耐压船体结构典型接点疲劳寿命评估

潜艇在潜浮过程中,由于静水外压引起的工作应力与焊接残余应力叠加,形成拉压循环应力,导致耐压船体的局部结构可能出现低周疲劳裂纹.一般情况下,高强度钢在抗拉强度提高的同时往往伴随着材料塑性储备和断裂韧性的下降,因此分析高强度钢潜艇结构的低周疲劳寿命非常重要.本文基于断裂力学和Paris公式建立了潜艇耐压结构低周疲劳寿命的工程估算方法,根据裂纹无损检测的概率统计和含裂纹圆柱壳极限应力分析,给出了初始裂纹和裂纹临界状态的建议值.应用本文的简化方法分析了某潜艇结构和锥柱结合壳模型的低周疲劳寿命,锥柱结合壳模型的数值算例表明本文的计算结果与试验测试结果相吻合.     

在随机载荷作用下用断裂力学法估算潜艇耐压壳体的疲劳寿命和裂纹尺寸

潜艇在上浮下潜的过程中承受着反复作用的由外部水压力所产生的随机载荷,耐压壳体面临着疲劳破坏。本文引入了潜艇的疲劳载荷谱,模拟了潜艇随机载荷历程,并对一次载荷历程估算了疲劳寿命;同时模拟了100次载荷历程,分别对疲劳寿命和裂纹尺寸进行了统计,结果表明裂纹的疲劳寿命符合威布尔分布,裂纹扩展尺寸服从对数正态分布。该结论与目前疲劳可靠性分析中使用的对数正态分布模型和威布尔分布模型相一致。     

复杂载荷作用下潜艇结构疲劳裂纹扩展预报方法

统一疲劳裂纹扩展模型是课题组在McEvily模型基础上提出来的,它将疲劳裂纹扩展的3个扩展区域统一起来,并能解释更多的疲劳试验现象.本文介绍了统一疲劳裂纹扩展模型的基本表达式.将此模型与焊缝焊趾表面裂纹应力强度因子的计算方法结合起来,探讨复杂载荷作用下潜艇结构疲劳裂纹扩展预报方法.将服从Weibull分布的随机载荷系列编排为升序、降序载荷谱及随机载荷谱,预报潜艇锥柱结合壳焊缝焊趾处表面裂纹在3种载荷谱下的疲劳裂纹扩展情况,并分析随机载荷谱下载荷次序效应及初始裂纹尺寸对疲劳裂纹扩展行为的影响.结果表明,载荷次序效应对潜艇结构疲劳寿命的影响很明显,且合理的确定初始裂纹尺寸对潜艇结构的疲劳寿命预报是非常重要的.     

潜艇结构锥柱结合壳损伤容限研究

损伤容限与耐久性的结合体现了现代潜艇结构延长寿命、提高可靠性和降低维修成本的综合要求.损伤容限分析的关键问题是正确估算剩余寿命.本文以断裂力学为理论基础,通过对带有初始裂纹的潜艇典型焊接节点模型的剩余寿命有限元分析,将计算结果和试验结果相比较,考核剩余寿命有限元分析方法的可靠性,从而对有初始缺陷或裂纹的疲劳热点区域--潜艇锥柱结合壳进行剩余寿命有限元估算,在此基础上进行潜艇锥柱结合壳损伤容限研究.并对具有不同尺寸的初始裂纹结构的剩余寿命进行有限元分析,确定潜艇在交付使用和检修时的损伤容限尺寸.     

舰艇结构延寿处理的可行性研究

为适应现代海军舰艇的要求，提高舰艇结构的疲劳寿命，以保证舰艇在长期服役期间的安全性具有重要意义。本文综述了焊接残余应力对舰艇焊接结构疲劳寿命的影响，分析了各种主要延寿处理技术对舰艇结构的适应性。通过爆炸处理对潜艇用钢921性能影响的初步研究，着重分析了爆炸处理技术在舰艇结构延寿处理方面的可行性。     

带初始裂纹的潜艇典型焊接节点试件疲劳寿命分析

对带初始裂纹的潜艇典型焊接节点试件进行疲劳寿命有限元分析研究,并加工制造了典型焊接节点试件,对其进行疲劳试验,试验结果与数值分析结果基本吻合,说明对潜艇典型焊接结构的有限元应力分析、疲劳寿命分析的方法是正确可行的.     

