A Comparison of Alternative Obstacle Avoidance Strategies for Vehicle Control

In Alleyne (1996) several vehicle control options were considered for Unintended Roadway Departure (URD) prevention and conclusions were drawn as to the efficacy of each method. This companion paper investigates the use of several different inputs for the control of a vehicle, in the context of Obstacle Avoidance for autonomous vehicles. In this investigation, the goal of the controller is to provide an intervention in the event of the vehicle detecting an obstacle in its path. The five types of inputs that will be considered are (i) Four Wheel Steering; (ii) Front Wheel Steering; (iii) Four Wheel Brake Steering; (iv) Front Wheel Brake Steering; and (v) Rear Wheel Brake Steering. The controller design is an LQ controller based on the simplified dynamics of a 2 degree of freedom bicycle model. However, the analysis of the different strategies are performed on a more complete, nonlinear vehicle model. A key contribution of this paper is the quantitative evaluation of the relative efficiencies of each of these input strategies being examined. Unlike most control schemes, an important metric of performance is the ratio of peak tire force used versus available tire force. The conclusions reached in this paper shed additional light on appropriate input actuator methods for vehicle guidance and control.     

A Comparison of Alternative Obstacle Avoidance Strategies for Vehicle Control

SUMMARY

In Alleyne (1996) several vehicle control options were considered for Unintended Roadway Departure (URD) prevention and conclusions were drawn as to the efficacy of each method. This companion paper investigates the use of several different inputs for the control of a vehicle, in the context of Obstacle Avoidance for autonomous vehicles. In this investigation, the goal of the controller is to provide an intervention in the event of the vehicle detecting an obstacle in its path. The five types of inputs that will be considered are (i) Four Wheel Steering; (ii) Front Wheel Steering; (iii) Four Wheel Brake Steering; (iv) Front Wheel Brake Steering; and (v) Rear Wheel Brake Steering. The controller design is an LQ controller based on the simplified dynamics of a 2 degree of freedom bicycle model. However, the analysis of the different strategies are performed on a more complete, nonlinear vehicle model. A key contribution of this paper is the quantitative evaluation of the relative efficiencies of each of these input strategies being examined. Unlike most control schemes, an important metric of performance is the ratio of peak tire force used versus available tire force. The conclusions reached in this paper shed additional light on appropriate input actuator methods for vehicle guidance and control.     

Direct tire force generation algorithm based on non-iterative nonlinear inverse tire model

The function of vehicle dynamics control system is adjusting the yaw moment, the longitudinal force and lateral force of a vehicle body through several chassis systems, such as brakes, steering and suspension. Individual systems such as ESC, AFS and 4WD can be used to achieve desired performance by controlling actuator variables. However, integrated chassis control systems that have multiple objectives may not simply achieve the desired performance by controlling the actuators directly. Usually those systems determine the required tire forces in an upper level controller and a lower level controller regulates the tire forces through the actuators. The tire force is controlled in a recursive way based on vehicle state measurement, which may not be sufficient for fast response. For immediate force tracking, we introduce a direct tire force generation method that uses a nonlinear inverse tire model, a pseudo-inverse model of vehicle dynamics and the relationship between longitudinal force and brake pressure.     

Drive control system design for stability and maneuverability of a 6WD/6WS vehicle

This paper describes a drive controller designed to improve the lateral vehicle stability and maneuverability of a 6-wheel drive / 6-wheel steering (6WD/6WS) vehicle. The drive controller consists of upper and lower level controllers. The upper level controller is based on sliding control theory and determines both front and middle steering angle, additional net yaw moment, and longitudinal net force according to the reference velocity and steering angle of a manual drive, remotely controlled, autonomous controller. The lower level controller takes the desired longitudinal net force, yaw moment, and tire force information as inputs and determines the additional front steering angle and distributed longitudinal tire force on each wheel. This controller is based on optimal distribution control and takes into consideration the friction circle related to the vertical tire force and friction coefficient acting on the road and tire. Distributed longitudinal/lateral tire forces are determined as proportion to the size of the friction circle according to changes in driving conditions. The response of the 6WD/6WS vehicle implemented with this drive controller has been evaluated via computer simulations conducted using the Matlab/Simulink dynamic model. Computer simulations of an open loop under turning conditions and a closed-loop driver model subjected to double lane change have been conducted to demonstrate the improved performance of the proposed drive controller over that of a conventional DYC.     

