Stochastic eco-routing in a signalized traffic network

In this paper, an eco-routing algorithm is developed for vehicles in a signalized traffic network. The proposed method incorporates a microscopic vehicle emission model into a Markov decision process (MDP). Instead of using GPS-based vehicle trajectory data, which are used by many existing eco-routing algorithm, high resolution traffic data including vehicle arrival and signal status information are used as primary inputs. The proposed method can work with any microscopic vehicle model that uses vehicle trajectories as inputs and gives related emission rates as outputs. Furthermore, a constrained eco-routing problem is proposed to deal with the situation where multiple costs present. This is done by transferring the original MDP based formulation to a linear programming formulation. Besides the primary cost, additional costs are considered as constraints. Two numerical examples are given using the field data obtained from City of Pasadena, California, USA. The eco-routing algorithm for single objective is compared against the traditional shortest path algorithm, Dijkstra’s algorithm. Average reductions of CO emission around 20% are observed.     

Estimation of saturation flow at signalised intersections of developing cities: a micro-simulation modelling approach

Traffic characteristics and operations at the signalised intersections of developing cities are significantly different from those at the similar intersections of cities in developed countries. Considering this, a new microscopic simulation technique, where a co-ordinate approach to modelling vehicle location is adopted, has been used for modelling the traffic operations at signalised intersections of developing cities. The model has been calibrated and validated on the basis of data collected from Dhaka, the capital of Bangladesh. It has been found that the concept of passenger car unit (PCU), which is widely used as a signal design parameter, is not applicable in case of mixed traffic comprising of both motorised and non-motorised vehicles. Therefore, using the developed simulation model the saturation flows at signalised intersections are investigated in an aggregate form of vehicles per hour. It has also been found that saturation flows in terms of aggregate vehicles are very much dependent on the approach width, turning proportion and composition of the traffic mix. Using the simulation results, an equation has also been regressed in order to be able to estimate the saturation flow from the influencing variables like road width, turning proportion, percentage of heavy and non-motorised vehicles.     

A field evaluation case study of the environmental and energy impacts of traffic calming

This study quantifies the energy and environmental impact of a selection of traffic calming measures using a combination of second-by-second floating-car global positioning system data and microscopic energy and emission models. It finds that traffic calming may result in negative impacts on vehicle fuel consumption and emission rates if drivers exert aggressive acceleration levels to speed up to their journeys. Consequently by eliminating sharp acceleration maneuvers significant savings in vehicle fuel consumption and emission rates are achievable through driver education. The study also demonstrates that high emitting vehicles produce CO emissions that are up to 25 times higher than normal vehicle emission levels while low emitting vehicles produce emissions that are 15–35% of normal vehicles. The relative increases in vehicle fuel consumption and emission levels associated with the sample traffic calming measures are consistent and similar for normal, low, and high emitting vehicles.     

Noise prediction for highways in Thailand

A model of highway traffic noise is formulated based on vehicle types. The data were collected from local highways in Thailand with free-flow traffic conditions. First, data on vehicle noise was collected from individual vehicles using sound level meters placed at a reference distance. Simultaneously, measurements were made of vehicles’ spot speeds. Secondly, are data for building the highway traffic noise model. This consists of traffic noise levels, traffic volumes by vehicle classification, average spot speeds by vehicle type, and the geometric dimension of highway sections. The free-flow traffic noise model is generated from this database. A reference energy mean emission level (the basic noise) level for each type of vehicles is developed based on direct measurement of Leq (10 s) from the real running condition of each type of vehicles. Modification of terms and parameters are used to make the model fit highway traffic characteristics and different types of vehicle.     

