平地机安装自动找平系统的使用与校对

平地机被广泛应用于各种路面工程的平整及其它工程的改良施工中,介绍了平地机自动找平系统的组成、作用、控制,着重对系统的三大作用、校对时间作了说明.     

Correlation between automotive CO, HC, NO, and PM emission factors from on-road remote sensing: implications for inspection and maintenance programs

Carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NO) emission factors (EFs) are measured with a commercial vehicle emissions remote sensing system (VERSS) during a large-scale vehicle exhaust emissions study in Las Vegas. Particulate matter (PM) EFs are simultaneously measured for individual vehicles with a newly developed PM-VERSS based on ultraviolet backscatter light detection and ranging (Lidar). The effectiveness of CO and HC EFs as proxy for NO and PM EFs for spark-ignition vehicles is evaluated. Poor correlations were found between EFs for pollutants on an individual vehicle basis indicating that high EFs for one or more pollutants cannot be used as a predictor of high EFs for other pollutants. Stronger functional relationships became evident after averaging the EF data in bins based on rank-order of a single pollutant EF. Low overlap between the highest 10% emitters for CO, HC, NO, and PM was found. These results imply that for an effective reduction of the four pollutants, inspection and maintenance (I/M) programs, including clean screening, should measure all four pollutants individually. Fleet average CO and HC concentrations determined by gaseous VERSS were compared with fleet average CO and HC concentrations measured at low-idle and at high-idle during local I/M tests for spark-ignition vehicles. The fleet average CO concentrations measured by I/M tests at either idle were about half of those measured by remote sensing. The fleet average high-idle HC concentration measured by I/M tests was about half of that measured by VERSS while low-idle I/M and VERSS HC average concentrations were in better agreement. For a typical vehicle trip, most of the fuel is burned during non-idle conditions. I/M measurements collected during idling conditions may not be a good indicator of a vehicle’s potential to be a high emitter. VERSS measurements, when the vehicle is under a load, should more effectively identify high emitting vehicles that have a large contribution to the mobile emissions inventory.     

Spatial Dynamics of Multibody Tracked Vehicles Part II: Contact Forces and Simulation Results

In this part of the paper, three dimensional computational capabilities, that includes significant details, are developed for the nonlinear dynamic analysis of large scale spatial tracked vehicles. Three dimensional nonlinear contact force models that describe the interaction between the track links and the vehicle components such as the rollers, sprockets, and idlers as well as the interaction between the track links and the ground are developed and used to define the generalized contact forces associated with the vehicle generalized coordinates. Tangential friction and contact forces are developed in order to maintain the stability of the track motion and avoid the slippage of the track or its rotation as a rigid body. Body and surface coordinate systems are introduced in order to define the spatial contact conditions. The nonlinear equations of motion of the tracked vehicle are solved using the velocity transformation procedure developed in the first part of this paper. This procedure is used in order to obtain a minimum set of differential equations, and avoid the use of the iterative Newton-Raphson algorithm. A computer simulation of a tracked vehicle that consists of one hundred and six bodies and has one hundred and sixteen degrees of freedom is presented in order to demonstrate the use of the formulations presented in this study.     

Spatial Dynamics of Multibody Tracked Vehicles Part I: Spatial Equations of Motion

In this paper, the nonlinear dynamic equations of motion of the three dimensional multibody tracked vehicle systems are developed, taking into consideration the degrees of freedom of the track chains. To avoid the solution of a system of differential and algebraic equations, the recursive kinematic equations of the vehicle are expressed in terms of the independent joint coordinates. In order to take advantage of sparse matrix algorithms, the independent differential equations of the three dimensional tracked vehicles are obtained using the velocity transformation method. The Newton-Euler equations of the vehicle components are defined and used to obtain a sparse matrix structure for the system dynamic equations which are represented in terms of a set of redundant coordinates and the joint forces. The acceleration solution obtained by solving this system of equations is used to define the independent joint accelerations. The use of the recursive equations eliminates the need of using the iterative Newton-Raphson algorithm currently used in the augmented multibody formulations. The numerical difficulties that result from the use of such augmented formulations in the dynamic simulations of complex tracked vehicles are demonstrated. In this investigation, the tracked vehicle system is assumed to consist of three kinematically decoupled subsystems. The first subsystem consists of the chassis, the rollers, the sprockets, and the idlers, while the second and third subsystems consist of the tracks which are modeled as closed kinematic chains that consist of rigid links connected by revolute joints. The singular configurations of the closed kinematic chains of the tracks are also avoided by using a penalty function approach that defines the constraint forces at selected secondary joints of the tracks. The kinematic relationships of the rollers, idlers, and sprockets are expressed in terms of the coordinates of the chassis and the independent joint degrees of freedom, while the kinematic equations of the track links of a track chain are expressed in terms of the coordinates of a selected base link on the chain as well as the independent joint degrees of freedom. Singularities of the transformations of the base bodies are avoided by using Euler parameters. The nonlinear three dimensional contact forces that describe the interaction between the vehicle components as well as the results of the numerical simulations are presented in the second part of this paper.     

