Using stop bar detector information to determine turning movement proportions in shared lanes

Turning vehicle volumes at signalized intersections are critical inputs for various transportation studies such as level of service, signal timing, and traffic safety analysis. There are various types of detectors installed at signalized intersections for control and operation. These detectors have the potential of producing volume estimates. However, it is quite a challenge to use such detectors for conducting turning movement counts in shared lanes. The purpose of this paper was to provide three methods to estimate turning movement proportions in shared lanes. These methods are characterized as flow characteristics (FC), volume and queue (VQ) length, and network equilibrium (NE). FC and VQ methods are based on the geometry of an intersection and behavior of drivers. The NE method does not depend on these factors and is purely based on detector counts from the study intersection and the downstream intersection. These methods were tested using regression and genetic programming (GP). It was found that the hourly average error ranged between 4 and 27% using linear regression and 1 to 15% using GP. A general conclusion was that the proposed methods have the potential of being applied to locations where appropriate detectors are installed for obtaining the required data. Copyright © 2016 John Wiley & Sons, Ltd.     

Innovative detector layout for automated traffic turning volume counting

Because of many advantages, loop detectors are the most common practice for obtaining data to control intersections. However, they have some drawbacks, including the fact that multiple detectors are usually required to monitor a location. The current practice in many cities is to install four consecutive loop detectors per lane, or two at the stop bar and one as an advanced detector. In some cities, there are also departure detectors. All these configurations have some practical problems and do not produce accurate counts especially in shared lanes. In this paper, a new placement configuration for departure detectors is proposed and named the mid‐intersection detector (MID). In this configuration, departure detectors are moved back to the middle of the intersection in such a way that they can be activated by more than one movement at different times. In some cases, departure detectors lack equations for calculating turning movements, a problem solved by MIDs because each movement passes more detectors along its path (without increasing the number of loops), and therefore they can produce more accurate and reliable data for obtaining turning movement counts. Copyright © 2017 John Wiley & Sons, Ltd.     

An Adaptive Neuro-Fuzzy Inference System for estimating the number of vehicles for queue management at signalized intersections

Queue management is a valuable but underutilized technique which could be used to minimize the negative impacts of queues during oversaturated traffic conditions. One of the main obstacles of applying queue management techniques along signalized arterials is the unavailability of a robust and sufficiently accurate method for measuring the number of vehicles approaching a signalized intersection. The method based on counting vehicles as they enter and exit a specific detection zone with check-in and check-out detectors is unreliable because of the likely systematic under or over counting and the resulting cumulative errors. This paper describes the application of the Adaptive Neuro-Fuzzy Inference System (ANFIS) in the development of a new fuzzy logic-based approach for estimating the Number of Vehicles in a Detection Zone (NVDZ) by using detector time-occupancy data (instead of detector counts). Microscopic simulation results are used to evaluate the accuracy of the NVDZ estimates. Tests were carried out to determine the transferability of a tuned Fuzzy Inference System (FIS) and to check the sensitivity of the calibrated FIS to detection coverage, the location of the detection zone relative to the signalized (bottleneck) intersection, the length of the detection zone, and different signal timings at the bottleneck intersection. Results show that the NVDZ estimation based on fuzzy logic seems to be a feasible approach. Although the primary objective of developing the NVDZ estimation technique has been queue management, other applications such as ramp metering and incident detection could potentially use the same technique.     

Data fusion algorithm for macroscopic fundamental diagram estimation

A promising framework that describes traffic conditions in urban networks is the macroscopic fundamental diagram (MFD), relating average flow and average density in a relatively homogeneous urban network. It has been shown that the MFD can be used, for example, for traffic access control. However, an implementation requires an accurate estimation of the MFD with the available data sources.Most scientific literature has considered the estimation of MFDs based on either loop detector data (LDD) or floating car data (FCD). In this paper, however, we propose a methodology for estimating the MFD based on both data sources simultaneously. To that end, we have defined a fusion algorithm that separates the urban network into two sub-networks, one with loop detectors and one without. The LDD and the FCD are then fused taking into account the accuracy and network coverage of each data type. Simulations of an abstract grid network and the network of the city of Zurich show that the fusion algorithm always reduces the estimation error significantly with respect to an estimation where only one data source is used. This holds true, even when we account for the fact that the probe penetration rate of FCD needs to be estimated with loop detectors, hence it might also include some errors depending on the number of loop detectors, especially when probe vehicles are not homogeneously distributed within the network.     

