Influence of temperature on the tyre rolling resistance

Temperature is a very important factor controlling rolling resistance of road vehicle tyres. There are at least three different temperatures that may be considered as important factors controlling thermal conditions of the rolling tyre. The most common measure of the thermal conditions during tyre rolling is ambient air temperature. The other two are: pavement temperature and “tyre” temperature. Tyre temperature is the most difficult to establish, as temperatures of different parts of rolling tyres differ considerably, thus there is a problem to obtain representative values. In the authors’ opinion, air temperature is the most universal and reliable parameter to measure. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper test conditions in the future standardized on-road method of measuring rolling resistance. The results indicate that generally each tyre and pavement combination is influenced by the air temperature in a unique way, but at the same it is possible to propose some general influence factors that may be used to normalize measurements to the standard temperature of 25 °C.     

Experimental analysis of tyre-enveloping characteristics at low speed

In this study, experiments are conducted to investigate tyre-enveloping characteristics. Four different types of tyres are tested. Parameters such as different tyre inflation pressures, vertical loads and types of obstacles (cleats) are considered. In addition to vertical stiffnesses of all tyres, vertical and horizontal force variations while traversing different obstacles at low speed are studied. The effects of inflation pressure and vertical load on variations of force and moment are investigated. Static test results showed that after a certain vertical displacement, all curves in force–deflection diagrams plotted with and without cleat intersect regardless of cleat and tyre types, depending on the inflation pressure of the tyre, which can be called typical static tyre-enveloping characteristics. Test results at low speed show that there is a considerable influence of the vertical load on vertical and lateral force responses of a tyre.     

Identification of the mechanical properties of bicycle tyres for modelling of bicycle dynamics

Advanced simulation of the stability and handling properties of bicycles requires detailed road–tyre contact models. In order to develop these models, in this study, four bicycle tyres are tested by means of a rotating disc machine with the aim of measuring the components of tyre forces and torques that influence the safety and handling of bicycles. The effect of inflation pressure and tyre load is analysed. The measured properties of bicycle tyres are compared with those of motorcycle tyres.     

Identification of the characteristics of motorcycle and scooter tyres in the presence of large variations in inflation pressure

Stability and safety of road vehicles are largely affected by tyre properties. Single-track vehicles are characterised by weakly damped modes of vibration (weave and wobble) and therefore this phenomenon is even more important. This article focuses on the study of both steady-state and transient properties of motorcycle and scooter tyres in the presence of very low and very high inflation pressures. The steady-state properties are defined as lateral forces (side-slip and camber forces) and yaw torques (self-aligning and twisting). The transient properties are described in terms of relaxation length, which represents the distance needed to reach a certain percentage of the steady-state value of the tyre force. Experimental tests are carried out on a specific rotating disk machine. Three sets of tyres are analysed. Steady-state properties are measured by increasing step by step the values of camber and side-slip angles. Transient properties are studied carrying out tests with harmonic side-slip excitation and measuring the phase lag between the excitation (input) and the tyre force (output). Experimental results show important variations in tyre properties with inflation pressure with general trends of all the tested tyres and particular features related to the tyre's geometry. After the analysis and discussion of experimental results, the measured data are fitted by means of a specific version of the Magic Formula. The dependence of the Magic Formula's coefficients on inflation pressure is analysed and interpolation curves are given.     

Investigation of Features of Tyre Rolling at Non-Small Velocities on the Basis of a Simple Tyre Model with Distributed Mass Periphery

SUMMARY

On the basis of the brush-type tyre model the paper considers the interaction between steady-state rolling deformable wheel and flat road surface as well as corresponding force and moment characteristics of the wheel.

At least two zones of sliding, anisotropic dry friction, sliding friction coefficient speed-dependent and instantaneous leap of the friction coefficient when transition from sliding to adhesion zone occurs, have been taken into account, as well as distributed peripheral mass of tyre, elasticity, pseudo-dry friction and damping properties in radial, tangential and lateral directions of the elements at the wheel periphery, including a visco-elastic belt. Vertical force distribution in the contact area is not supposed to be known in advance and follows from the calculation. As a result, sliding zone lengths, distributed forces in contact area, six components of generalized road reaction reduced to the wheel center, and rolling resistance moment are found as functions of vertical load, movement velocity, longitudinal and side slip, friction in contact area with road, stiffnesses, dry friction and damping in the tyre model elements and of distributed peripheral mass.