高强钢焊接接头超声冲击效果对比试验研究

文章采用高强度钢对接焊试板,分别开展超声冲击前后残余应力变化和低周疲劳寿命的对比试验研究。试验结果表明:经过超声冲击处理后,焊缝区的残余应力从焊后的拉伸残余应力转化为压缩残余应力,焊接试样的低周疲劳寿命有显著提高,平均提高30%以上,试验验证了超声冲击技术在改善残余应力和提高疲劳寿命上的实用性和有效性。     

具初始裂纹钢桥梁焊接构件疲劳裂纹扩展和疲劳寿命计算

钢桥梁构件因焊接缺陷或者在疲劳应力交互作用下萌生裂纹,钢桥梁构件因存在初始裂纹大大地降低焊接构件的疲劳性能.文中考虑到焊接构件往往会存在初始缺陷,研究了含初始缺陷的桥梁焊接构件的疲劳分析方法.在已有的大量含裂纹构件的疲劳实验工作基础上,结合课题组所做的焊接构件疲劳实验资料,假设初始裂纹焊接构件在疲劳裂纹扩展过程中裂纹形状保持为半椭圆形状;针对桥梁构件实际受力特征,由钢桥梁构件的高周疲劳损伤演化方程入手,考虑初始裂纹条件下裂纹前缘的损伤区的存在及其对裂纹扩展的影响,采用虚拟裂纹扩张方法推导了适用于钢桥梁构件的疲劳裂纹扩展分析的疲劳裂纹扩展率公式,建议了裂纹扩展和疲劳寿命数值计算方法.采用文中的计算方法,研究了已有的钢桥梁结构焊接构件疲劳实验的裂纹扩展过程和疲劳寿命的计算.计算结果表明:裂纹的扩展过程中裂纹的深度和表面半长度之比a/c是一个变化的数值,且在一定的a0/t0条件下,随着a0/c0的增加,循环次数逐渐增大.     

潜艇锥柱结合壳焊趾表面裂纹疲劳寿命计算

随着潜艇用钢屈服强度的不断提高，潜艇耐压壳体的直径及锥壳的半锥角的不断加大，潜艇耐压壳体锥柱结合壳连接焊接焊趾处的疲劳寿命已越来越受到设计人员的重视，但目前还没有可靠的设计方法可以遵循。针对潜艇锥柱结合壳连接焊缝处的受力特点为压弯结合应力，在分析了平行于裂纹面的应力，曲率的约束以及液楔的作用对潜艇焊趾表面裂纹疲劳寿命的影响进行分析后认为，潜艇锥柱结合壳焊距表面裂纹疲劳寿命计算可以采用对压应力进行修正的应力强度因子计算模型。本文给出了对压应力进行修正的应力强度因子计算式，在此基础上提出了一套能考虑焊距的外应力集中以及爆接残余应力等影响的受压弯应力焊接结构焊趾裂纹疲劳寿命计算方法，对初始表面裂纹形状和大小对疲劳寿命的影响进行了系列计算，计算结果表明，本方法预报出的疲劳寿命与实验结果在量级上是吻合的，但在推向实用之前还需要做更多的实验验证。     

潜艇的先进制造技术与隐身性能

隐身性是提高潜艇战斗力和生命力的重要保障,低噪声和大潜深是潜艇隐身性的重要指标.本文从生产工艺的角度论述了降噪技术和增大潜深技术与先进制造技术的密切关系,提出了"总段模块化制造技术"和潜艇"精度制造技术"的设计思想,这对潜艇的设计以及制造工艺的提高具有重要的参考价值.     

33rd International Conference on Ocean,Offshore and Arctic Engineering （OMAE2014）

正San Francisco,California,June 8-13,2014.OMAE 2014 is the ideal forum for researchers,engineers,managers,technicians and students from the scientific and industrial communities from around the world to:·meet and present advances in technology and its scientific support;·to exchange ideas and experiences whilst promoting technological progress and its application in industry·to promote international cooperation in ocean,offshore and arctic engineering.In line with the tradition of excellence of previous OMAE conferences,more than 900 technical papers are planned for presentation.Outreach for Engineers Specialty Forum This Specialty Forum is designed for students and professionals who may not be familiar with the Ocean and Offshore industry,as well as those who have just recently specialized in this field.     

Errata

正In the paper"Influence of Fouling Assemblage on the Corrosion Behaviour of Mild Steel in the Coastal Waters of The Gulf of Mannar,India"in Vol.12,No.4,Page:509,References were lost,and the two authors’biographies were identical.The correct text is shown below.We apologize to the authors and our readers for any inconvenience caused by the errors.     