Average duration and performance of actuated signal phases

This paper describes an approach for evaluating alternative traffic detection designs for a signalized intersection. The models described in this paper can be used to determine the average phase duration and frequency of phase “max-out” as a function of the detector loop layout, detector unit timing, traffic demand, and approach speed. Layout and timing are described by the number of detectors on each approach served by the phase, detector location on each approach, detector length, and detector unit and controller time settings. The authors have used the concept of maximum allowable headway (MAH) to combine the many possible combinations of layout and timing variables into one representative quantity, which greatly simplifies the modelling process. The performance models were used to examine the sensitivity of intersection performance to a range of design values. In general, both phase duration and cycle length increase with higher demands or larger MAHs. Multiloop (i.e. two or more detection zones per lane) detector designs typically have larger MAHs than designs with one detector loop per lane. Phase duration and cycle length also increase for very low demand levels. In terms of performance, the maximum green duration was found to have a contrary effect at higher flow conditions. Larger maximum greens were found to reduce delays to the phase in service by reducing the probability of max-out but they increased delays to drivers waiting for service.     

Estimating arterial link speed using conventional road detectors

Abstract

In response to an initiative to develop an advanced traffic information system in Bangkok, this paper explores practical guidelines for the optimal location of road sensors, such that the data collected on spot speeds reflect an entire link's average speed. In particular, the authors use microsimulation software to investigate optimal detector locations, using the sum of squared errors and root mean squared errors. The analysis hypothesizes that road segments are 0.4, 0.6, 0.8, 1.0, 2.0 and 3.0 km in length and are specially designed to replicate typical arterial streets in Bangkok. The results show that a single detector location can produce good estimates of link speed only for segments that are shorter than 1.0 km. For distances of 1.0 km or more, the results suggest that two detectors be used for good link speed estimates under all traffic conditions.     

A gradient boosting logit model to investigate driver’s stop-or-run behavior at signalized intersections using high-resolution traffic data

Driver’s stop-or-run behavior at signalized intersection has become a major concern for the intersection safety. While many studies were undertaken to model and predict drivers’ stop-or-run (SoR) behaviors including Yellow-Light-Running (YLR) and Red-Light-Running (RLR) using traditional statistical regression models, a critical problem for these models is that the relative influences of predictor variables on driver’s SoR behavior could not be evaluated. To address this challenge, this research proposes a new approach which applies a recently developed data mining approach called gradient boosting logit model to handle different types of predictor variables, fit complex nonlinear relationships among variables, and automatically disentangle interaction effects between influential factors using high-resolution traffic and signal event data collected from loop detectors. Particularly, this research will first identify a series of related influential factors including signal timing information, surrounding traffic information, and surrounding drivers’ behaviors using thousands drivers’ decision events including YLR, RLR, and first-to-stop (FSTP) extracted from high-resolution loop detector data from three intersections. Then the research applies the proposed data mining approach to search for the optimal prediction model for each intersection. Furthermore, a comparison was conducted to compare the proposed new method with the traditional statistical regression model. The results show that the gradient boosting logit model has superior performance in terms of prediction accuracy. In contrast to other machine learning methods which usually apply ‘black-box’ procedures, the gradient boosting logit model can identify and rank the relative importance of influential factors on driver’s stop-or-run behavior prediction. This study brings great potential for future practical applications since loops have been widely implemented in many intersections and can collect data in real time. This research is expected to contribute to the improvement of intersection safety significantly.     

Real-time estimation of turning movement counts at signalized intersections using signal phase information

A variety of sensor technologies, such as loop detectors, traffic cameras, and radar have been developed for real-time traffic monitoring at intersections most of which are limited to providing link traffic information with few being capable of detecting turning movements. Accurate real-time information on turning movement counts at signalized intersections is a critical requirement for applications such as adaptive traffic signal control. Several attempts have been made in the past to develop algorithms for inferring turning movements at intersections from entry and exit counts; however, the estimation quality of these algorithms varies considerably. This paper introduces a method to improve accuracy and robustness of turning movement estimation at signalized intersections. The new algorithm makes use of signal phase status to minimize the underlying estimation ambiguity. A case study was conducted based on turning movement data obtained from a four-leg signalized intersection to evaluate the performance of the proposed method and compare it with two other existing well-known estimation methods. The results show that the algorithm is accurate, robust and fairly straightforward for real world implementation.     