A computer program developed in Fortran and results of calculations are of particular interest for qualitative analysis including steady rolling of studded tyre and also racing car and aircraft tyres which peripheral mass shows itself in a special way because of great movement velocities.     

Longitudinal wheel slip during ABS braking

Anti-lock braking system (ABS) braking tests with two subcompact passenger cars were performed on dry and wet asphalt, as well as on snow and ice surfaces. The operating conditions of the tyres in terms of wheel slip were evaluated using histograms of the wheel slip data. The results showed different average slip levels for different road surfaces. It was also found that changes in the tyre tread stiffness affected the slip operating range through a modification of the slip value at which the maximum longitudinal force is achieved. Variation of the tyre footprint length through modifications in the inflation pressure affected the slip operating range as well. Differences in the slip distribution between vehicles with different brake controllers were also observed. The changes in slip operating range in turn modified the relative local sliding speeds between the tyre and the road. The results highlight the importance of the ABS controller's ability to adapt to changing slip–force characteristics of tyres and provide estimates of the magnitude of the effects of different tyre and road operating conditions.     

Handling and safety enhancement of race cars using active aerodynamic systems

A methodology is presented in this work that employs the active inverted wings to enhance the road holding by increasing the downward force on the tyres. In the proposed active system, the angles of attack of the vehicle's wings are adjusted by using a real-time controller to increase the road holding and hence improve the vehicle handling. The handling of the race car and safety of the driver are two important concerns in the design of race cars. The handling of a vehicle depends on the dynamic capabilities of the vehicle and also the pneumatic tyres’ limitations. The vehicle side-slip angle, as a measure of the vehicle dynamic safety, should be narrowed into an acceptable range. This paper demonstrates that active inverted wings can provide noteworthy dynamic capabilities and enhance the safety features of race cars. Detailed analytical study and formulations of the race car nonlinear model with the airfoils are presented. Computer simulations are carried out to evaluate the performance of the proposed active aerodynamic system.     

Laboratory alignment procedure for improving reproducibility of tyre wet grip measurement

Since 2012, the Korean and EU governments have been running a tyre labelling system. All tyres sold in Korea have to carry a label that displays information of two performance criteria: rolling resistance and wet grip. The rolling resistance of the tyres determines their fuel efficiency grading, and the wet grip of the tyres determines their braking safety grading. The rolling resistance and wet grip measurements must be reproducible, so the same tests on the same tyres in different laboratories must produce the same results to ensure a fair comparison between tyres from different suppliers. In addition, a good reproducibility of testing results prevents market surveillance authorities from obtaining results different from those provided by suppliers when testing the same tyres. The laboratory alignment procedure for the rolling resistance measurements was developed and published as the EU Commission Regulation No. 1235 in 2011. However, the laboratory alignment procedure for the wet grip measurements has not yet been developed. Therefore, there are many differences in the wet grip test results among test laboratories throughout the world. The new procedure that is proposed for the wet grip measurement alignment for tyre testing laboratories can improve the reproducibility of the wet grip testing results, and five laboratory alignment tests were carried out between KATECH and five other test laboratories in the world to evaluate the results of the proposed procedure.     

Measurement of stress distributions in truck tyre contact patch in real rolling conditions

Stress distributions on three orthogonal directions have been measured across the contact patch of truck tyres using the complex measuring system that contains a transducer assembly with 30 sensing elements placed in the road surface. The measurements have been performed in straight line, in real rolling conditions. Software applications for calibration, data acquisition, and data processing were developed. The influence of changes in inflation pressure and rolling speed on the shapes and sizes of truck tyre contact patch has been shown. The shapes and magnitudes of normal, longitudinal, and lateral stress distributions, measured at low speed, have been presented and commented. The effect of wheel toe-in and camber on the stress distribution results was observed. The paper highlights the impact of the longitudinal tread ribs on the shear stress distributions. The ratios of stress distributions in the truck tyre contact patch have been computed and discussed.     

