HEV实时等效能量消耗最小控制策略

以变速器前置式并联结构为例,介绍了一种实时等效能量消耗最小控制策略。在研究车辆行驶于循环工况中消耗燃油热能和电能之间关系的基础上,针对该策略的关键问题———蓄电池组的电能和发动机的燃油热能消耗量的等效方法进行了详细阐述。最后在车辆仿真模型的基础上对该种策略进行仿真试验,并与其他类型的控制策略进行了比较。     

考虑发动机起停优化的PHEV能量管理策略

针对某新型双电机行星耦合插电式混合动力汽车(PHEV)中发动机在起停及怠速运行状态下会导致油耗增加的问题,基于等效燃油消耗最小能量管理策略,加入发动机起停优化控制模块,以进一步改善整车燃油经济性。建立了整车动力学和传动模型并加入发动机起停优化控制模块,对ECMS能量管理策略输出的发动机及电机最优目标转矩进行重新优化分配后,再输出给发动机及电机控制器以控制其工作状态。针对起停优化控制中影响起停频次的关键时间参数,采用粒子群优化算法对其进行优化。仿真结果表明,相比优化前,所提出的能量管理优化策略能够实现对发动机起停或怠速状态的有效控制,减少发动机的起停频次,减少恶化油耗,验证了本文所提出的能量管理优化策略能够进一步优化整车燃油经济性。     

并联混合动力汽车整车控制仿真

新能源汽车3大关键技术包括动力电池及其电池管理系统、驱动电机及其电机控制以及整车能量管理控制策略,整车控制策略直接决定能量流在汽车内部的流动及整车性能的好坏。文章利用模糊控制策略建立了详细的动力总成多能源能量管理控制模块,并通过ADVISOR仿真平台对所设计的控制策略进行仿真分析。仿真结果显示100km油耗仅5．1L,0-100km／h加速时间为23．1s,最大行驶速度168.3km／h;表明该能量管理策略能明显改善燃油经济性。动力性也具有较好表现。     

基于增益功率燃油系数的HEV能量管理策略

为了优化等效燃油最小能量管理策略的节油效果，以适用于工程批量应用为导向，制定基于增益功率燃油系数的混合动力汽车(HEV)能量管理策略。基于瞬时优化原理，提出基于增益功率燃油系数的工作模式决策机制，根据电机发电或电动引起的发动机功率与燃油消耗率的变化关系，分别给出电机充电和放电模式下增益功率燃油系数的计算方法。考虑发动机扭矩瞬态快速变化对油耗的影响和电机及电池包充放电效率特性，提出发动机高效区域扭矩滞回控制方法，建立基于增益功率燃油系数的能量管理策略算法架构。基于MATLAB/Simulink搭建控制策略软件模型，通过转鼓试验台进行实车试验验证。研究结果表明：相对于等效燃油最小能量管理策略，基于增益功率燃油系数的能量管理策略提升了节油率和舒适性，在全球轻型汽车测试循环(WLTC)工况下的百公里油耗降低了约4.8%，发动机的启停次数降低了约53%；相对于有效燃油消耗率(BSFC)最优工作点控制方法，发动机高效区域滞回控制方法降低百公里油耗约1.8%；与采用基于动态规划的全局优化能量管理策略的仿真结果对比，在不能提前预知工况的条件下，制定的能量管理策略在WLTC工况与新标欧洲测试循环(NEDC)工况下的油耗与理论最优值差距均较小。     

系统综合效率优化的插电式混合动力车辆的能量管理策略

为了提升插电式混合动力汽车(PHEV)的动力系统的真实能效,从综合能效最优的角度,研究了插电式混合动力系统能量管理策略。针对系统综合效率的时变性和耦合性,建立了系统效率评价模型,对电池储存电能的效率进行评价和动态修正,以系统综合效率最优为目标,结合粒子群优化算法,构建了能量管理策略。基于GT-Suite和Simulink联合仿真平台,分析了对能量管理策略的应用效果。结果表明:在连续2个“全球统一轻型汽车测试循环(WLTC)”下,与未考虑综合能效的能量管理策略相比,综合能耗降低了10.6%;优化后发动机和电机工况分布均更加合理,且在不同的工况下均能有效降低系统能耗。因此,该能量管理策略能提高插电式混合动力系统能效。     