Speed estimation and length based vehicle classification from freeway single-loop detectors

Roadway usage, particularly by large vehicles, is one of the fundamental factors determining the lifespan of highway infrastructure. Operating agencies typically employ expensive classification stations to monitor large vehicle usage. Meanwhile, single-loop detectors are the most common vehicle detector and many new, out-of-pavement detectors seek to replace loop detectors by emulating the operation of single-loop detectors. In either case, collecting reliable length data from these detectors has been considered impossible due to the noisy speed estimates provided by conventional data aggregation at single-loop detectors. This research refines non-conventional techniques for estimating speed at single-loop detectors, yielding estimates that approach the accuracy of a dual-loop detector’s measurements. Employing these speed estimation advances, this research brings length based vehicle classification to single-loop detectors (and by extension, many of the emerging out-of-pavement detectors). The classification methodology is evaluated against concurrent measurements from video and dual-loop detectors. To capture higher truck volumes than empirically observed, a process of generating synthetic detector actuations is developed. By extending vehicle classification to single-loop detectors, this work leverages the existing investment deployed in single-loop detector count stations and real-time traffic management stations. The work also offers a viable treatment in the event that one of the loops in a dual-loop detector classification station fails and thus, also promises to improve the reliability of existing classification stations.     

Length-based vehicle classification using event-based loop detector data

Length-based vehicle classification is an important topic in traffic engineering, because estimation of traffic speed from single loop detectors usually requires the knowledge of vehicle length. In this paper, we present an algorithm that can classify vehicles passing by a loop detector into two categories: long vehicles and regular cars. The proposed algorithm takes advantage of event-based loop detector data that contains every vehicle detector actuation and de-actuation “event”, therefore time gaps between consecutive vehicles and detector occupation time for each vehicle can be easily derived. The proposed algorithm is based on an intuitive observation that, for a vehicle platoon, longer vehicles in the platoon will have relatively longer detector occupation time. Therefore, we can identify longer vehicles by examining the changes of occupation time in a vehicle platoon. The method was tested using the event-based data collected from Trunk Highway 55 in Minnesota, which is a high speed arterial corridor controlled by semi-actuated coordinated traffic signals. The result shows that the proposed method can correctly classify most of the vehicles passing by a single loop detector.     

Vehicle reidentification and travel time measurement across freeway junctions using the existing detector infrastructure

Conventional vehicle detectors are capable of monitoring discrete points along the freeway but do not provide information about conditions on the link between detectors. Knowledge of conditions on the link is useful to operating agencies for enabling timely decisions in response to various delay causing events and hence to reduce the resulting congestion of the freeway system. This paper presents an approach that matches vehicle measurements between detector stations to provide information on the conditions over the link between the detectors rather than relying strictly on the aggregate point measurements from the detectors. In particular this work reidentifies measurements from distinct vehicles using the existing loop detector infrastructure. Here the distinct vehicles are the long vehicles, but depending on the vehicle population or type of detector used, one might chose to use some other reproducible feature.This new methodology represents an important advancement over preceding loop based vehicle reidentification, as illustrated herein, it enables vehicle reidentification across a major diverge and a major merge. The examples include a case where the reidentification algorithm responded to delay between two detector stations an hour before the delay was locally observable at either of the stations used for reidentification. While previous loop based reidentification work was limited to dual loop detectors, the present effort also extends the methodology to single loop detectors; thereby making it more widely applicable. Although the research uses loop detector data, the algorithm would be equally applicable to data obtained from many other traffic detectors that provide reproducible vehicle features.     

An intersection turning movement estimation procedure based on path flow estimator

Estimation of intersection turning movements is one of the key inputs required for a variety of transportation analysis, including intersection geometric design, signal timing design, traffic impact assessment, and transportation planning. Conventional approaches that use manual techniques for estimation of turning movements are insensitive to congestion. The drawbacks of the manual techniques can be amended by integrating a network traffic model with a computation procedure capable of estimating turning movements from a set of link traffic counts and intersection turning movement counts. This study proposes using the path flow estimator, originally used to estimate path flows (hence origin–destination flows), to derive not only complete link flows, but also turning movements for the whole road network given some counts at selected roads and intersections. Two case studies using actual traffic counts are used to demonstrate the proposed intersection turning movement estimation procedure. Copyright © 2010 John Wiley & Sons, Ltd.     

