基于LS—SVM逆系统方法的非线性动态矩阵控制

针对神经网络逆系统建模存在的诸多问题,提出了基于最小二乘法支持向量机的α阶逆系统方法的非线性动态矩阵控制新方法．将最小二乘支持向量机辨识非线性对象的α阶逆模型与原系统串联组成伪线性系统,根据线性动态矩阵预测控制方法对伪线性系统进行控制．仿真结果表明,系统存在扰动和模型参数发生变化时,依然具有很好的动、静态性能,且表现出很强的鲁棒性,证明了方法的有效性．该方法不依赖于系统的数学模型,简化了非线性对象动态矩阵控制器的设计,为非线性预测控制的研究提供了一种新途径．     

Nonlinear control for autonomous underwater glider motion based on inverse system method

Autonomous underwater gliders are highly efficient, buoyancy-driven, winged autonomous underwater vehicles. Their dynamics are multivariable nonlinear systems. In addition, the gliders are underactuated and difficult to maneuver, and also dependent on their operational environment. To confront these problems and to design an effective controller, the inverse system method was used to decouple the original system into two independent single variable linear subsystems. The stability of the zero dynamics was analyzed, and an additional closed-loop controller for each linear subsystem was designed by sliding mode control method to form a type of composite controller. Simulation results demonstrate that the derived nonlinear controller is able to cope with the aforementioned problems simultaneously and satisfactorily.     

Multiple models direct adaptive controller for a stochastic non-minimum phase system

For a stochastic non-minimum phase multivariable system, a multiple models direct adaptive controller is presented. It is composed of multiple fixed models with two adaptive models. The fixed models are used to cover the region where the system parameters jump and improve the transient response, while another two adaptive models are used to guarantee the stability. Utilizing generalized minimum variance design method, it adopts the stochastic system estimation algorithm with optimal controller design method to identify the controller parameter directly. Finally, the global convergence is given. The simulation proves the effectives of the controller proposed.     

一类非线性不确定时滞系统鲁棒控制器的设计

利用LMI方法,针对不确定时滞系统的鲁棒模糊控制器设计及稳定性,提出了基于T—S的模糊模型,得到了使系统渐近稳定且具有H∞-扰动抑制度的模糊状态反馈控制器存在的充分条件,此充分条件以线性矩阵不等式的形式给出,因而具有数值易解性．     

Hierarchy-Based Adaptive Generalized Predictive Control for Aerial Grasping of a Quadrotor Manipulator

In this paper, an adaptive generalized predictive control(GPC) based on hierarchical control strategy is designed for a quadrotor with a robotic arm. For this nonlinear and coupled system, a two-layer control structure is adopted to achieve more precise trajectory tracking and keep the tracking performance after aerial grasping.The inner-layer controller is a proportional-derivative(PD) controller. The outer-layer subsystem is linearized by input-output linearization first and an adaptive generalized predictive controller is applied. The effectiveness of this approach is verified through the simulation using MATLAB/Simulink. A PD controller with feedforward control input is applied on such a system for a comparative study. Simulation results show that a better tracking performance can be achieved by the proposed strategy.     

DESIGN OF A NEW INTERPOLATED CONTROLLER FOR STABILIZATION OF A SET OF INTERPOLATED PLANTS

IntroductionDynamics of almost all plants in reality variesaccording to the condition under which the plantis operated.An idea to describe the variation ofplant dynamics is interpolating a number of rep-resentative models defined at representative op-erating points.In Ref. [1 ] ,the plant was as-sumed to described as a linear interpolation ofproper stable coprime factorizations of transferfunctions of two representative models and thestabilization problems have been considered. InRef.[2 ] ,it…     

一类非线性系统的神经网络内模优化控制

研究一类可用Ｈａｍｍｅｒｓｔｅｉｎ模型描述的ＭＩＳＯ非线性系统的优化控制方法，提出一种基于前向神经网络的Ｈａｍｍｅｒｓｔｅｎ模型，以描述ＭＩＳＯ非线性对象并给出具有内模结构的优化控制器设计方法，从而实现了在稳态优化与动态优化双重指标下的设定值闭环优化控制。针对汽油管道调合系统进行的仿真实验，验证了该方法的有效性。     

Nonlinear feedforward and feedback control design for autonomous underwater glider

Underwater gliders are highly efficient, buoyancy-driven, and winged autonomous underwater vehicles. Their dynamics are multivariable nonlinear systems with unstable internal dynamics and thus their motion control is a significant challenge. To improve the inherent efficiency and enhance the behavior of the underwater glider over a wide operating regime, a nonlinear feedforward and feedback controller was developed. The nonlinear feedforward control design is based on a new stable inversion technique which determines a causal and bounded solution for the unstable internal dynamics. The feedback control law was designed by a quadratic optimal control method. Simulation results show that the derived control system is able to deal with nonminimum phase system and successfully achieves the tracking of planned output trajectories from initial to final conditions. Furthermore, the control effort is very low, which means the glider with limited power storage has longer range and higher endurance.     