新能源插电式混合动力汽车馈电时控制逻辑的分析与驾驶体验优化——不同混动架构与驾驶体验以及与能耗之间的关系分析

时代的发展使得环境污染问题愈发严重,机动车成为排放污染物的重要贡献者。因此,发展新能源汽车具有很强的战略性必要性。常见的混合动力汽车可粗略分为两大类:HEV 普通型混合动力汽车;PHEV 插电式混合动力汽车。前者的代表性车型为:丰田普锐斯、一汽丰田卡罗拉双擎。后者的代表车型为:比亚迪秦、荣威Ei6等国产车型。特殊车型为传祺GA5插电增程式电动车。本文重点介绍PHEV插电式混合动力汽车根据不同混动架构,在馈电时对驾驶质感以及能耗的影响做出分析、以及探讨可采取对应结构的改进方法及手段的可行性分析。PHEV插电式混合动力汽车馈电驾驶质感以及能耗的改变最终通过P0位置加装BSG电机或者P1位置加装ISG电机(适用于P3结构混合动力车型、代表车型比亚迪秦)、采用能量分流的混动架构(例如一汽丰田卡罗拉双擎)以及双电机增程式架构(例如传祺GS4 GA5新能源前轴发动机带动发电机发电输出动力的任务完全交给大功率的独立电机)等。通过该方式使得在馈电状态时,发动机与传动系脱藕,于最佳经济转速只用于发电。从而使能量得到最合理的利用、实现馈电油耗低、以及馈电行驶质感提升的目的。     

基于烟花算法的PHEV能量管理策略参数优化

为改善插电式混合动力汽车(PHEV)的燃油经济性,提出一种基于规则的能量管理策略。结合智能网联汽车技术,利用烟花算法(FWA)结合系统约束条件,对能量管理策略参数进行优化,以求使车辆在变化的路况下能耗最低。为减轻沉重运算负荷,设计了一种事件触发机制来控制优化操作的启停。当车辆油耗超过预设上限则开始优化,一旦油耗满足预设下限则优化结束。在中国典型城市工况下,验证了该策略的有效性及优化性能。结果显示:较优化前的能量管理策略,该方案可使PHEV燃料消耗降低10%。从而,使燃油经济性明显提升。     

Design of an energy management strategy for parallel hybrid electric vehicles using a logic threshold and instantaneous optimization method

A novel parallel hybrid electric vehicle (PHEV) configuration consisting of an extra one-way clutch and an automatic mechanical transmission (AMT) is taken as the study subject of this paper. An energy management strategy (EMS) combining a logic threshold approach and an instantaneous optimization algorithm is developed for the investigated PHEV. The objective of this EMS is to achieve acceptable vehicle performance and drivability requirements while simultaneously maximizing engine fuel economy and maintaining the battery state of charge (SOC) in its rational operation range at all times. Under the MATLAB/Simulink environment, a computer simulation model of the studied PHEV is established using the bench test results. Simulation results for the behavior of the engine, motor, and battery illustrate the potential of the proposed control strategy in terms of fuel economy and in keeping the deviations of SOC at a low level.     

混合动力客车循环工况下燃料经济性分析

在分析某混合动力客车的多种工作模式和循环工况的统计特性的基础上,给出最大能耗节约率计算方法.通过建立等效燃料消耗率的概念,详细分析各典型工况对该车燃料经济性的贡献率.最后提出混合动力城市客车控制策略制定的若干建议.     

并联混合动力汽车扭矩管理的模糊控制与仿真

并联混合动力汽车中内燃机和电机之间存在动力的耦合和分离过程,能量管理策略比较复杂。为了进一步合理分配内燃机和电机的动力输出,增强其能量管理策略的鲁棒性,文中分析了电辅助控制策略的不足,提出了基于模糊逻辑控制的包含驾驶员扭矩识别和蓄电池功率平衡的并联混合动力汽车扭矩分配策略,并利用ADVI SOR2002的仿真环境,完成了该模糊逻辑扭矩控制模块的仿真。结果表明,模糊逻辑控制策略满足控制目标,对提高汽车的动力性和燃油经济性、改善排放、保证蓄电池的充放电功率平衡有明显的作用。     