原油管道内部磁性杂质清理方法

为了清除附着在管道内壁上的铁磁性腐蚀产物,防止其在漏磁检测的过程中吸附到检测器上影响检测结果的精度,开发了直板钢刷清管器和磁力钢刷清管器。结果表明：清管器携带的钢刷能对管道内壁实现有效的打磨,对内壁上的腐蚀产物有较好的清理作用,磁力钢刷清管器具有打磨作用的同时还具有磁性,能有效地吸附铁磁性杂质,并能将其带出管外,清管效果更好。分析2种清管器的应用结果,制定了更优的清管工艺过程,其清管效果在检测工作中进行验证。     

A real-time adaptive signal control in a connected vehicle environment

The state of the practice traffic signal control strategies mainly rely on infrastructure based vehicle detector data as the input for the control logic. The infrastructure based detectors are generally point detectors which cannot directly provide measurement of vehicle location and speed. With the advances in wireless communication technology, vehicles are able to communicate with each other and with the infrastructure in the emerging connected vehicle system. Data collected from connected vehicles provides a much more complete picture of the traffic states near an intersection and can be utilized for signal control. This paper presents a real-time adaptive signal phase allocation algorithm using connected vehicle data. The proposed algorithm optimizes the phase sequence and duration by solving a two-level optimization problem. Two objective functions are considered: minimization of total vehicle delay and minimization of queue length. Due to the low penetration rate of the connected vehicles, an algorithm that estimates the states of unequipped vehicle based on connected vehicle data is developed to construct a complete arrival table for the phase allocation algorithm. A real-world intersection is modeled in VISSIM to validate the algorithms. Results with a variety of connected vehicle market penetration rates and demand levels are compared to well-tuned fully actuated control. In general, the proposed control algorithm outperforms actuated control by reducing total delay by as much as 16.33% in a high penetration rate case and similar delay in a low penetration rate case. Different objective functions result in different behaviors of signal timing. The minimization of total vehicle delay usually generates lower total vehicle delay, while minimization of queue length serves all phases in a more balanced way.     

Real-time queue length estimation for congested signalized intersections

How to estimate queue length in real-time at signalized intersection is a long-standing problem. The problem gets even more difficult when signal links are congested. The traditional input–output approach for queue length estimation can only handle queues that are shorter than the distance between vehicle detector and intersection stop line, because cumulative vehicle count for arrival traffic is not available once the detector is occupied by the queue. In this paper, instead of counting arrival traffic flow in the current signal cycle, we solve the problem of measuring intersection queue length by exploiting the queue discharge process in the immediate past cycle. Using high-resolution “event-based” traffic signal data, and applying Lighthill–Whitham–Richards (LWR) shockwave theory, we are able to identify traffic state changes that distinguish queue discharge flow from upstream arrival traffic. Therefore, our approach can estimate time-dependent queue length even when the signal links are congested with long queues. Variations of the queue length estimation model are also presented when “event-based” data is not available. Our models are evaluated by comparing the estimated maximum queue length with the ground truth data observed from the field. Evaluation results demonstrate that the proposed models can estimate long queues with satisfactory accuracy. Limitations of the proposed model are also discussed in the paper.     

A two-stage fuzzy logic controller for traffic signals

This paper presents the design and evaluation of a fuzzy logic traffic signal controller for an isolated intersection. The controller is designed to be responsive to real-time traffic demands. The fuzzy controller uses vehicle loop detectors, placed upstream of the intersection on each approach, to measure approach flows and estimate queues. These data are used to decide, at regular time intervals, whether to extend or terminate the current signal phase. These decisions are made using a two-stage fuzzy logic procedure. In the first stage, observed approach traffic flows are used to estimate relative traffic intensities in the competing approaches. These traffic intensities are then used in the second stage to determine whether the current signal phase should be extended or terminated. The performance of this controller is compared to that of a traffic-actuated controller for different traffic conditions on a simulated four-approach intersection.     

