构板的点蚀损伤形态,在点蚀损伤板模型中变化板的厚度、点蚀数目、点蚀直径以及点蚀分布等要素,实施系列有限元数值模拟计算,在进行理论分析的基础上,采用统计学方法,建立了点蚀损伤板极限剪切屈曲强度的评估方法,得到了点蚀损伤板极限剪切屈曲强度的计算公式。从而确立了基于腐蚀体积的点蚀损伤船体结构板极限剪切屈曲强度的评价技术,可为在役海船点蚀损伤后的安全性评估提供有效的技术手段。     

点蚀损伤下纵向受压船体加筋板极限强度计算

基于实船点蚀损伤勘验数据,通过有限元数值计算法分析了点蚀分布、深度和面积等点蚀特征参数对船体加筋板极限强度的影响规律,给出了以点蚀深度和点蚀面积双参数的点蚀加筋板极限强度公式。结果表明:在点蚀不穿孔且点蚀面积低于10%条件下,当点蚀面积和点蚀深度一定时,蚀点分布造成的船体加筋板极限强度最大波动值低于2%;点蚀面积和点蚀深度对加筋板极限强度的影响是交互非独立的;基于点蚀面积、深度给出的双参数加筋板极限强度计算公式计算精度较高,满足工程需要。     

双轴压缩工况下点蚀参数对加筋板极限强度影响规律

考虑到在双轴压应力状态下,点蚀对船体板、加筋板的极限强度影响规律尚不明确,对3种典型的船体加筋板采用有限元法计算分析双轴压缩工况下点蚀特征参数(分布、密度、深度,以及半径)对加筋板极限强度的影响规律,结果表明,点蚀分布对加筋板极限强度影响较小;点蚀密度对极限强度的影响与点蚀面积有关;在蚀点总体积一定的条件下,点蚀深度和半径对加筋板极限强度的影响甚微,蚀点总体积是衡量点蚀加筋板极限强度较为合理的参数。     

考虑点腐蚀影响的船体板疲劳寿命评估

针对疲劳现象对点腐蚀极为敏感的问题,基于点腐蚀蚀坑处的应力集中系数,计算了含点腐蚀船体板单元的疲劳寿命。结果发现:对于半球形蚀坑,蚀坑处应力集中系数随蚀坑深度的增加而增大,两者基本上呈线性关系;当蚀坑深度为0,即无点腐蚀时,累积损伤度约为1,结构的疲劳寿命约等于设计寿命,这与客观事实是相符的,验证了基于应力集中系数计算结构疲劳寿命的合理性;当蚀坑深度仅为0. 2倍板厚时,含2种蚀坑的板单元疲劳寿命迅速减小到原寿命的47%、9%和23%;当蚀坑深度达到板厚时,板单元被蚀穿。这一结果说明结构的疲劳寿命随蚀坑深度的增大急剧减小,结构的疲劳寿命对点腐蚀极为敏感。     

点蚀、裂纹损伤对船用加筋板剩余极限强度的影响

[目的]长期服役于恶劣海洋环境中的船舶与海洋工程结构,不可避免地会产生裂纹和点蚀,这些损伤会对结构的极限承载能力产生较大影响。为探讨裂纹、点蚀同时存在时对结构承载能力的影响,[方法]采用非线性有限元法开展含裂纹、点蚀损伤的加筋板在轴向压载作用下的极限强度研究。在讨论网格尺寸对含裂纹、点蚀损伤加筋板极限强度影响的基础上,开展裂纹点蚀坑相对位置、点蚀数目、裂纹长度对含裂纹、点蚀损伤加筋板剩余极限强度的影响。[结果]计算结果表明,裂纹长度、点蚀的增加会使加筋板的剩余极限强度下降明显。[结论]这些结果可用于指导全寿期船舶与海洋工程结构的设计与维护。     

Computation of ultimate strength of locally corroded unstiffened plates under uniaxial compression

Over the past decades there have been many losses of the merchant vessels due to either accidents or exposure to large environmentally induced forces. The potential for the structural capability-degrading effects of both corrosion and fatigue induced cracks are of profound importance and must be both fully understood and reflected in vessel's inspection and maintenance programme. The present study is focused on assessing the effects of localized pitting corrosion which concentrates at one or several possibly large area on the ultimate strength of unstiffened plates. Over 256 nonlinear finite element analyses (FEA) of panels with various locations and sizes of pitting corrosion have been carried out. The multi-variable regression method is applied to derive new formulae to predict ultimate strength of unstiffened plates with localized corrosion. The results indicate that the length, breadth and depth of pit corrosion have weakening effects on the ultimate strength of the plates while plate slenderness has only marginal effect on strength reduction. Transverse location of pit corrosion is also an important factor determining the amount of strength reduction. When corrosion spreads transversely on both edges, it has the most deteriorating effect on strength. It was also found out that the proposed formulae can accurately predict the ultimate strength of unstiffened plate with localized corrosion.     