Effect of vertical and lateral coupling between tyre and road on vehicle rollover

The vehicle stability involves many aspects, such as the anti-rollover stability in extreme steering operations and the vehicle lateral stability in normal steering operations. The relationships between vehicle stabilities in extreme and normal circumstances obtain less attention according to the present research works. In this paper, the coupling interactions between vehicle anti-rollover and lateral stability, as well as the effect of road excitation, are taken into account on the vehicle rollover analysis. The results in this paper indicate that some parameters influence the different vehicle stabilities diversely or even contradictorily. And it has been found that there are contradictions between the vehicle rollover mitigation performance and the lateral stability. The direct cause for the contradiction is the lateral coupling between tyres and road. Tyres with high adhesion capacity imply that the vehicle possesses a high performance ability to keep driving direction, whereas the rollover risk of this vehicle increases due to the greater lateral force that tyres can provide. Furthermore, these contradictions are intensified indirectly by the vertical coupling between tyres and road. The excitation from road not only deteriorates the tyres’ adhesive condition, but also has a considerable effect on the rollover in some cases.     

基于现场测试的道路压电俘能系统电学性能

为全面测评道路压电俘能系统在开放交通条件下的电学性能,采用16个自主研制的15 cm × 15 cm × 3 cm压电俘能装置并联,设计俘能模块布设点位,铺筑道路压电俘能系统现场测试段,基于随机开放交通条件下道路压电俘能系统开路电压波形信号响应特征,系统研究了现场不同荷载、不同车速工况下道路压电俘能系统电学输出规律,并...     

Tyre pressure monitoring using a dynamical model-based estimator

In the last few years, various control systems have been investigated in the automotive field with the aim of increasing the level of safety and stability, avoid roll-over, and customise handling characteristics. One critical issue connected with their integration is the lack of state and parameter information. As an example, vehicle handling depends to a large extent on tyre inflation pressure. When inflation pressure drops, handling and comfort performance generally deteriorate. In addition, it results in an increase in fuel consumption and in a decrease in lifetime. Therefore, it is important to keep tyres within the normal inflation pressure range. This paper introduces a model-based approach to estimate online tyre inflation pressure. First, basic vertical dynamic modelling of the vehicle is discussed. Then, a parameter estimation framework for dynamic analysis is presented. Several important vehicle parameters including tyre inflation pressure can be estimated using the estimated states. This method aims to work during normal driving using information from standard sensors only. On the one hand, the driver is informed about the inflation pressure and he is warned for sudden changes. On the other hand, accurate estimation of the vehicle states is available as possible input to onboard control systems.     

Vehicle Energy Dissipation Due to Road Roughness

Road roughness and surface texture are known to affect tire rolling resistance; however, little emphasis has been placed on the consequent changes in total vehicle energy dissipation due to road roughness. Thus, tire rolling resistance, in isolation from vehicle contributed losses such as dissipation in the suspension, appears to be a weakness in present evaluation procedures as they relate to fuel economy and pollution level testing: Recent work by Funfsinn and Korst has shown that substantial and measurable increases in energy losses occur for vehicles traveling on rough roads. The present investigation uses vehicle axle accelerations as a means of examining various road surfaces. Correlation with computer simulations has allowed the development of a deterministic road roughness model which permits the prediction of energy dissipation in both the tire and suspension as functions of road roughness, tire pressure, and vehicle speed. Comparison to the experiments of Korst and Funfsinn results in good agreement and shows that total rolling loss increases of up to 20 percent compared to ideal smooth roads are possible. The aerodynamic drag coefficient is also found to increase while driving on rough roads.     