New Optimal Power Management Strategy for Series Plug-In Hybrid Electric Vehicles

Recently Plug-in hybrid electric vehicles (PHEVs) have gained increasing attention due to their ability to reduce the fuel consumption and emissions. In this paper a new efficient power management strategy is proposed for a series PHEV. According to the battery state of charge (SOC) and vehicle power requirement, a new rule-based optimal power controller with four different operating modes is designed to improve the fuel economy of the vehicle. Furthermore, the teaching-learning based optimization (TLBO) method is employed to find the optimal engine power and battery power under the specified driving cycle while the fuel consumption is considered as the fitness function. In order to demonstrate the effectiveness of the proposed method, four different driving cycles with various numbers of driving distances for each driving cycle are selected for the simulation study. The performance of the proposed optimal power management strategy is compared with the rule-based power management method. The results verify that the proposed power management method could significantly improve the fuel economy of the series PHEV for different driving conditions.     

基于电机最优回馈转矩曲线的制动控制策略

本文中首先基于电机等效电路模型,分析了车用内置式永磁同步电机的耗能制动状态和回馈制动状态;然后根据电机矢量控制原理,对控制电流指令进行解析,并经试验数据的验证;接着计算得到永磁同步电机最优回馈转矩曲线,并据此提出一种制动回馈能量最优的串联制动控制策略。最后针对某P4并联混合动力商用车,仿真分析了在C?WTVC、CHTC?TT循环工况和试验采集到的某段省道工况下,并联制动和所提出的串联最优制动控制策略下的百公里油耗和制动回收能量。结果表明,与并联制动控制相比,基于电机最优回馈转矩曲线的串联制动控制策略可降低油耗,并回收更多的制动能量,实现制动回收能量和燃油经济性的提升。     

基于遗传算法系统效率优化的PHEV电量保持模式控制策略

为了提高插电式混合动力汽车（PHEV）在电量保持下的燃油经济性,并解决插电式混合动力汽车在运行过程中动力元件效率对系统能量利用率影响的问题,制定了系统效率最优的控制策略。以PHEV关键动力部件的测试数据为基础,建立发动机、驱动电机、无级变速器（CVT）以及动力电池等关键部件的效率数值模型,并考虑了温度及荷电状态（SOC）对动力电池充放电功率的影响。设计以混合动力系统效率最优为适应度评价函数,将CVT速比、发动机转矩作为优化变量,以车速、加速度和SOC为状态变量,在动力性指标的约束下,运用遗传算法进行迭代寻优,PHEV的系统效率在第20代左右收敛于全局最优值。同时发动机转矩和CVT速比通过多代遗传进化,较快收敛于最佳值。将相关优化结果与车速、加速度拟合成相应的三维控制数表,综合数值建模和试验测试数据建模的方法,基于MATLAB/Simulink搭建插电式混合动力汽车整车控制策略仿真模型,采用新欧洲行驶循环工况进行仿真验证。结果表明：插电式混合动力汽车在电量保持模式下,利用遗传算法优化的系统效率最优控制策略相比优化前,动力电池SOC运行更为平稳,CVT效率有所提升,驱动电机及发动机转矩分配更为合理;百公里燃油消耗量从优化前的5.2 L降至4.5 L,燃油经济性提升了13.5%。     

燃料电池城市大客车驱动系统的发展现状及趋势

结合城市大客车运行工况，分析了城市大客车的运行特点及功率需求特点，并以此为基础讨论了燃料电池驱动系统以及燃料电池和各种可能的储能装置组成的混合驱动系统的优缺点。指出了燃料电池城市大客车的发展将呈现以纯氢或甲醇重整制氢为主要燃料、采用混合驱动方案、多个电动机驱动，提高工作电压等级等特点。     

Simulation of city bus performance based on actual urban driving cycle in China

This paper establishes the simulation model of a city bus on the basis of the EQ6110 bus prototype and its experimental data. According to the actual urban driving cycle, the fuel economy and the traction performance of the EQ6110 city bus have been simulated, and factors such as the driving cycle, the loss of power to engine accessories, the gear-shifting strategy, the fuel shut-off strategy of the engine, etc., which influence on the bus’s fuel economy, are also quantitatively analyzed. Some conclusions are drawn as follows: (1) driving cycles have a great influence on the fuel economy of a city bus; (2) under the typical urban driving cycle of the public bus in China, the engine fuel shut-off strategy can save about 1 to 1.5 percent of the fuel consumption; and (3) the optimized gear-shifting rules can save 6.7 percent of the fuel consumption. Experimental results verify that the fuel economy for the EQ6110 public bus is improved by 7.2 pecent over the actual Wuhan urban driving cycle of the current public bus in China.     