Selection of Actuator Combination in Integrated Chassis Control Using Taguchi Method

This paper presents a method to select the actuator combination in integrated chassis control using Taguchi method. Electronic stability control (ESC), active front and rear steering (AFS/ARS) are used as an actuator, which is needed to generate a control tire force. After computing the control yaw moment in the upper-level controller, it is distributed into the control tire forces, generated by ESC, AFS and ARS in the lower-level controller. In this paper, the weighted pseudo-inverse control allocation (WPCA) with variable weights is used to determine the control tire forces of each actuator. Taguchi method is adopted for sensitivity analysis on variable weights of WPCA in terms of the control performances such as the maneuverability and the lateral stability. For sensitivity analysis, simulation is performed on a vehicle simulation package, CarSim. From sensitivity analysis, the most effective actuator combination is selected.     

Handling Capabilities of Vehicles in Emergencies Using Coordinated AFS and ARMC Systems

In this paper, an advanced control technique that can be implemented in hard emergency situations of vehicles is introduced. This technique suggests integration between Active Front Steering (AFS) and Active Roll Moment Control (ARMC) systems in order to enhance the vehicle controllability. For this purpose, the AFS system applies a robust sliding mode controller (SMC) that is designed to influence the steering input of the driver by adding a correction steering angle for maintaining the vehicle yaw rate under control all the time. The AFS system is then called active-correction steering control. The ARMC system is designed to differentiate the front and rear axles' vertical suspension forces in order to alter the vehicle yaw rate and to eliminate the vehicle roll motion as well. Moreover, the operation of the SMC is based on tracking the behavior of a nonlinear 2-wheel model of 2-DOF used as a reference model. The 2-wheel model incorporates real tire characteristics, which can be inferred by the use of trained neural networks. The results clearly demonstrate the enhanced characteristics of the proposed control technique. The SMC with the assistance of the ARMC provides less correction of the steering angle and accordingly reduces the possibility of occurrence of the saturation phenomenon that is likely to take place in the operation of the SMC systems.     

Handling Capabilities of Vehicles in Emergencies Using Coordinated AFS and ARMC Systems

In this paper, an advanced control technique that can be implemented in hard emergency situations of vehicles is introduced. This technique suggests integration between Active Front Steering (AFS) and Active Roll Moment Control (ARMC) systems in order to enhance the vehicle controllability. For this purpose, the AFS system applies a robust sliding mode controller (SMC) that is designed to influence the steering input of the driver by adding a correction steering angle for maintaining the vehicle yaw rate under control all the time. The AFS system is then called active-correction steering control. The ARMC system is designed to differentiate the front and rear axles' vertical suspension forces in order to alter the vehicle yaw rate and to eliminate the vehicle roll motion as well. Moreover, the operation of the SMC is based on tracking the behavior of a nonlinear 2-wheel model of 2-DOF used as a reference model. The 2-wheel model incorporates real tire characteristics, which can be inferred by the use of trained neural networks. The results clearly demonstrate the enhanced characteristics of the proposed control technique. The SMC with the assistance of the ARMC provides less correction of the steering angle and accordingly reduces the possibility of occurrence of the saturation phenomenon that is likely to take place in the operation of the SMC systems.     