Experimental and numerical study of localized pitting effect on compressive behavior of tubular members

Locally pitted tubular members are usually considered as stub columns to assess the ultimate strength. However, it is not suitable for those with relatively larger slenderness ratios as their failure behavior is more complex and closely related to corrosion features of localized pitting. This paper presents compressive column tests on locally pitted tubular members of a moderate slenderness ratio. Corrosion pits were artificially introduced on local surface of the members, forming corrosion patches with various corrosion features. A numerical modelling method was proposed to reproduce the test specimens. Localized pitting damage was proven to cause substantial declines in the load deformation capacity and ultimate strength, and have a significant effect on the failure mode. The failure of a pitted member is mostly initiated by local buckling after yielding occurs in the corrosion patch, concurrent with pitting closure, and even shear cracking of member wall due to the perforated pits. Moreover, shape change of the corrosion patch most likely results in the failure mode to alter from column buckling to local buckling or interactive buckling. The shape ratio of the corrosion patch is one of the critical factor to influence the ultimate strength of locally pitted members. The proposed modelling method is applicable for extensive stochastic simulations so as to develop an empirical formula and to clarify the probabilistic characteristics of ultimate strength.     

Compressive strength of tubular members with localized pitting damage considering variation of corrosion features

Localized pitting corrosion often occurs on marine and offshore structures in the form of patch corrosion with great uncertainties in the location, size and shape. The variation of corrosion features affects ultimate strength of tubular members significantly, but it is still not well understood. This paper presents a numerical study on tubular members of diverse slenderness ratios to clarify the localized pitting effect on ultimate strength. Numerical analyses were performed based on novel models of pitted members that were calibrated against benchmark column tests. Corrosion pits were randomly introduced on the local outside surfaces of members via stochastic simulation, forming corrosion patches varied in the location, size and shape. Numerical results obtained were regressed to propose a unified empirical formula to predict ultimate strength. It turned out that the shape of the corrosion patch has a significant influence on the ultimate strength. The shape change of the patch can alter failure modes of medium length columns. The reduction of ultimate strength is closely related to the shape ratio of the patch besides the volume loss of corroded material. The unified empirical formula incorporating the shape ratio and the volume loss shows a good ability to predict the experimental results.     

点蚀损耗对船体梁极限强度的影响（英文）

The paper focuses on the assessment of the hull girder ultimate strength,combined with random pitting corrosion wastage,by the incremental-iterative method.After a brief review about the state of art,the local ultimate strength of pitted platings under uniaxial compression is preliminarily outlined and subsequently a closed-form design formula is endorsed in the Rule incremental-iterative method,to account for pitting corrosion wastage in the hull girder ultimate strength check.The ISSC bulk carrier is assumed as reference ship in a benchmark study,devoted to test the effectiveness of the incremental-iterative method,by a comparative analysis with a set of FE simulations,performed by Ansys Mechanical APDL.Four reference cases,with different locations of pitting corrosion wastage,are investigated focusing on nine combinations of pitting and corrosion intensity degrees.Finally,a comparative analysis between the hull girder ultimate strength,combined with pitting corrosion wastage,and the relevant values,complying with the Rule net scantling approach,is performed.Based on current results,the modified incremental-iterative method allows efficiently assessing the hull girder ultimate strength,combined with pitting corrosion wastage,so revealing useful both in the design process of new vessels and in the structural health monitoring of aged ships.     

