基于线性路径跟踪控制的换道避撞控制策略研究

为实现车辆自主避撞，改善道路交通安全状况，提出一种基于线性路径跟踪控制的换道避撞控制策略。为实时确定制动和换道时机，获取跟车状态下自车和前车车速、加速度、相对距离以及驾驶人制动反应时间计算制动安全距离和换道安全距离，并在此基础上分别引入制动危险系数B和换道危险系数S评估制动与换道风险，使得车辆发生追尾碰撞的危险程度和主动干预阈值更直观。根据车辆期望横向加速度和期望横向位移的变化特性，采用5次多项式法规划符合驾驶人换道避撞特性的避撞路径。为保证换道避撞过程中驾驶人的安全舒适，采用最大横向加速度约束换道避撞轨迹。为实现对换道避撞路径的线性跟踪控制，保证车辆的操纵稳定性和横摆稳定性，基于车辆稳态动力学模型建立前馈控制，结合线性反馈控制消除换道路径的位置和横摆角偏差，修正参考路径实现直车道场景追尾避撞控制。仿真和实车交叉验证试验表明：根据车辆期望横向加速度和期望横向位移建立的符合驾驶人换道避撞特性的五次多项式换道路径与驾驶人实际换道避撞路径基本吻合，结合碰撞时间和车间时距的制动避撞控制策略能够在保证车辆行驶安全舒适性的同时有效避免车辆追尾碰撞，减少交通事故的发生。     

智能汽车自动紧急转向避撞的跟踪控制方法对比研究

为了提高智能汽车的主动安全性,提出3种不同的自动紧急转向避撞跟踪控制方法。首先建立汽车避撞简化模型,对制动、转向及两者相结合的3种不同避撞方式进行对比分析。其次,为深入研究汽车避撞过程中的实际响应,建立包含转向、制动及悬架3个子系统耦合特性的底盘18自由度统一动力学模型,并进行相关试验验证。随后构建智能汽车自动紧急转向避撞控制框架,对五次多项式参考路径和七次多项式参考路径的横摆角速度和横摆角加速度进行对比分析。接着以线性2自由度转向动力学模型为参考对象,对最优控制四轮转向、最优控制前轮转向、前馈与反馈控制相结合的前轮转向3种不同的跟踪控制系统分别进行设计。最后,以汽车底盘18自由度统一动力学模型为研究对象,对上述3种避撞控制系统进行仿真试验对比分析。研究结果表明：与制动避撞相比而言,转向避撞所需的纵向距离有较大降低,随着车速的增加和路面附着系数的越低,效果越明显;七次多项式参考路径比五次多项式参考路径的避撞过渡过程更为平缓,当实际车速与控制器所用车速不一致时,前者避撞性能表现更优;最优四轮转向控制系统在高、低2种不同附着路面都具有较好的避撞效果,最优前轮转向控制系统次之,而前馈与反馈相结合的前轮转向控制系统在低附着路面上则表现出严重的失稳。     

制动与转向协调动作的车辆避撞控制研究（双语出版）

为了弥补现有汽车避撞控制策略以及碰撞风险评价指标单一的不足，提出转向和制动协调的主动避撞控制系统。首先规划了五次多项式换道路径，在对其理论分析的基础上得到转向临界避撞距离和与目标车道车辆的安全距离约束。其次，考虑道路附着系数和系统延迟的影响，基于制动过程给出制动临界避撞距离，并以纵向行驶安全系数ξ和碰撞时间倒数T^-1_TC划分安全行驶区域，利用驾驶人实车跟车数据标定稳态跟随/定速巡航区域的阈值。随后，通过转向/制动临界避撞距离的对比给出2种避撞方式的安全收益范围。最后搭建Simulink/CarSim联合仿真模型，并对其进行不同初始条件下的避撞仿真试验。研究结果表明：转向操作在制动距离不足时仍是有效的；当主车高速近距离接近静止前车时，主车可以顺利采取转向换道动作，而常规ACC系统在2.5 s处的车间相对距离为-0.76 m，事实上已经发生了碰撞；当相邻车道前车与主车纵向间距不满足换道安全距离约束时，避撞控制系统进入紧急制动模式，最大制动减速度达到-0.8g（g为重力加速度），实际最小车间距为5.1 m；通过转向和制动的协调动作，充分发挥了车辆的避撞潜力；ξ和T^-1_TC指标的融合，可以更好地评估碰撞风险并实现不同控制模式的转换，在保证行车安全的同时可避免过分制动给乘客造成的紧张感。     