Estimating fuel consumption and emissions based on reconstructed vehicle trajectories

Microscopic emission models are widely used in emission estimation and environment evaluation. Traditionally, microscopic traffic simulation models and probe vehicles are two sources of inputs to a microscopic emission model. However, they are not effective in reflecting all vehicles' real‐world operating conditions. Using each vehicle's spot speed data recorded by detectors, this paper provides a new method to estimate all vehicles' real‐world activities data. These data can then be used as inputs to a microscopic emission model to estimate vehicle fuel consumption and emissions. The main task is to reconstruct trajectory of each vehicle and calculate second‐by‐second speed and acceleration from the activities data. The Next Generation Simulation dataset and the Comprehensive Modal Emissions Model are used in this study to calculate and analyze the emission results for both lane‐level and link‐level. The results showed that using the proposed method for estimating vehicle fuel consumption and emissions is promising. Copyright © 2012 John Wiley & Sons, Ltd.     

A mesoscopic integrated urban traffic flow-emission model

Due to the noticeable environmental and economical problems caused by traffic congestion and by the emissions produced by traffic, analysis and control of traffic is essential. One of the various traffic analysis approaches is the model-based approach, where a mathematical model of the traffic system is developed/used based on the governing physical rules of the system. In this paper, we propose a framework to interface and integrate macroscopic flow models and microscopic emission models. As a result, a new mesoscopic integrated flow-emission model is obtained that provides a balanced trade-off between high accuracy and low computation time. The proposed approach considers an aggregated behavior for different groups of vehicles (mesoscopic) instead of considering the behavior of individual vehicles (microscopic) or the entire group of vehicles (macroscopic). A case study is done to evaluate the proposed framework, considering the performance of the resulting mesoscopic integrated flow-emission model. The traffic simulation software SUMO combined with the microscopic emission model VT-micro is used as the comparison platform. The results of the case study prove that the proposed approach provides excellent results with high accuracy levels. In addition, the mesoscopic nature of the integrated flow-emission model guarantees a low CPU time, which makes the proposed framework suitable for real-time model-based applications.     

Development of simulated driving cycles for light,medium, and heavy duty trucks: Case of the Toronto Waterfront Area

Driving cycles are an important input for state-of-the-art vehicle emission models. Development of a driving cycle requires second-by-second vehicle speed for a representative set of vehicles. Current standard driving cycles cannot reflect or forecast changes in traffic conditions. This paper introduces a method to develop representative driving cycles using simulated data from a calibrated microscopic traffic simulation model of the Toronto Waterfront Area. The simulation model is calibrated to reflect road counts, link speeds, and accelerations using a multi-objective genetic algorithm. The simulation is validated by comparing simulated vs. observed passenger freeway cycles. The simulation method is applied to develop AM peak hour driving cycles for light, medium and heavy duty trucks. The demonstration reveals differences in speed, acceleration, and driver aggressiveness between driving cycles for different vehicle types. These driving cycles are compared against a range of available driving cycles, showing different traffic conditions and driving behaviors, and suggesting a need for city-specific driving cycles. Emissions from the simulated driving cycles are also compared with EPA’s Heavy Duty Urban Dynamometer Driving Schedule showing higher emission factors for the Toronto Waterfront cycles.     

Exploring the effects of cooperative adaptive cruise control on highway traffic flow using microscopic traffic simulation

This paper examines the impact of having cooperative adaptive cruise control (CACC) embedded vehicles on traffic flow characteristics of a multilane highway system. The study identifies how CACC vehicles affect the dynamics of traffic flow on a complex network and reduce traffic congestion resulting from the acceleration/deceleration of the operating vehicles. An agent-based microscopic traffic simulation model (Flexible Agent-based Simulator of Traffic) is designed specifically to examine the impact of these intelligent vehicles on traffic flow. The flow rate of cars, the travel time spent, and other metrics indicating the evolution of traffic congestion throughout the lifecycle of the model are analyzed. Different CACC penetration levels are studied. The results indicate a better traffic flow performance and higher capacity in the case of CACC penetration compared to the scenario without CACC-embedded vehicles.     