Journal of Marine Science and Application 2014 Sum. Contents

正~~     

联合作战计划和执行系统

全球指挥控制系统(GCCS)实施当前美国海军网络中心战信息基础设施的联合计划网络。联合作战计划和执行系统(JOPES)支持GCCS实现联合计划。JOPES有两类计划：时间不限的精密预案计划生成作战计划、方案计划或职能计划；时间敏感的危机行动计划生成作战命令或战役方案。前者在和平时期创建的作战计划是后者的计划基础，加速应付危机的能力。     

Recent progress on wave induced loading measurements in warships

Recent measurements of wave induced hull strain and flexure in RN warships are presented together with the derivation of the current design criteria for extreme hull girder bending loads. The history of the development of the shipboard instrumentation used is given and recent developments to improve the quality and ease of analysis of the data are described. An unexpectedly high transverse asymmetry in the longitudinal strains measured in destroyers is shown to be the result of a combination of vertical and lateral bending in oblique seas. Finally recent theoretical comparisons between the loading of Deep-Vee hulls and conventional UK rounded bilge hulls are presented which demonstrate the higher loading experienced by this type of hull form.     

The 11th International Conference on Hydrodynamics (ICHD 2014)

正19–24 October 2014 SingaporeCONFERENCE THEMES The overall aim of the ICHD Conference is to provide a forum for participants from around the world to review,discuss and present the latest developments in the broad discipline of hydrodynamics and fluid mechanics.The first International Conference on Hydrodynamics(ICHD)was initiated in 1994 in Wuxi,China.Since then,9 more ICHD conferences were held subsequently in Hong Kong,Seoul,Yokohama,Tainan,Perth,Ischia,Nantes,Shanghai and St Petersburg.Evidently the ICHD conference has become an important event among academics,researchers,engineers and operators,working in the fields closely related to the science and technology of hydrodynamics.The 11th ICHD will be held in Singapore in 2014.     

第十二届深水操作会议和展览会(英文)

正November 4-6,2014Moody Gardens HotelConvention Center/Galveston,TX The Deepwater Operations Conference and Exhibition is celebrating its 12th anniversary this year.This growing event will continue the tradition of excellence in addressing operational challenges involved in developing deepwater resources.We will return to the Moody Gardens Hotel and Convention Center on November 5-7,2014 in Galveston,Texas.     

Eastbound or westbound ?

In terms of equal sailing distances, where is the inflexion when ships depart from ports in the Asian Continent to New York via Suez and/or Panama？
The answer is China South Port Group （Hong Kong, Shenzhen and Guangzhou）.     

Impact of regulation on the performances of long-distance transport services: A comparison of the different approaches in Sweden and Norway

Despite the many socio-economic similarities between Sweden and Norway, differences in jurisdiction, organisation, cooperation, and financing of long-distance passenger train and coach services have led to the development of four distinctively different ways of serving the markets. This paper describes how the train and coach markets have developed in the two countries, with emphasis on regulatory and industrial structure and a couple of performance variables.Looking at passenger rail, both countries separated infrastructure from operation over a decade ago. However, while Norwegian rail is characterised by an almost monopoly supplier, rail services in Sweden are partly decentralised to the responsibility of county authorities and are widely subjected to competitive tendering. The rest of the network is about to be opened up for on-the-track competition. Swedish Rail (SJ) has spent the last decades consolidating its core business (passenger rail) and sold out its other businesses. In contrast, the Norwegian state rail (NSB) has expanded its business to become a major bus operator and property owner, with extensions also into the Swedish market.The coach industry was more recently deregulated in both countries. The Swedish coach market is dominated by privately owned companies operating services to and from Stockholm. In Norway, state-owned NSB is a major coach operator on medium distance routes, and is also the largest partner of Nor-Way Bussekspress which totally dominates long-distance coach services. Further, the Norwegian coach market is characterised by cross-ownership and cooperation which has enabled an extensive route network which covers most of Norway.We find distinct differences in achievements in the two modes and in the two countries. Swedish rail services have succeeded in winning market shares and in renewing and developing both infrastructure and service levels to a greater extent than the Norwegian model. On the other hand, the Norwegian coach market seems to be more developed and efficient compared to its Swedish counterpart.The paper concludes with a discussion on the possible links between the different approaches and the performance observed, with the aim to stimulate further and more detailed research on some important issues.     

某海港码头的撞损修复

依据码头撞击受损区域调查检测结果,对受损构件提出合理的修复方案,为码头的安全运行提供保障。