智能车辆主动避撞与稳定性联合控制仿真

为改善车辆在主动避撞过程中的车辆动力学特性,在MATLAB/Simulink环境下结合驾驶员模型分别设计了基于模糊控制理论的主动避撞控制处理器、制动稳定性控制器和转向稳定性控制器,从而能够在车辆主动避撞过程中综合考虑避撞和稳定性两个目标.并在ADAMS中建立了整车模型,联合MATLAB进行了仿真研究,仿真结果证明,在相...     

Emergency steering control of autonomous vehicle for collision avoidance and stabilisation

ABSTRACT

Collision avoidance and stabilisation are two of the most crucial concerns when an autonomous vehicle finds itself in emergency situations, which usually occur in a short time horizon and require large actuator inputs, together with highly nonlinear tyre cornering response. In order to avoid collision while stabilising autonomous vehicle under dynamic driving situations at handling limits, this paper proposes a novel emergency steering control strategy based on hierarchical control architecture consisting of decision-making layer and motion control layer. In decision-making layer, a dynamic threat assessment model continuously evaluates the risk associated with collision and destabilisation, and a path planner based on kinematics and dynamics of vehicle system determines a collision-free path when it suddenly encounters emergency scenarios. In motion control layer, a lateral motion controller considering nonlinearity of tyre cornering response and unknown external disturbance is designed using tyre lateral force estimation-based backstepping sliding-mode control to track a collision-free path, and to ensure the robustness and stability of the closed-loop system. Both simulation and experiment results show that the proposed control scheme can effectively perform an emergency collision avoidance manoeuvre while maintaining the stability of autonomous vehicle in different running conditions.     

Risk management algorithm for rear-side collision avoidance using a combined steering torque overlay and differential braking

This paper describes a risk management algorithm for rear-side collision avoidance. The proposed risk management algorithm consists of a supervisor and a coordinator. The supervisor is designed to monitor collision risks between the subject vehicle and approaching vehicle in the adjacent lane. An appropriate criterion of intervention, which satisfies high acceptance to drivers through the consideration of a realistic traffic, has been determined based on the analysis of the kinematics of the vehicles in longitudinal and lateral directions. In order to assist the driver actively and increase driver's safety, a coordinator is designed to combine lateral control using a steering torque overlay by motor-driven power steering and differential braking by vehicle stability control. In order to prevent the collision while limiting actuator's control inputs and vehicle dynamics to safe values for the assurance of the driver's comfort, the Lyapunov theory and linear matrix inequalities based optimisation methods have been used. The proposed risk management algorithm has been evaluated via simulation using CarSim and MATLAB/Simulink.     

融合预瞄与势场栅格法的紧急避撞驾驶人模型

紧急避障工况下的驾驶人操作具有响应快且动作幅值较大的特点，传统预瞄驾驶人模型已不能适应紧急避障工况的需求，故考虑实际避撞场景开发相应的驾驶人模型就显得尤为必要。针对此种状况，基于驾驶模拟器，结合紧急避撞工况实际驾驶人操纵数据，提出了一种融合预瞄与势场栅格法的紧急避撞驾驶人模型。首先针对紧急避撞工况下车辆运动特点，建立车辆横、纵向耦合非线性动力学模型，并给出其状态空间方程描述；其次，离线仿真分析紧急避撞系统特征，并结合线性二次型最优控制，建立最优曲率预瞄+跟踪误差反馈驾驶人模型；再者，基于紧急避撞工况下真实驾驶人经验转向行为数据，开发基于势场栅格法的驾驶人模型，为进一步提高驾驶人模型对避障行驶工况的适应性，将基于势场栅格法的驾驶人模型与最优曲率预瞄+跟踪误差反馈驾驶人模型进行融合，并基于Sigmoid函数实现两者输出的权重分配；最后，针对所提出的融合预瞄与势场栅格法的驾驶人模型，开展基于避撞台架的驾驶人在环仿真试验以及实车试验。研究结果表明：在紧急避撞工况下，对比最优曲率预瞄+跟踪误差反馈驾驶人模型，融合预瞄与势场栅格法的驾驶人模型输出的转向动作与实际驾驶人行为较为接近，可在保证避障安全性的前提下，兼顾避障路径跟踪精度与车辆行驶的稳定性。     