大跨径连续刚构桥的温度效应分析

以魏家洲特大桥为例,按照我国公路桥涵设计规范、英国BS5400规范、新西兰规范确定不同的计算模式,对大跨径连续刚构桥进行温度效应分析,得出：温度应力在大跨径连续刚构桥整个桥梁设计中占有很大的比重,且采用不同的温度梯度计算模式,所得到的梁内温度应力值相差较大,甚至出现异号的温度应力.     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).     

Exploring the impact of walk–bike infrastructure,safety perception,and built-environment on active transportation mode choice: a random parameter model using New York City commuter data

This study estimates a random parameter (mixed) logit model for active transportation (walk and bicycle) choices for work trips in the New York City (using 2010–2011 Regional Household Travel Survey Data). We explored the effects of traffic safety, walk–bike network facilities, and land use attributes on walk and bicycle mode choice decision in the New York City for home-to-work commute. Applying the flexible econometric structure of random parameter models, we capture the heterogeneity in the decision making process and simulate scenarios considering improvement in walk–bike infrastructure such as sidewalk width and length of bike lane. Our results indicate that increasing sidewalk width, total length of bike lane, and proportion of protected bike lane will increase the likelihood of more people taking active transportation mode This suggests that the local authorities and planning agencies to invest more on building and maintaining the infrastructure for pedestrians. Further, improvement in traffic safety by reducing traffic crashes involving pedestrians and bicyclists, will increase the likelihood of taking active transportation modes. Our results also show positive correlation between number of non-motorized trips by the other family members and the likelihood to choose active transportation mode. The model would be an essential tool to estimate the impact of improving traffic safety and walk–bike infrastructure which will assist in investment decision making.     

Time Gap Modeling under Mixed Traffic Condition: A Statistical Analysis

This paper attempts to model vehicular time gap, which is defined as the time interval between any two successive arrivals of vehicles at a reference point of measurement on a road segment. Such an approach is justified under the non-lane-based heterogeneous traffic conditions prevailing in developing countries such as India, characterized by many “zero” time gaps due to simultaneous arrivals within a given road width. In addition, time gap data are characterized by a significant amount of data in the tail region due to long headways. Nevertheless, many researchers of time gap modeling have used light-tailed distributions that modeled time gaps satisfactorily due to two reasons: (a) The tail data was merged into a single bin; and (b) goodness-of-fit tests such as the Chi-square test, which has many limitations, were used. Further, some researchers have suggested different distributions for the same range of traffic flows, leading to ambiguity in distribution selection. In addition, bin size, which dictates the degree of fit of any distribution, has been ascribed very less importance in time gap modeling. Hence, this paper tries to consolidate and standardize the existing research in time gap modeling research by addressing all these issues. Two new distributions, namely Generalized Pareto (GP) and Generalized Extreme Value (GEV) with better tail modeling properties, have been proposed along with other conventional distribution to model vehicular time gaps over a wide range of flow from 550 vph to 4,100 vph. Two types of goodness-of-fit tests, namely Area-based and Distance-based tests, have been used. It has been found from the study that GP distribution fits the time gap data well (overall and tails) up to a flow range of 1,500 vph based on both kinds of tests, and GEV fits the data well for the flow levels above 1,500 vph based on the area test only.