Vehicle Energy Dissipation Due to Road Roughness

SUMMARY

Road roughness and surface texture are known to affect tire rolling resistance; however, little emphasis has been placed on the consequent changes in total vehicle energy dissipation due to road roughness. Thus, tire rolling resistance, in isolation from vehicle contributed losses such as dissipation in the suspension, appears to be a weakness in present evaluation procedures as they relate to fuel economy and pollution level testing: Recent work by Funfsinn and Korst has shown that substantial and measurable increases in energy losses occur for vehicles traveling on rough roads. The present investigation uses vehicle axle accelerations as a means of examining various road surfaces. Correlation with computer simulations has allowed the development of a deterministic road roughness model which permits the prediction of energy dissipation in both the tire and suspension as functions of road roughness, tire pressure, and vehicle speed. Comparison to the experiments of Korst and Funfsinn results in good agreement and shows that total rolling loss increases of up to 20 percent compared to ideal smooth roads are possible. The aerodynamic drag coefficient is also found to increase while driving on rough roads.     

抗滑水轮胎技术的新发展

轮胎在湿路面上的行驶性能关系到汽车的安全性。阐述了国外开发的三种新型抗滑水轿车轮胎的设计思想，结构特点以及主要性能，介绍了提高轮胎在潮湿带水路面上行驶性能的新技术及其新发展，对开发国产高性能轿车轮肥具有现实的参考借鉴意义。     

Environmental effects on Pacejka’s scaling factors

A set of scaling factors has been introduced by Pacejka [Pacejka, H.B., 2002, Tyre and Vehicle Dynamics (Oxford: Butterworth Heinemann Editions)] into his Magic Formula tyre model to take into account the influence of a number of external overall parameters such as road roughness, weather conditions, suspension characteristics and so on. These scaling factors are important for a correct prediction of tyre–road contact forces, but are not a function of the tyre itself. Changing the point of view, one could say that scaling factors should remain constant for different tyres on the same circuit, with the same weather conditions and with the same car. After characterizing different tyres through indoor tests (that do not consider external overall parameters) and after having identified Pacejka’s coefficients with scaling factors equal to one, several outdoor experimental tests have been carried out to assess the influence of vehicle and road surface conditions on scaling factors. These experimental data allowed us to identify, through a minimization approach, the ‘best’ set of Pacejka’s scaling factors for that vehicle and for that tyre on that track. Scaling factors for equal track and vehicle but different tyres were compared to check whether their values remained constant. To access the validity of scaling factors, a comparison between experimental data, collected on an instrumented passenger car, and MB simulations considering unity and identified scaling factors’ values, were carried out. All experimental data shown in this article come from tests carried out within the VERTEC project, a European founded research project (Task 2.a and 2.b) that puts together knowledge coming from vehicle manufacturers (Volvo, Porsche and Centro Ricerche Fiat CRF), tyre manufacturers (Pirelli and Nokian Tyres), control logic manufacturers (Lucas Varity GmbH), road maintenance experts (Centres d’Études Techniques de l’Équipement CETE), transport research organizations (Transport Research Laboratory TRL, Swedish National Road and Transport Research Institute VTI) and universities (Helsinki University of Technology HUT, Politecnico di Milano and University of Florence UNIFI).     

集装箱运输车在不同坡道条件下燃油经济性的试验

通过理论分析、实车道路试验、加载或减载的模拟试验方法,研究了集装箱运输车在不同坡道上行驶时的燃油经济性,以作为客观评价在集装箱堆场最大允许纵坡道路条件下集装箱运输车经济性的指标。结果表明道路纵坡度的增加对汽车上坡时的油耗量影响很大,且载荷越大,影响越大。     

浅谈中央充放气系统充放时间计算

本文针对不同容积轮胎及充气压力下充放气系统所需充放时间进行计算,使其根据气温,路面状况的不同,自动调节控制轮胎气压,产生最大附着力而又不至于产生过大阻力,保证汽车始终保持最合理的运动状态,提高车辆的地面通过性和工作效率。     

智能型轮胎压路机的探索

基于轮胎压实的揉搓作用以及能使被压实材料具有良好的封闭性等特点,提出可以利用轮胎充气压力的变化来改变压实度,获取最佳压实效果。介绍了一种能根据被压实材料密实度的变化状况,自动调节轮胎充气压力的智能型轮胎压路机,并且分析了该设备的关键技术、控制原理和创新点。