Optimal control of brakes and steering for autonomous collision avoidance using modified Hamiltonian algorithm

ABSTRACT

This paper considers the problem of collision avoidance for road vehicles, operating at the limits of friction. A two-level modelling and control methodology is proposed, with the upper level using a friction-limited particle model for motion planning, and the lower level using a nonlinear 3DOF model for optimal control allocation. Motion planning adopts a two-phase approach: the first phase is to avoid the obstacle, the second is to recover lane keeping with minimal additional lateral deviation. This methodology differs from the more standard approach of path-planning/path-following, as there is no explicit path reference used; the control reference is a target acceleration vector which simultaneously induces changes in direction and speed. The lower level control distributes vehicle targets to the brake and steer actuators via a new and efficient method, the Modified Hamiltonian Algorithm (MHA). MHA balances CG acceleration targets with yaw moment tracking to preserve lateral stability. A nonlinear 7DOF two-track vehicle model confirms the overall validity of this novel methodology for collision avoidance.     

无人驾驶电动游览车底盘集成控制研究

介绍了具有自动寻迹行驶和遥控行驶2种模式的无人驾驶电动游览车,该车采用光电传感器自动辨识行驶路径,自动完成寻迹行驶,且在自主行驶过程中通过超声波传感器探测技术自动检测障碍物信息,具有防碰撞功能,在底盘控制上实现了无人驾驶技术、轮毂电机驱动技术和线控转向技术以及防碰撞技术等的集成控制,对于实现车辆的智能驾驶具有重要意义。     

基于横向安全距离模型的主动避障算法

现有的安全距离模型是基于纵向相对车速或减速度值建立的,没有考虑移动目标的横向运动特性。本文利用移动目标横穿马路的速度、相对位置,建立横向安全距离模型,并提出一种基于横向安全距离模型的主动避障算法。首先,根据横向移动目标横穿马路的速度、相对位置和自车的制动距离建立横向安全距离模型,设计主动避障算法。接着,为计及路面条件对制动效果的影响,引入当前行驶路面估算的附着系数峰值估算最大制动减速度,约束目标避障减速度,并调整制动强度,以适应不同路况的安全避障行驶。最后,以典型横向移动目标骑行者作为研究对象,通过PreScan/Simulink/CarSim联合仿真验证避障算法的有效性。结果表明:基于横向安全距离模型的主动避障算法能有效避免与骑行者碰撞,提高行车的主动安全性。     

智能汽车对无信号交叉口行人的避撞控制

针对智能汽车在无信号交叉口对横穿行人的避撞问题,研究了主动转向避撞控制策略。基于多层模型预测控制方法,采用分层控制策略设计局部规划层控制器与全局跟踪层控制器,在此基础上根据交叉口处汽车与行人的轨迹特征计算人车碰撞剩余时间,改进传统人工势场法构造避撞函数,规划出既能规避交叉口内存在碰撞风险的行人又能使偏差最小的局部避撞路径,并使智能汽车在满足多项动力学约束时准确跟踪参考路径,通过搭建CarSim/Simulink联合仿真平台,结合广东省2006—2018年交通事故数据库选取对交叉口人车碰撞有显著影响的因素,设计仿真场景进行仿真分析。结果表明:智能汽车能在多个初始点完成对参考路径的跟踪,控制器对不同速度和附着条件有较高的鲁棒性,高速低附着场景中,智能汽车横向加速度小于0.4 g、质心侧偏角小于2°、前轮侧偏角小于2.5°,各约束量满足舒适性和平稳性条件;4个典型交叉口场景中,智能汽车以不同速度直行或转弯通过交叉口,均能识别横穿行人中存在碰撞风险的行人实现主动转向避撞。      