Modeling and Analysis of Automotive Antilock Brake Systems Subject to Vehicle Payload Shifting

The steerability and stability of vehicles must be maintained during emergency stopping and evasive driving maneuvers on degraded road surfaces. The introduction of antilock brake and traction control systems (ABS/TCS) has expanded the envelope of safe vehicle operation for the majority of drivers. These mechatronic systems combine an electronic controller with wheel speed sensors, an electro-mechanical hydraulic brake actuator, and in some instances, engine intervention through the engine control unit, to regulate wheel slip. The development of ABS systems has traditionally depended on extensive in-vehicle testing, at cold weather proving grounds, which contribute to lengthy product development cycles. However, recent attention has been focused on the use of simulation and hardware-in-the-loop strategies to emulate test conditions in a controlled setting to shorten product design time and methodically address critical safety issues. In this paper, the effect of transient load shifting due to cargo movement on ABS performance in light-duty vehicles will be investigated. Analytical and empirical mathematical models are presented to describe the chassis, tire/road interface, wheel, brake modulator, and cargo dynamics. Two strategies, a model-free table lookup and model-based discrete nonlinear controller, are presented to regulate the ABS modulator's operation. These vehicle and controller dynamics have been integrated into a simulation tool to investigate the effect of transient weight transfers on the vehicle's overall stopping distance and time. Representative numerical results are presented and discussed to quantify the ABS systems' performance for various loading and operating conditions.     

Multi-axle vehicle dynamics stability control algorithm with all independent drive wheel

The stability driving characteristic and the tire wear of 8-axle vehicle with 16-independent driving wheels are discussed in this paper. The lateral stability of 8-axle vehicle can be improved by the direct yaw moment which is generated by the 16 independent driving wheels. The hierarchical controller is designed to determine the required yaw torque and driving force of each wheel. The upper level controller uses feed-forward and feed-backward control theory to obtain the required yaw torque. The fuzzification weight ratio of two control objective is built in the upper level controller to regulate the vehicle yaw and lateral motions. The rule-based yaw moment distribution strategy and the driving force adjustment based on the safety of vehicle are proposed in the lower level controller. The influence of rear steering angle is considered in the distribution of driving force of the wheel. Simulation results of a vehicle double lane change show the stability of 8-axle vehicle under the proposed control algorithm. The wear rate of tire is calculated by the interaction force between the tire and ground. The wear of tire is different from each other for the vehicle with the stability controller or not.     

Fault-tolerant braking control with integerated EMBs and regenerative in-wheel motors

This paper presents a fault-tolerant brake torque controller for four-wheel-distributed braking systems with in-wheel motors and Electro-Mechanical Brakes (EMB). Mechanical and electrical faults can degrade the performance of the EMB actuators and, thus, their effects need to be compensated in vehicle dynamics level. In this study, the faults are identified as performance degradation and expressed by the gains of each actuator. Assuming the brake force distribution and the regenerative braking ratios, the over-actuated braking system is simplified into a two-input system. A sliding mode controller is designed to track the driver’s braking and steering commands, even if there exist faults in EMBs. In addition, adaptive schemes are constructed to achieve the fault-tolerant control in braking. The proposed controller and strategies are verified in the EMB HILS (Hardware-in-loop-simulation) unit for various conditions.     

Automated Emergency Four-Wheel-Steered Vehicle Using Continuous Gain Equations

Advanced Vehicle Control Systems (AVCS), when realized, should substantially increase the convenience and safety of highway travel. Automated lateral control is an important step in the realization of AVCS. Much research has been concerned with lateral control during low-g maneuvers. However, before passengers' lives are in the hands of any automated laterally-controlled vehicle, the vehicle controller must be designed to respond to emergency situations where high-g maneuvers may be necessary.

This paper presents the development of a nonlinear-gain-optimized (NGO) controller for emergency automated lateral control of four wheel steered automobiles. Continuous gain equations (GE) are used to account for changes in the vehicle speed. The NGO controller uses a linear vehicle/tire model to define the state model. The response of a nonlinear vehicle/tire model is used to choose the performance index that optimizes the feedback gains for high-g emergency maneuvers at discrete speeds. Continuous gain equations are then derived as least-square approximations to each set of gains.

The performance of the four-wheel-steer continuous gain equations (4WS-GE) controller is compared to that of a two-wheel-steer continuous gain equations (2WS-GE) controller. Significant improvements in vehicle response are realized by using the 4WS-GE controller. The robustness of the controller's performance is examined with respect to changes in tire parameters and changes in vehicle mass.     