CFRP修复的FPSO点蚀船体梁极限强度分析

采用非线性有限元法对中拱和中垂工况条件下碳纤维增强聚合物(Carbon Fiber Reinforced Polymer, CFRP)修复的浮式生产储卸油装置(Floating Production Storage and Offloading, FPSO)点蚀船体梁极限强度进行仿真分析。对比FPSO的完整船体梁、点蚀船体梁和CFRP修复的点蚀船体梁的中拱极限弯矩和中垂极限弯矩，分析CFRP对FPSO点蚀船体梁的修复效果，并分析胶层失效规律。结果表明，CFRP可为船舶的高效修复提供一种新的方式。     

Effect of pitting corrosion on local strength of hold frames of bulk carriers (2nd Report)—Lateral-distortional buckling and local face buckling

Pitting corrosion is typical corrosion observed on coated hold frames of bulk carriers which exclusively carry coal and iron ore. In order to secure the safety of these types of bulk carriers, it is important to understand the effect of pitting corrosion on local strength of hold frames.

In order to investigate this effect, a series of 4- and 3-point bend tests on structural models which consist of web, shell and face plates has been carried out. Artificial pitting was created on the web plate to simulate pitting. In the 4-point bend tests, two equal concentrated loads have been applied vertically at the one-third points of simply supported models so that compression load due to bending would act on the face plate. In this testing condition, lateral-distortional buckling occurred before reaching the ultimate strength and local buckling of the face plate was observed after reaching the ultimate strength. The effect of web plate pitting on the lateral-distortional buckling strength was found to be small but the ultimate strength decreases with increase in the degree of pitting intensity. In the 3-point bend tests, concentrated load has been applied vertically at the center of simply supported models so that compression load due to bending would act on the face plate. In this testing condition, local face buckling occurred just after reaching the ultimate strength. The ultimate strength is found to be decreasing with increase in the degree of pitting intensity.

A series of non-linear FE analyses has been performed to simulate the deformation behavior observed in the tests. It has been revealed that even in the case of randomly distributed pitting corrosion the ultimate strength of the structural models was almost the same as that of the structural models with uniform corrosion corresponding to the average thickness loss.     

Effect of pitting corrosion on the ultimate strength of steel plates subjected to in-plane compression and bending

Corrosion pits with a circular cone shape are typically observed on coated hold frames of aged bulk carriers which carry exclusively coal and iron ore. In order to ensure the safety of these types of bulk carrier, it is necessary to understand the effect of pitting corrosion on the local strength of hold frames. In order to investigate this effect, a series of nonlinear finite-element (FE) analyses has been performed with pitted plates subjected to in-plane compressive loads and bending moments. It has been shown that the ultimate compression load or bending moment of pitted plates is smaller than that of uniformly corroded plates in terms of average thickness loss, and that predictions of the ultimate strength using the average thickness loss at the minimum cross section would be conservative. In order to establish a method of evaluating strength reduction due to pitting corrosion, it is important to identify the failure mode that would be most detrimentally affected by pitting corrosion. It was found that the reduction of the ultimate compressive load or bending moment due to pitting corrosion is smaller than that of the tensile strength in terms of equivalent thickness.     

考虑腐蚀影响的船舶结构可靠性研究现状与展望

对近年来考虑腐蚀影响的船舶结构可靠性计算各主要研究层面的研究现状做了介绍与评述.通过这一综述可以发现:此领域研究工作重心已由考虑线性、非线性均匀腐蚀的影响逐步向局部腐蚀尤其是点腐蚀方向转变.今后的研究重点为以下三个方面,即:①发展符合基本腐蚀机理、与实测腐蚀数据较为吻合的点腐蚀多指标模型;②确定蚀点几何参数在各类荷载条件下对构件强度的影响;③深入评估腐蚀与疲劳的相互作用对结构可靠性计算的影响.     

Ultimate strength assessment of simply supported pitted platings: A new stochastic approach based on Monte Carlo simulation

The ultimate strength assessment of platings affected by random corrosion wastage is a key factor for the reliable design of new ships and the structural health monitoring of aged structures, as pitting corrosion wastage significantly affects the ultimate capacity of platings under compression. In this respect, significant efforts have been undertaken in the last decade to assess the ultimate strength drop-off of pitted platings under compression and several interpolating design formulas, based on a large number of FE simulations, have been developed. Nevertheless, current Rules and guidelines don't provide any explicit strength check criterion for pitted platings. Hence, the main aim of current research is the development of a new framework for the ultimate strength assessment of pitted platings, based on a stochastic approach and the endorsement of Monte Carlo simulation. A new formula, which allows evaluating the statistical properties of the plating ultimate strength in presence of random corrosion wastage, is developed. Subsequently, a benchmark study is carried out, to compare the new formula with the existing ones available in literature and a wide set of FE simulations, carried out by Ansys APDL. Current results are discussed, and the effectiveness of the new formula is verified.