Optimisation of active suspension control inputs for improved performance of active safety systems

A collocation-type control variable optimisation method is used to investigate the extent to which the fully active suspension (FAS) can be applied to improve the vehicle electronic stability control (ESC) performance and reduce the braking distance. First, the optimisation approach is applied to the scenario of vehicle stabilisation during the sine-with-dwell manoeuvre. The results are used to provide insights into different FAS control mechanisms for vehicle performance improvements related to responsiveness and yaw rate error reduction indices. The FAS control performance is compared to performances of the standard ESC system, optimal active brake system and combined FAS and ESC configuration. Second, the optimisation approach is employed to the task of FAS-based braking distance reduction for straight-line vehicle motion. Here, the scenarios of uniform and longitudinally or laterally non-uniform tyre–road friction coefficient are considered. The influences of limited anti-lock braking system (ABS) actuator bandwidth and limit-cycle ABS behaviour are also analysed. The optimisation results indicate that the FAS can provide competitive stabilisation performance and improved agility when compared to the ESC system, and that it can reduce the braking distance by up to 5% for distinctively non-uniform friction conditions.     

基于驾驶员跟车习惯的报警/避撞算法研究

在驾驶员实车实验的基础上,研究跟车工况中的驾驶员行为特性和习惯,建立驾驶员跟随车距模型,并结合对车辆制动过程的分析,研究分别基于驾驶员制动行为特性和驾驶员跟随车距模型的报警/避撞算法,通过改变算法的参数值,可使算法得到的报警/避撞时机符合不同驾驶员的驾驶习惯。利用实验数据对算法进行离线检验,验证该算法在报警/避撞系统中的适用性。     

Minimizing the Path Radius of Curvature for Collision Avoidance

When a driver is suddenly presented with an obstacle in his path, or realizes that his speed is too great for the curved road ahead, commonly he saturates both inputs of steering and braking and thereby jeopardizes his chances of successfully avoiding a collision or negotiating the turn. Although anti-lock braking systems (ABS) avoid saturation of the braking and steerability usually remains, there is evidence to suggest that the vehicle performance with this system could be greatly improved. Could the steering, in addition to the braking, be automatically controlled to improve the performance? Because these threatening situations are so variable, it is very difficult to find a controller which can override both driver inputs and is always beneficial. Using a very simple model of the vehicle, the concept of minimizing the average radius of curvature of the path through controlling both driver inputs is shown to always be beneficial, and worthwhile. The results also carry over to a more realistic model.     

基于交通信息的电动汽车制动策略及仿真

为了提高滑行能量回收经济性和踏板制动安全性、舒适性,基于交通信息,提出了电动汽车(EV)制动协调策略。分析了滑行制动的经济性,由交通信息和汽车行驶状态确定滑行制动强度;由道路信息和前方车辆信息建立汽车安全距离模型和碰撞预警策略,利用预警信息对滑行制动和踏板制动强度进行协调。对本策略进行仿真验证。结果表明:利用交通信息的滑行策略,在通行良好工况下综合能耗减少1.1%,拥堵工况下减轻驾驶员的制动疲劳;预警和协调策略避免了频繁预警,减小了紧急避撞触发几率。因此,利用交通信息能够辅助驾驶员进行更加合理的制动。     

