共查询到19条相似文献,搜索用时 215 毫秒
1.
油气悬架耦连形式对车辆稳定性的影响 总被引:1,自引:0,他引:1
《汽车工程》2017,(12)
为各轮独立、同轴交连和对角交连3种耦连形式的油气悬架推导出其垂向力/刚度、侧倾力矩/刚度、俯仰力矩/刚度和扭转力矩/刚度公式,并据此建立了这3种油气悬架的Matlab/Simulink模型,通过仿真得到了悬架垂向、侧倾、俯仰和扭转的刚度特性曲线。对油气悬架Simulink模型与整车Carsim模型进行联合仿真,分析油气悬架不同耦连形式对车辆稳定性的影响。结果表明:油气悬架耦连形式对车辆垂向振动影响较小;对角交连油气悬架的车身俯仰角最小,其它两种耦连油气悬架的车身俯仰角相同且较大;同轴交连油气悬架的车身侧倾角最小,对角交连油气悬架的车身侧倾角次之,各轮独立油气悬架的车身侧倾角最大。 相似文献
2.
3.
五连杆式非独立悬架是螺旋弹簧作为弹性元件的非独立悬架的基础性结构,其他的如四连杆式以及双纵臂结构都是五连杆式的变形结构,五连杆各导向臂的受力分析,五连杆式非独立悬架的应用案例分析介绍。 相似文献
4.
以某4x4全驱沙漠车为研究对象,提出了一种简化的整车数学模型,建立了整车侧倾角与板簧、横向稳定杆刚度的函数关系,得到悬架侧倾角刚度对整车侧倾性能的影响。并介绍了横向稳定杆角刚度计算方法,前后悬架侧倾角刚度匹配原则。 相似文献
5.
横向稳定杆计算与汽车侧倾 总被引:1,自引:0,他引:1
主要阐述了与汽车横向稳定性有关的几个问题:横向稳定杆的设计:悬架侧倾角刚度及前后悬架侧倾角刚度的匹配:汽车侧倾轴线的确定及汽车侧倾角计算。讨论了提高汽车悬架侧向稳定性。 相似文献
6.
7.
8.
9.
运用虚功原理导出了悬架受力、弹簧刚度与悬架刚度之间、阻尼器参数与系统阻尼之间的非线性函数关系。开发了简单实用的双横臂-螺旋弹簧独立悬架仿真分析与设计软件,应用于某微型电动汽车的悬架系统设计。利用ADAMS建立双横臂悬架模型,通过仿真验证了公式及其结论的正确性。 相似文献
10.
11.
12.
13.
为分析扭转梁C特性对稳态转向性能的影响,文章以模态综合法建立了某乘用车扭转梁后悬柔性模型,对建立的原型车进行侧向力C特性仿真,与对标车进行对比发现仿真与试验值存大较大差异,且侧向力前束特性存在较大的过度转向趋势.通过优化安装衬套的刚度使得原型车与试验结果吻合,最后对整车进行稳态回转仿真发现,负的前束侧向力特性不利于转向,优化后的模型提高了整车不足转向. 相似文献
14.
15.
16.
Jung-Shan Lin Chiou-Jye Huang 《Vehicle System Dynamics: International Journal of Vehicle Mechanics and Mobility》2004,42(6):373-393
A fresh nonlinear backstepping design scheme, which is developed for the control of half-car active suspension systems to improve the inherent tradeoff between ride quality and suspension travel, is proposed in this paper. Since ride quality is dependent on a combination of vertical and angular displacements of a vehicle body, the design of active suspensions must have the potential to minimize heave and pitch movements in order to guarantee the ride comfort of passengers. The other important factor to be emphasized in the design of active suspensions is the suspension travel which means the space variation between the car body and the tires. In order to avoid damaging vehicle components and generating more passenger discomfort, the active suspension controllers must be capable of preventing the suspension from hitting its travel limits. Our design strategy, with two intentionally additional nonlinear filters, shows the potential to achieve these conflicting control objectives. The novelty of our active suspension design is in the use of two particular nonlinear filters at both the front and rear wheels. The effective bandwidths of these two nonlinear filters depend on the magnitudes of the front and rear suspension travels, individually. When suspension travel is small, the proposed controllers soften the suspension for enhancing passenger comfort. However, our control design shifts its attention to rattlespace utilization by stiffening the suspension when suspension travel approaches its limits. As a result, the improvement of tradeoff between ride quality and suspension travel can be guaranteed and is then demonstrated through comparative simulations. 相似文献
17.
18.
通过对全球乘用车传动及底盘结构进行统计分析,给出了乘用车驱动方式与车长、手动变速器与车长、自动变速器与车长、前单横臂后扭力梁组合与车长、前单横臂后多连杆组合与车长、前双横臂后多连杆组合与车长、装空气弹簧车辆与车长关系的统计数据。论述了乘用车不同车身形式所采用的弹性元件与稳定杆类别,以及乘用车所采用的不同制动方式。 相似文献
19.
江铃轻型货车行驶平顺性的改善 总被引:3,自引:0,他引:3
本文针对江铃轻型货车行驶平顺性不佳问题。进行了系统的道路试验,电液伺服模拟激振试验,模态试验和理论分析;查明了该车平顺性不佳的主要原因是前后悬架刚度过大,特别是后悬架在空载时;在不改变钢板弹簧安装尺寸的条件下对前后板簧进行了改进设计。试制后装车试验表明,行驶平顺性显著提高,操纵稳定性有一定改善。改进型板簧、台架的疲劳寿命达到了标准要求,在行驶可靠性试验中未出现板簧损坏。改进型板簧比原车板簧质量减轻 相似文献