Requirement-based testing of an automotive ECU considering the behavior of the vehicle

HILS (Hardware In the Loop Simulation) and RBT (Requirement-Based Testing) are widely used to evaluate the performance and reliability of automotive ECUs (Electronic Control Units). The HILS method is used to predict the behavior of ECU-installed vehicles and to evaluate the performance of ECU controllers. RBT evaluates whether the embedded system satisfies the pre-defined requirements. In this study, the behavior of a vehicle is regarded as a system requirement, and an embedded system test procedure that evaluates the system requirement is proposed. In particular, a new method is introduced, which integrates HILS with RBT. Using the proposed method, the behavior of an articulated vehicle equipped with an AWS (All Wheel Steering) ECU is evaluated with RBT software.     

Effects of Model Complexity on the Performance of Automated Vehicle Steering Controllers: Controller Development and Evaluation

SUMMARY

Due to increased traffic congestion and travel times, research in Advanced Vehicle Control Systems (AVCS) has focused on automated lateral and headway control. Automated vehicles are seen as a way to increase freeway capacity and vehicle speeds while reducing accidents due to human error. Recent research in automated lateral control has focused on vehicle control during low-g maneuvers. To increase safety, automated lateral controllers will need to recognize and react to emergency situations.

This paper investigates the effects of vehicle and tire model order on the response of automated vehicles to an emergency step lane change using a controller based on linear vehicle and tire models. From these studies it is concluded that control strategies based solely on linear vehicle and tire models are inadequate for emergency vehicle maneuvers.

A strategy is then proposed to automatically control vehicles through emergency maneuvers. Here the response of a nonlinear vehicle model is used with a linear state model to optimize controller gains for nonlinear maneuvers. An emergency step lane change is used as a preliminary test of the method.     

Performance of Low-bandwidth, Semi-active Damping Concepts for Suspension Control

Active damping has been shown to offer increased suspension performance in terms of vehicle isolation, suspension packaging, and road-tire contact force. It can even approximate the performance of full state feedback control without requiring the difficult measurement of tire deflection. Many semi-active damping strategies have been introduced to approximate the response of active damping with the modulation of passive damping parameters. These strategies have typically required a relatively high bandwidth for actuator response. This paper investigates the simulation performance and “frequency response” of two concepts in low-bandwidth semi-active suspension control, one that sets a damping force directly and another that sets the damping resistance. The electronically controlled bandwidth of these actuators is approximately an order of magnitude less than other semi-active devices; high frequency control is handled mechanically. A quarter-car model is studied with the controlled damping replacing both passive and active damping of typical control schemes. Both low-bandwidth damping strategies perform remarkably well compared to both active and high-bandwidth, semi-active damping. In certain dynamic performances, the new semi-active strategies outperform active damping and what the author calls “nominal” semi-active damping.     

线控制动系统防抱死特性模糊控制方法的仿真研究

作者研究分析了直接影响汽车行驶安全性能的汽车制动系统的重要组成部分,阐述了以油或空气作为传力介质的传统制动系统必将被全电的制动系统——线控制动系统所取代,线控制动系统是未来制动系统的发展方向。介绍了线控制动系统的分类、结构和工作原理;建立了线控制动系统和制动执行器的数学模型,以1/4车辆模型为研究对象,设计了模糊控制器,并在Matlab/Simulink下进行了仿真分析。仿真结果表明,模糊控制对线控制动系统的防抱死特性取得了理想的控制效果。     

Performance of Low-bandwidth,Semi-active Damping Concepts for Suspension Control

Abstract

Active damping has been shown to offer increased suspension performance in terms of vehicle isolation, suspension packaging, and road-tire contact force. It can even approximate the performance of full state feedback control without requiring the difficult measurement of tire deflection. Many semi-active damping strategies have been introduced to approximate the response of active damping with the modulation of passive damping parameters. These strategies have typically required a relatively high bandwidth for actuator response. This paper investigates the simulation performance and “frequency response” of two concepts in low-bandwidth semi-active suspension control, one that sets a damping force directly and another that sets the damping resistance. The electronically controlled bandwidth of these actuators is approximately an order of magnitude less than other semi-active devices; high frequency control is handled mechanically. A quarter-car model is studied with the controlled damping replacing both passive and active damping of typical control schemes. Both low-bandwidth damping strategies perform remarkably well compared to both active and high-bandwidth, semi-active damping. In certain dynamic performances, the new semi-active strategies outperform active damping and what the author calls “nominal” semi-active damping.     