Hydraulic control system design for a PHEV considering motor thermal management

In this paper, a design method for a PHEV hydraulic control system was proposed considering motor thermal management. Dynamic models of the target PHEV were developed including the hydraulic system, which consists of one mechanical and one electric oil pump. The required motor cooling flow was designed based on the motor temperature, which was obtained from a one-dimensional thermal equivalent circuit model including the heat source and oil spray cooling. Combining the PHEV powertrain model, hydraulic control system model, and the motor thermal model including the cooling system, an integrated simulator was developed for the target PHEV. Using the integrated simulator, the temperatures of MG1 and MG2 were investigated for various motor cooling flow rates when the PHEV underwent a highway driving cycle. The energy consumption of the hydraulic control system was also evaluated. It was found from the simulation results that a hydraulic control system of the target PHEV could be designed that satisfied the required flow for the motor cooling, lubrication and brake control using the design procedure proposed in this study.     

A comparative study on the power characteristics and control strategies for plug-in hybrid electric vehicles

A comparative study was performed on two types of plug-in hybrid electric vehicles (PHEVs): the GM Volt and the Toyota Prius Plug-in Hybrid. First, the powertrain models of the two vehicles were derived. Based on the dynamic models, a detailed component control algorithm was developed for each PHEV. Specifically, a control algorithm was proposed for motor generator 1 (MG1) and MG2 to achieve optimal engine operation. Additionally, an energy management strategy for selecting the operation mode was developed from the viewpoint of fuel economy, battery state of charge and vehicle velocity. Using the dynamic model of the control algorithm for each PHEV, simulations were performed, and the simulation results were verified by comparing them with those obtained using the Powertrain System Analysis Toolkit simulator for the plug-in Prius. Based on the simulation results, a comparative study was performed, and it was found that the role and capacity of MG1 and MG2 and the mode selection algorithm must be determined depending on the configuration of the PHEV.     

黄海客车：4款产品彰显实力

2014北京客车展上,黄海客车重点展示了DD6821G01、DD6125CHEV1、DD6109PHEV1N和DD6930C01FX 4款创新产品,全面展示了其在新能源、燃气客车、校车以及城市支线公交领域的精耕细作。     

基于马尔可夫决策理论的燃料电池混合动力汽车能量管理策略

根据道路试验记录的数据建立驾驶员需求功率的马尔可夫模型,利用马尔可夫决策理论获得混合动力汽车的随机能量管理策略。借助燃料电池混合动力汽车控制系统的仿真平台进行仿真计算。北京公交车中速工况的仿真结果表明,与原先的恒电压控制策略相比,随机能量管理策略可以降低燃料消耗。     

Development of equivalent fuel consumption minimization strategy for hybrid electric vehicles

Power distribution between an internal combustion engine and electric motors is one of main features of hybrid electric vehicles that improves their fuel economy. An equivalent fuel consumption minimization strategy can instantaneously identify the optimal power distribution by converting the battery power into the equivalent fuel power and minimizing the overall fuel consumption. To guarantee the effectiveness of the strategy, it is essential to find the proper value of the conversion factor used to obtain the equivalent fuel power. However, finding the proper value is not a straightforward process because it is necessary to consider the overall power conversion efficiencies and battery charge sustaining strategy for the target driving cycle in advance. In this study, a model-based parameter optimization method is introduced to find the optimal conversion factor. A hybrid electric vehicle simulation model capable of estimating fuel consumption was developed, and the optimal conversion factor was discovered using a genetic algorithm that evaluates its population members using the simulation model. A series of simulations and vehicle tests was conducted to verify the effectiveness of the optimized strategy, and the results show a distinct improvement in fuel economy.