Improved vehicle classification from dual-loop detectors in congested traffic

Vehicle classification is an important traffic parameter for transportation planning and infrastructure management. Length-based vehicle classification from dual loop detectors is among the lowest cost technologies commonly used for collecting these data. Like many vehicle classification technologies, the dual loop approach works well in free flow traffic. Effective vehicle lengths are measured from the quotient of the detector dwell time and vehicle traversal time between the paired loops. This approach implicitly assumes that vehicle acceleration is negligible, but unfortunately at low speeds this assumption is invalid and length-based classification performance degrades in congestion.To addresses this problem, we seek a solution that relies strictly on the measured effective vehicle length and measured speed. We analytically evaluate the feasible range of true effective vehicle lengths that could underlie a given combination of measured effective vehicle length, measured speed, and unobserved acceleration at a dual loop detector. From this analysis we find that there are small uncertainty zones where the measured length class can differ from the true length class, depending on the unobserved acceleration. In other words, a given combination of measured speed and measured effective vehicle length falling in the uncertainty zones could arise from vehicles with different true length classes. Outside of the uncertainty zones, any error in the measured effective vehicle length due to acceleration will not lead to an error in the measured length class. Thus, by mapping these uncertainty zones, most vehicles can be accurately sorted to a single length class, while the few vehicles that fall within the uncertainty zones are assigned to two or more classes. We find that these uncertainty zones remain small down to about 10 mph and then grow exponentially as speeds drop further.Using empirical data from stop-and-go traffic at a well-tuned loop detector station the best conventional approach does surprisingly well; however, our new approach does even better, reducing the classification error rate due to acceleration by at least a factor of four relative to the best conventional method. Meanwhile, our approach still assigns over 98% of the vehicles to a single class.     

原油管道检测器通过能力评价方法

为了探明管道内部通过能力,保证管道内部腐蚀检测器的顺利投放,制定了由泡沫检测器到几何尺寸检测器的管道通过能力检测流程,并将此方法在多条原油管线上进行了验证。结果表明：该方法能准确地识别管线上的变形尺寸大小,并对变形部位进行定位。根据检测结果对管道通过能力进行评价,对不符合要求的管段及时进行修复,保证了后期检测的顺利进行。此外,在检测的过程中有效地清理了管道内部污物,提高检测器通过能力及管道的输油效率。     

Estimating vehicle miles traveled combined with ITS data

‘Vehicle miles traveled’ (VMT) is an important performance measure for highway systems. Currently, VMT [or ‘annual average daily traffic’ (AADT)] is estimated from a combination of permanent counting stations and short-term counts done at specified locations as part of the Highway Performance Monitoring System (HPMS) mandated by the US Federal Highway Administration. However, on some roadway sections, Intelligent Transportation Systems (ITS) such as detectors and cameras also produce traffic data. The question addressed in this paper is whether and under what conditions ITS systems data could be used instead of HPMS short-term counts (called ‘coverage counts’)? This paper develops a methodology for determining a threshold number of missing daily traffic counts, or alternatively, the number of valid ITS data observations needed, in order to confidently replace the HPMS coverage counts with ITS data.

Because ITS counts, coverage counts, and actual ground counts (e.g. continuous counts) cannot be found coexisting on a roadway section, it is hard to compare them directly. In this paper, the Monte Carlo simulation method is employed to generate synthetic ITS counts and coverage counts from a set of relatively complete traffic counts collected at a continuous count station. Comparisons are made between simulated ITS counts, coverage counts, and actual ground counts. The simulation results indicate that when there are<330 daily traffic counts missing in a set of ITS counts in a year, that is, when there are at least 35 days of valid data, ITS counts can be used to derive a better AADT than using coverage counts. This result is applied to calculate the VMT for the Hampton Roads region in Virginia. The comparison between the VMTs derived with using and not using the threshold number indicates that these two VMTs are significantly different.     

Optimal speed detector density for the network with travel time information

In the expressway network, detectors are installed on the links for detecting the travel time information while the predicted travel time can be provided by the route guidance system (RGS). The speed detector density can be determined to influence flow distributions in such a way that the precision of the travel time information and the social cost of the speed detectors are optimized, provided that each driver chooses the minimum perceived travel time path in response to the predicted travel time information. In this paper, a bilevel programming model is proposed for the network with travel time information provided by the RGS. The lower-level problem is a probit-based traffic assignment model, while the upper-level problem is to determine the speed detector density that minimizes the measured travel time error variance as well as the social cost of the speed detectors. The sensitivity analysis based algorithm is proposed for the bilevel programming problem. Numerical examples are provided to illustrate the applications of the proposed model and of the solution algorithm.