Estimating link travel time functions for heterogeneous traffic flows on freeways

Oversized vehicles, such as trucks, significantly contribute to traffic delays on freeways. Heterogeneous traffic populations, that is, those consisting of multiple vehicles types, can exhibit more complicated travel behaviors in the operating speed and performance, depending on the traffic volume as well as the proportions of vehicle types. In order to estimate the component travel time functions for heterogeneous traffic flows on a freeway, this study develops a microscopic traffic‐simulation based four‐step method. A piecewise continuous function is proposed for each vehicle type and its parameters are estimated using the traffic data generated by a microscopic traffic simulation model. The illustrated experiments based on VISSIM model indicate that (i) in addition to traffic volume, traffic composition has significant influence on the travel time of vehicles and (ii) the respective estimations for travel time of heterogeneous flows could greatly improve their estimation accuracy. Copyright © 2016 John Wiley & Sons, Ltd.     

Network effects of intelligent speed adaptation systems

Intelligent Speed Adaptation (ISA) systems use in-vehicle electronic devices to enable the speed of vehicles to be regulated automatically. They are increasingly appreciated as a flexible method for speed management and control particularly in urban areas. On-road trials using a small numbers of ISA equipped vehicles have been carried out in Sweden, the Netherlands, Spain and the UK. This paper describes the developments made to enhance a traffic microsimulation model in order to represent ISA implemented across a network and the impact of this on the networks. The simulation modelling of the control system is carried out on a real-world urban network, and the impacts on traffic congestion, speed distribution and the environment assessed. The results show that ISA systems are more effective in less congested traffic conditions. Momentary high speeds in traffic are effectively suppressed, resulting in a reduction in speed variation which is likely to have a beneficial impact on safety. Whilst ISA reduces excessive traffic speeds in the network, it does not affect average journey times. In particular, the total vehicle-hours travelling at speeds below 10 km/hr have not changed, indicating that the speed control had not induced more slow-moving queues to the network. A statistically significant, eight percent, reduction in fuel consumption was found with full ISA penetration. These results are in accordance with those from field trials and they provide the basis for cost-benefit analyses on introducing ISA into the vehicle fleet. However, contrary to earlier findings from the Swedish ISA road trials, this study suggested that ISA is likely to have no significant effect on emission of gaseous pollutants CO, NO_x and HC.     

Does traffic-related calibration of car-following models provide accurate estimations of vehicle emissions?

Fuel consumption or pollutant emissions can be assessed by coupling a microscopic traffic flow model with an instantaneous emission model. Traffic models are usually calibrated using goodness of fit indicators related to the traffic behavior. Thus, this paper investigates how such a calibration influences the accuracy of fuel consumption and NOx and PM estimations. Two traffic models are investigated: Newell and Gipps. It appears that the Gipps model provides the closest simulated trajectories when compared to real ones. Interestingly, a reverse ranking is observed for fuel consumption, NOx and PM emissions. For both models, the emissions of single vehicles are very sensitive to the calibration. This is confirmed by a global sensitivity analysis of the Gipps model that shows that non-optimal parameters significantly increase the variance of the outputs. Fortunately, this is no longer the case when emissions are calculated for a group of many vehicles. Indeed, the mean errors for platoons are close to 10% for the Gipps model and always lower than 4% for the Newell model. Another interesting property is that optimal parameters for each vehicle can be replaced by the mean values with no discrepancy for the Newell model and low discrepancies for the Gipps model when calculating the different emission outputs. Finally, this study presents preliminary results that show that multi-objective calibration methods are certainly the best direction for future works on the Gipps model. Indeed, the accuracy of vehicle emissions can be highly improved with negligible counterparts on the traffic model accuracy.     

Study on road section environmental traffic capacity model and algorithm under double constraints

The coordinated development of city traffic and environment is a key research content in traffic field in twenty-first Century. Among them, road section environmental traffic capacity analysis is one of the important research issues. It can provide solid theoretical basis and reliable data support for road network traffic optimization control, road traffic pollution control and city traffic structure optimization. This paper analyzed main factors which impacted environmental traffic capacity from two aspects, including road capacity constraint conditions and road traffic pollution control constraint conditions. Then, road section environmental traffic capacity optimization model was established, and method of improved augmented Lagrange function was used to solve the model. Case study showed that, (1) The environmental traffic capacity optimal model and methodology were effective; (2) In order to ensure road section environmental traffic capacity greater than (or equal to) road capacity, some measures could be taken including adjusting motor vehicle type proportion as well as improving emission characteristics of motor vehicles exhausting pollutants.     