Optimal Performance of Variable Component Suspensions

Most vehicle suspension systems use fixed passive components that offer a compromise in performance between sprung mass isolation, suspension travel, and tireroad contact force. Recently, systems with discretely adjustable dampers and air springs been added to production vehicles. Active and semi-active damping concepts for vehicle suspensions have also been studied theoretically and with physical prototypes. This paper examines the optimal performance comparisons of variable component suspensions, including active damping and full-state feedback, for “quartercar” heave models. Two and three dimensional optimizations are computed using performance indicators to find the component parameters (control gains) that provide “optimal” performance for statistically described roadway inputs. The effects of performance weighting and feedback configuration are examined. Active damping is shown to be mainly important for vehicle isolation. A passive vehicle suspension can control suspension travel and tire contact force nearly as well as a full state feedback control strategy.     

Robust control and actuator dynamics compensation for railway vehicles

A robust controller is designed for active steering of a high speed train bogie with solid axle wheel sets to reduce track irregularity effects on the vehicle’s dynamics and improve stability and curving performance. A half-car railway vehicle model with seven degrees of freedom equipped with practical accelerometers and angular velocity sensors is considered for the H_∞ control design. The controller is robust against the wheel/rail contact parameter variations. Field measurement data are used as the track irregularities in simulations. The control force is applied to the vehicle model via ball-screw electromechanical actuators. To compensate the actuator dynamics, the time delay is identified online and is used in a second-order polynomial extrapolation carried out to predict and modify the control command to the actuator. The performance of the proposed controller and actuator dynamics compensation technique are examined on a one-car railway vehicle model with realistic structural parameters and nonlinear wheel and rail profiles. The results showed that for the case of nonlinear wheel and rail profiles significant improvements in the active control performance can be achieved using the proposed compensation technique.     

基于视觉识别的线控制动压力滑模控制

制动安全是车辆主动安全的关键技术之一。制动决策和执行器控制是影响线控制动系统性能的两个主要因素。路面自适应性和控制器鲁棒性分别对制动决策和执行器控制有着重要影响,制约着线控制动系统的发展。本文中以一种液压调控的线控制动系统为基础,针对路面自适应性和控制器鲁棒性问题,提出一种双层结构的制动系统控制器,上层采用计算机视觉的方法对路面类型进行识别,根据识别结果制定当前路面的最佳滑移率;下层针对制动系统参数不确定性问题,引入滑模控制理论对制动过程中的最佳滑移率进行跟踪控制。通过仿真与实验验证,结果表明,双层结构的制动系统控制器相比传统控制器,路面的自适应性好,制动距离更短,控制器鲁棒性好。     

Effects of Model Complexity on the Performance of Automated Vehicle Steering Controllers: Model Development,Validation and Comparison

SUMMARY

Recent research on autonomous highway vehicles has begun to focus on lateral control strategies. The initial work has focused on vehicle control during low-g maneuvers at constant vehicle speed, typical of lane merging and normal highway driving. In this paper, and its companion paper, to follow, the lateral control of vehicles during high-g emergency maneuvers is addressed. Models of the vehicle dynamics are developed, showing the accuracy of the different models under low and high-g conditions. Specifically, body roll, tire and drive-train dynamics, tire force saturation, and tire side force lag are shown to be important effects to include in models for emergency maneuvers. Current controllers, designed for low-g maneuvers only, neglect these effects. The follow on paper demonstrates the performance of lateral controllers during high-g lateral emergency maneuvers using these vehicle models.