视线遮挡条件下面向弱势道路使用者的避撞策略研究

由于视线障碍物造成的“鬼探头”事故已经成为当前城市道路交通事故的主要类型之一。针对汽车碰撞视线遮挡条件下横穿的弱势道路使用者(VRU)的场景, 设计了1种基于碰撞时间比和安全制动距离的避撞策略, 建立车辆与VRU的交通状态数学模型, 分析“鬼探头”场景下的制动避撞临界距离。结合临界距离和车辆与VRU的碰撞时间比, 将可以避免碰撞的场景分为3种工况, 分别采用不同的制动减速度, 建立自动紧急制动避撞策略。通过Euro NCAP CPNC测试场景对该策略与传统TTC制动算法进行比较分析。结果表明, 在Euro NCAP CPNC测试场景中, 自车利用该避撞策略在理想情况下能够在更高的车速情况下完成避撞; 在不能避免碰撞的高速行驶工况中较传统TTC算法能够更加有效降低碰撞速度, 同时降低事故重伤风险和死亡风险, 提高车辆的安全性。      

车辆防追尾碰撞安全系统

高速公路的事故类型中追尾碰撞占了很大的比例,因而开发车辆防追尾碰撞安全系统是非常必要的。文章分析了影响行车安全的各种因素,建立了安全车距数学模型,利用现代技术,构造了一种车辆防追尾碰撞安全系统。指出此安全系统能减少由于驾驶员分心和疲劳等原因导致的交通事故,最大限度地提高车辆行驶的安全性。     

汽车底盘控制技术的现状和发展趋势

电子控制系统在汽车底盘技术中的广泛应用极大地改善了汽车的主动安全性。常见的底盘控制系统可分为制动控制、牵引控制、转向控制和悬挂控制。介绍通过高速网络将各控制系统联成一体形成的全方位底盘控制(GCC),汽车开放性系统构架工程(AUTOSAR)和底盘的线控技术(X-by-w ire)。     

装载机避障轨迹规划及模型预测轨迹跟踪

轮式装载机在工作区域行驶时，避障过程频繁，以往的避障轨迹规划未考虑整车转向半径约束和车速变化，也较少考虑整车在动力学模型条件下的轨迹跟踪性能。针对上述情况，以自动驾驶轮式装载机为对象，基于最优快速随机扩展树算法（RRT^*），考虑车身膨胀圆个数，生成全局最优避障路径，以整车最小稳定转向半径为约束，利用CC-Steer算法对避障路径进行平滑处理，采用路径-速度分解算法规划满足整车在加速、匀速和减速状态下的避障行驶轨迹。基于整车动力学模型，考虑行驶过程中的横向位置偏差和航向角偏差，并将整车动力传动系统视为1阶惯性环节，构建装载机动力学状态空间方程。以加速度和铰接角为控制输入，以车速、横向位置偏差和航向角偏差为控制输出，建立整车动力学预测模型，以加速度、铰接角和车速为约束条件，将目标函数转换为二次规划问题，建立满足装载机在工作区域避障的模型预测轨迹跟踪控制系统。以规划的非匀速行驶避障轨迹为目标，利用构建的模型预测轨迹跟踪系统，进行自动驾驶轮式装载机的轨迹跟踪仿真。研究结果表明：所提方法能够很好地控制自动驾驶轮式装载机从初始位姿驶向目标位姿，实现整车在工作区域的避障过程，且在避障过程中满足整车的约束要求，保证整车在轨迹跟踪过程中的安全稳定性能。     

Modeling and control of an anti-lock brake and steering system for cooperative control on split-mu surfaces

The brake and steering systems in vehicles are the most effective actuators that directly affect the vehicle dynamics. In general, the brake system affects the longitudinal dynamics and the steering system affects the lateral dynamics; however, their effects are coupled when the vehicle is braking on a non-homogenous surface, such as a split-mu road. The yaw moment compensation of the steering control on a split-mu road is one of the basic functions of integrated or coordinated chassis control systems and has been demonstrated by several chassis suppliers. However, the disturbance yaw moment is generally compensated for using the yaw rate feedback or using wheel brake pressure measurement. Access to the wheel brake pressure through physical sensors is not cost effective; therefore, we modeled the hydraulic brake system to avoid using physical sensors and to estimate the brake pressure. The steering angle controller was designed to mitigate the non-symmetric braking force effect and to stabilize the yaw rate dynamics of the vehicle. An H-infinity design synthesis was used to take the system model and the estimation errors into account, and the designed controller was evaluated using vehicle tests.