Driving behaviour at motorway ramps and weaving segments based on empirical trajectory data

In the vicinity of ramps, drivers make route choices, change lanes and in most cases also adjust their speeds. This can trigger anticipatory behaviour by the surrounding vehicles, which are also reflected in lane changes and/or changes in speed. This phenomenon is called turbulence and is widely recognised by the scientific literature and various design guidelines. However the knowledge about the characteristics of turbulence is limited. This study investigates the microscopic characteristics of driving behaviour around 14 different on-ramps (3), off-ramps (3) and weaving segments (8) in The Netherlands, based on unique empirical trajectory data collected from a video camera mounted underneath a hovering helicopter. The data analysis reveals that lane changes caused by merging and diverging vehicles create most turbulence, that an increase in the amount of traffic results in a higher level of turbulence and that an increase in the available length for merging and diverging results in a lower level of turbulence. The results of this study are useful for improving the road design guidelines and for modelling driving behaviour more realistically.     

Distributed MPC for cooperative highway driving and energy-economy validation via microscopic simulations

Traffic congestion and energy issues have set a high bar for current ground transportation systems. With advances in vehicular communication technologies, collaborations of connected vehicles have becoming a fundamental block to build automated highway transportation systems of high efficiency. This paper presents a distributed optimal control scheme that takes into account macroscopic traffic management and microscopic vehicle dynamics to achieve efficiently cooperative highway driving. Critical traffic information beyond the scope of human perception is obtained from connected vehicles downstream to establish necessary traffic management mitigating congestion. With backpropagating traffic management advice, a connected vehicle having an adjustment intention exchanges control-oriented information with immediately connected neighbors to establish potential cooperation consensus, and to generate cooperative control actions. To achieve this goal, a distributed model predictive control (DMPC) scheme is developed accounting for driving safety and efficiency. By coupling the states of collaborators in the optimization index, connected vehicles achieve fundamental highway maneuvers cooperatively and optimally. The performance of the distributed control scheme and the energy-saving potential of conducting such cooperation are tested in a mixed highway traffic environment by the means of microscopic simulations.     

Development of VT-Micro model for estimating hot stabilized light duty vehicle and truck emissions

The paper applies a framework for developing microscopic emission models (VT-Micro model version 2.0) for assessing the environmental impacts of transportation projects. The original VT-Micro model was developed using chassis dynamometer data on nine light duty vehicles. The VT-Micro model is expanded by including data from 60 light duty vehicles and trucks. Statistical clustering techniques are applied to group vehicles into homogenous categories. Specifically, classification and regression tree algorithms are utilized to classify the 60 vehicles into 5 LDV and 2 LDT categories. In addition, the framework accounts for temporal lags between vehicle operational variables and measured vehicle emissions. The VT-Micro model is validated by comparing against laboratory measurements with prediction errors within 17%.     

An ontological model to support communications of situation-aware vehicles

In an Intelligent Transport System (ITS) environment, the communication component is of great importance to support interactions between vehicles and roadside infrastructure. Previous studies have focused on the physical capability and capacity of the communication technologies, but the equally important development of suitable and efficient semantic content for transmission received notably less attention. Ontology is one promising approach for context modelling in ubiquitous computing environments, and in the transport domain it can be used both for context modelling and semantic contents for vehicular communications. This paper explores the development of an ontological model implementing relative geo-semantic information messages to support vehicle-to-vehicle communications. The proposed ontology model contains classes, objects, their properties/relations as well as some functions and query templates to represent and update the information of dynamic vehicles, inter-vehicle interactions and behaviour. This model was developed through a scenario enabling the evaluation of traffic conflict resolution approaches, by implementing a set of decision-making processes for intelligent vehicles. Given the scope of the proposed ontology modelling, it shows how vehicular communications can be used to update each vehicle’s context model. This work can be easily extended for more complex interactions among vehicles and the infrastructure.     

