共查询到17条相似文献,搜索用时 203 毫秒
1.
文章建立了S型铺管船的船体、托管架和管线动态耦合模型。考虑了海浪、风和海流载荷作用下以及动力定位系统的控制下,分析时域内管道对船舶运动和受力特点的影响。主要包括:建立起重铺管船的动力定位运动模型,建立基于碰撞-接触原理的V型托辊和托管架模型,设计具有PID伺服系统的张紧器模型,提供连接托管架和船尾的非线性弹性铰接模型。进行时域动态模拟得到结果,通过与非铺管作业工况下的运动响应的对比表明,管线对船舶横摇运动影响较大,对纵摇和垂荡运动有一定程度的影响;管道对船舶纵荡、横荡和艏摇三个自由度上的受力影响极大。 相似文献
2.
3.
海底管道铺设过程的敏感性分析是海底管道安装设计的重要内容,通过海底管道铺设敏感性分析可以明确铺管作业的操作参数,为海上铺管作业提供支持,并有效识别铺管过程的潜在风险。采用铺管软件OFFPIPE建立海底管道铺设模型,对陆丰7-2海底管道铺设张力、水深和托管架角度等参数敏感性进行了分析,明确了蓝疆号铺管船的铺管作业参数,为安全可靠地铺设海底管道提供了技术支持。 相似文献
4.
深水海底管线的铺设主要采用S型铺管的方式,在铺管船船尾设有托管架以支撑和保护管道,并控制管道入水的角度,保证管道安全。依托某深水铺管船项目,根据S型管道的特点,将其分为上弯段、中间段和下弯段三部分进行力学分析;利用MATLAB软件编写程序,计算不同铺设工况下的管道形态和内力,以OFFPIPE的计算结果为参照,验证本程序的可靠性和准确性。针对在实际铺管过程中并不能保证管道与每个托辊都接触的问题,在程序中设定指定托辊不接触的情况。计算结果表明,该工况下管道在后一个托辊处将受到较大弯矩作用,可能引起失效,应引起关注。 相似文献
5.
6.
7.
8.
9.
10.
11.
In the deepwater S-lay operations depending on the required stinger radius and rollers configuration, relatively large plastic deformation is induced when the pipe passes over the stinger, under the combined loadings of bending, axial tension, roller reaction force and the pipelay vessel motion. The resulting plastic deformation does not vanish after the pipe leaves the stinger. It accumulates until the pipe reaches the seabed. The inherited residual deformation might reduce the collapse capacity of the pipe under the external pressure loading. The present paper investigates the dynamic loading history of the pipe during the S-lay operation based on a test-verified finite element model, and then calculates the residual plastic deformation of the pipe cross-section after the pipe reaches the seabed. Finally, the nonlinear collapse analysis is implemented based on the modified RIKS method to evaluate the capacity of the installation-induced deformed pipe. The results confirm that the deepwater S-lay operation will lead to obvious plastic deformation of the pipe, which decreases the pipe collapse capacity to some extent. 相似文献
12.
In deepwater S-lay operations, the combined influences of stinger curvature, axial tension and roller support force can induce very large plastic deformation in the pipe. Dynamic loads from vessel motion and pipe sliding down the stinger lead the cyclic plastic deformation. This paper investigates the cyclic plastic stress history of the overbend pipe subjected to the dynamic pipelaying loading. The dynamic roller support forces are obtained through an innovative large scale hybrid substructure experiment constructed to simulate the pipe-stinger impact behavior. The measured roller forces are used to verify a 3D finite element analysis results developed with ABAQUS/Standard to observe the dynamic pipe stress history. The results confirm that the roller support can induce stress concentration in the pipe and the combined dynamic pipelaying loadings can cause extensive cyclic plastic deformation. 相似文献
13.
14.
15.
在使用S型铺管法铺设海底管道过程中,位于托管架上的管道(简称为上弯段)因受到较大的张力、弯矩及托管架的支撑反力作用,容易发生局部屈曲破坏。文中将托管架简化为连续型和滚轮支撑型两种,对连续型托管架上的管道进行了理论研究,并利用非线性有限元方法模拟了滚轮支撑作用下海底管道的受力状态。然后以12英寸管道为例,将两种托管架上的管道应变分布进行了对比。结果表明在连续型托管架上管道应变是一条直线;而滚轮支撑托管架上应变为波浪线,在滚轮作用处较大,滚轮之间较小。而且,应变随着张力的增大而增大,随托管架半径的增大而减小。 相似文献
16.
采用ANSYS11.0研究深水海底管道铺设过程中管道变形及受力。针对海底管道铺设边界的特殊性,提出了边界处理的新方法。根据管道在触地点处所受海底反力为零的假设,利用ANSYS参数化设计语言(APDL)编程迭代,寻找出管道触地点;根据给定的托管架形式,迭代求出管道与托管架的分离点。利用pipe59单元模拟管道的大位移非线性变形,分析了张紧力、水平力、悬跨段弯矩、悬跨段长度及管道与托管架的分离角之间的关系,据此工程人员可以根据所要控制的悬跨段弯矩计算所需的张紧力和入水角。最后通过与OFFPIPE专用软件所得结果进行比较,说明方法的可行性与准确性。 相似文献
17.
综合考虑液压气柱的张力-冲程非线性关系、液压气柱与立管之间的夹角以及平台-张紧器-立管之间的耦合关系,研究顶张式立管液压气动式张紧器的不同模拟分析方法。选取3种典型工况,对不同张紧器模拟方法下立管的动态响应进行仿真计算,分析比较不同模拟方法的科学性和适用性。结果表明:在顶张式立管分析过程中,张紧器的合理模拟至关重要,是否考虑液压气柱和立管之间的夹角对立管响应的影响不大;恒定集中力模型不能反映立管张力的变化规律,而且立管响应也存在较大差别,故不宜采用;线性模型可用于平台运动幅值较小的情况;非线性模型最能反映张紧器的刚度特性,且在极端载荷环境下尤为适用。 相似文献