A Constrained Controller Based on State Estimation

IntroductionIn practice, owing to the limitations of actua-tors and other physical properties, the inputs of asystem are often subject to constraints. It has sig-nificant theoretical and engineering values to inves-tigate the control of constrained systems. In thepast years, many attempts have been made on thisissue[1-5]. For a class of uncertain constrained dis-crete-time systems, Kothare, et al[4]proposed anonline receding predictive control algorithm. Byanalyzing the degradation condition …     

Looper-tension <Emphasis Type="Italic">H</Emphasis><Subscript>∞</Subscript> control for hot strip finishing mills

The development of an innovative H _∞ controller for looper and tension control in hot strip finishing mills is traced based on approximately linearized model. This solution has been considered thanks to its well-known robustness and simplicity characteristics concerning disturbances’ attenuation. The controller is designed based on an optimal problem with linear matrix inequality (LMI) constraints, and the problem is solved by the mincx function of Matlab LMI Toolbox. Simulation results show the effectiveness of the proposed controller compared with conventional ones.     

前馈多源信息下异构动力学卡车队列协同控制系统

针对目前卡车队列动力学异构性所导致的系统弦稳定性、内部稳定性以及队列耦合性降低的问题,提出了一种异构协同自适应巡航系统控制器设计方法,建立了基于前馈多源信息的异构动力学卡车队列闭环耦合系统;考虑由异构车型所构成的卡车队列存在发动机执行器的饱和态异构问题,建立了发动机饱和性和状态约束条件;在上层协同控制器的基础上,建立了一种非线性下层异构发动机扭矩输出控制模型,用于控制车辆动力学仿真软件TruckSim中的真实车辆模型;建立了基于三维燃油特性图的车辆能耗模型,用于计算实时车辆油耗和节能性分析;通过频域分析法,结合已知异构动力学参数量化标定了协同自适应巡航系统控制器的增益,确保系统满足弦稳定条件。分析结果表明：相比同构动力学控制器,异构协同自适应巡航系统控制器可以确保距离误差在-0.01～0.15 m内,优于同构控制器作用下的-0.3～0.5 m,且当领航车进入匀速行驶状态时,跟随车辆能立刻收敛至相同的行驶状态,收敛性能优于同构协同自适应巡航控制系统;卡车队列节油率最大可达8.15%,随着车头时距减小至0.5 s,平均节油率最大可达8.10%。由此可见,多源前馈信息异构控制系统能有效降低车...     

带有UKBF的船舶动力定位预测控制器设计

为了精准设计水面船舶动力定位控制系统,将无迹卡尔曼布西滤波与非切换解析模型预测控制方法相结合提出一种预测控制器的设计方法.采用无迹卡尔曼布西滤波算法解决非线性连续系统的滤波问题,获取船舶运动状态的估计值;结合相对阶概念,根据船舶运动非线性模型,应用非切换解析模型预测控制方法设计动力定位非线性控制器,使船舶保持在指定位置.研究结果表明:设计控制器的输出较为平滑,有利于减少推进器磨损;设计控制器使船舶北向位置调节时间小于40 s,超调量小于5%,东向位置调节时间小于60 s,超调量小于5%,艏向角度的最大偏移量小于1.5°,令船舶快速到达了指定位置.      

Application of Nonlinear Predictive Control Based on RBF Network Predictive Model in MCFC Plant

This paper described a nonlinear model predictive controller for regulating a molten carbonate fuel cell (MCFC). A detailed mechanism model of output voltage of a MCFC was presented at first. However, this model was too complicated to be used in a control system. Consequently, an off line radial basis function (RBF) network was introduced to build a nonlinear predictive model. And then, the optimal control sequences were obtained by applying golden mean method. The models and controller have been realized in the MATLAB environment. Simulation results indicate the proposed algorithm exhibits satisfying control effect even when the current densities vary largely.     