我国公路运输温室气体排放清单研究

本文结合国际形势和国内外研究成果,研究提出我国公路运输温室气体排放清单编制范围、评估对象、编制原则、清单建立方法、排放因子和活动水平确定方法,以及清单编制的技术路线。其中提出公路运输温室气体排放清单建立的三种方法,分别是基于燃料消耗的量化方法、基于车辆的量化方法和基于交通流的量化方法,并采用上述方法结合我国公路运输发展现状和相关研究成果,编制了包含私人交通在内的2008年我国全社会公路运输温室气体排放清单,并结合理论研究和案例分析,提出我国编制公路运输温室气体排放清单的问题与建议。     

Collecting ambient vehicle trajectories from an instrumented probe vehicle: High quality data for microscopic traffic flow studies

This paper presents the methodology and results from a study to extract empirical microscopic vehicular interactions from a probe vehicle instrumented with sensors to monitor the ambient vehicles as it traverses a 28 mi long freeway corridor. The contributions of this paper are two fold: first, the general method and approach to seek a cost-effective balance between automation and manual data reduction that transcends the specific application. Second, the resulting empirical data set is intended to help advance traffic flow theory in general and car following models in particular. Generally the collection of empirical microscopic vehicle interaction data is either too computationally intensive or labor intensive. Historically automatic data extraction does not provide the precision necessary to advance traffic flow theory, while the labor demands of manual data extraction have limited past efforts to small scales. Key to the present study is striking the right balance between automatic and manual processing. Recognizing that any empirical microscopic data for traffic flow theory has to be manually validated anyway, the present study uses a “pretty good” automated processing algorithm followed by detailed manual cleanup using an efficient user interface to rapidly process the data. The study spans roughly two hours of data collected on a freeway during the afternoon peak of a typical weekday that includes recurring congestion. The corresponding data are being made available to the research community to help advance traffic flow theory in general and car following models in particular.     

Definition of a merging assistant strategy using intelligent vehicles

In the area of active traffic management, new technologies provide opportunities to improve the use of current infrastructure. Vehicles equipped with in-car communication systems are capable of exchanging messages with the infrastructure and other vehicles. This new capability offers many opportunities for traffic management. This paper presents a novel merging assistant strategy that exploits the communication capabilities of intelligent vehicles. The proposed control requires the cooperation of equipped vehicles on the main carriageway in order to create merging gaps for on-ramp vehicles released by a traffic light. The aim is to reduce disruptions to the traffic flow created by the merging vehicles. This paper focuses on the analytical formulation of the control algorithm, and the traffic flow theories used to define the strategy. The dynamics of the gap formation derived from theoretical considerations are validated using a microscopic simulation. The validation indicates that the control strategy mostly developed from macroscopic theory well approximates microscopic traffic behaviour. The results present encouraging capabilities of the system. The size and frequency of the gaps created on the main carriageway, and the space and time required for their creation are compatible with a real deployment of the system. Finally, we summarise the results of a previous study showing that the proposed merging strategy reduces the occurrence of congestion and the number of late-merging vehicles. This innovative control strategy shows the potential of using intelligent vehicles for facilitating the merging manoeuvre through use of emerging communications technologies.     

Highway traffic state estimation with mixed connected and conventional vehicles: Microscopic simulation-based testing

This paper presents a thorough microscopic simulation investigation of a recently proposed methodology for highway traffic estimation with mixed traffic, i.e., traffic comprising both connected and conventional vehicles, which employs only speed measurements stemming from connected vehicles and a limited number (sufficient to guarantee observability) of flow measurements from spot sensors. The estimation scheme is tested using the commercial traffic simulator Aimsun under various penetration rates of connected vehicles, employing a traffic scenario that features congested as well as free-flow conditions. The case of mixed traffic comprising conventional and connected vehicles equipped with adaptive cruise control, which feature a systematically different car-following behavior than regular vehicles, is also considered. In both cases, it is demonstrated that the estimation results are satisfactory, even for low penetration rates.