Nonlinear and Variable Structure Excitation Controller for Power System Stability

A new nonlinear variable structure excitation controller is proposed. Its design combines the differential geometry theory and the variable structure controlling theory. The mathematical model in the form of ＂an affme nonlinear system＂ is set up for the control of a large-scale power system. The static and dynamic performances of the nonlinear variable structure controller are simulated. The response of system with the controller proposed is compared to that of the nonlinear optimal controller when the system is subjected to a variety of disturbances. Simulation results show that the nonlinear variable structure excitation controller gives more satisfactorily static and dynamic performance and better robustness.     

基于航速调整的班轮燃油补给优化

燃油成本在班轮运营总成本中占有很大比重,燃油补给是影响航运公司班轮运营成本和效益的一项重要决策.基于航速调整策略,以班轮运营总成本最小化为目标,建立燃油补给混合整数非线性规划模型,运用分段线性逼近法对燃油消耗函数进行线性化处理,并设计了求解算法步骤.实例分析验证了模型和求解方法的有效性.结果表明,在航运市场需求低迷的情况下,船舶更适宜采取较低的航速,采取灵活的加油港策略或放宽船舶到港时间窗限制,能更为有效地降低燃油成本.     

Robust intelligent control design for marine diesel engine

This work deals with the nonlinear control of a marine diesel engine by use of a robust intelligent control strategy based on cerebellar model articulation controller （CMAC）. A mathematical model of diesel engine propulsion system is presented. In order to increase the accuracy of dynamical speed, the mathematical model of engagement process based on the law of energy conservation is proposed. Then, a robust cerebellar model articulation controller is proposed for uncertain nonlinear systems. The concept of active disturbance rejection control （ADRC） is adopted so that the proposed controller has more robustness against uncertainties. Finally, the proposed controller is applied to engine speed control system. Both the model of the diesel engine propulsion system and of the control law are validated by a virtual detailed simulation environment. The prediction capability of the model and the control efficiency are clearly shown.     

LARGE SIGNAL DISCRETE-TIME MODEL FOR PARALLELED BUCK CONVERTERS

Introduction　　 In recent years,due to the rapid advances ofcomputer and communication,the power suppliesmust provide high current up to hundreds of am-peres and still have high efficiency and reliability.Under such requirements,multimodule- parallelingstructure is usually used and the load current isequally shared. The practical implementation ofthese distributed converters system is not alwaysstraightforward and various control problems arisebecause of undesirable interaction among subsys-t…     

ģ������ӦPID����������ABS�еķ����о�

无论是经典还是现代控制理论,大多是建立在线性系统基础上,目前对非线性系统还没有比较成熟的理论.常规PID控制在对象变化时,控制器的参数不能自动修改适应.将模糊控制与PID控制相结合,利用模糊推理方法实现对PID参数的在线自整定,设计了一种模糊自适应PID控制器.在分析汽车模型的基础上,采用PID控制、模糊自适应PID控制两种方法,联合Simulink软件分别对汽车的防抱死制动系统（ABS）进行刹车运动仿真研究,极大地提高了模糊控制方法和PID控制算法的应用性能.结果表明,模糊自适应PID控制方法可以达到更好的制动效果,提高了系统的动态性能和安全性能.     

基于PSO算法的磁浮系统PID控制器优化与评价

为了改善磁浮系统的非线性和不稳定性特点,利用微分几何方法将两个不同结构的非线性子系统转化为两个相同结构的线性子系统,设计了基于标准粒子群算法的比例积分微分控制器.从固定惯性权重、线性递减惯性权重和线性微分递减惯性权重中,选出适合电磁铁1和电磁铁2的固定惯性权重,得到电磁铁1控制器的固定惯性权重参数C为0.5,电磁铁2控制器的固定惯性权重参数C为0.49,并且通过建立模糊综合评价模型得出优化后的电磁铁1和电磁铁2的控制器抗干扰的能力是好,且好的隶属度皆为0.561 9.实验结果表明,优化后的磁浮系统具有较好的鲁棒性.      

分布式网络控制系统的输出反馈控制

建立了同时具有前向通道传输时延和反馈通道传输时延的线性分布式网络控制系统的数学模型.用该数学模型将系统变换为具有状态与控制时变时滞的线性时滞系统.基于代数Riccati方程方法,提出了H∞鲁棒输出反馈控制方法,以使系统闭环控制稳定.仿真算例结果表明,在t=2.5 s时,系统状态都达到了0,保证了系统具有较快的零状态响应速度.给出了这类系统的H∞鲁棒输出反馈控制器的综合设计示例.