基于Ansys的矩形加筋平盖封头强度评定

将有限元方法与分析设计相结合,利用有限元分析软件Ansys对一种矩形加筋平盖封头进行强度评定。本文首先介绍瓶盖封头结构的改进。然后建立有限元模型,并进行应力求解。结果表明,此加筋平盖封头满足强度要求,与普通平盖封头相比,减小了平盖的厚度,降低了结构总重量,对平盖封头的结构改进设计具有一定指导作用。     

基于深度强化学习的智能船舶航迹跟踪控制

[目的]智能船舶的航迹跟踪控制问题往往面临着控制环境复杂、控制器稳定性不高以及大量的算法计算等问题。为实现对航迹跟踪的精准控制,提出一种引入深度强化学习技术的航向控制器。[方法]首先,结合视线(LOS)算法制导,以船舶的操纵特性和控制要求为基础,将航迹跟踪问题建模成马尔可夫决策过程,设计其状态空间、动作空间、奖励函数;然后,使用深度确定性策略梯度(DDPG)算法作为控制器的实现,采用离线学习方法对控制器进行训练;最后,将训练完成的控制器与BP-PID控制器进行对比研究,分析控制效果。[结果]仿真结果表明,设计的深度强化学习控制器可以从训练学习过程中快速收敛达到控制要求,训练后的网络与BP-PID控制器相比跟踪迅速,具有偏航误差小、舵角变化频率小等优点。[结论]研究成果可为智能船舶航迹跟踪控制提供参考。     

Development of knowledge based body structure concept design model

The purpose of this study is to propose a concept design process for an automotive body structure using technical information on the major joints and members of vehicles. First, in order to collect the technical information on major joints and members, 17 vehicles were selected using benchmark data. The collected technical information for the selected vehicles was the cross sectional shapes of each joint and member which were used for the analysis of joint stiffness, crashworthiness and static stiffness of the member to make a database along with cross section properties. This study applied a ‘What If Study’ technique to perform a concept design of an automotive body using the analyzed information and selected cross section meeting the design objectives. The criteria for the selection of the cross section were defined by subdividing the defined design objectives of an automotive body structure and constraints into members and joints. In order to configure an analysis model of an automotive body structure using the selected cross section, a shape parametric model was used and static stiffness, dynamic stiffness and crashworthiness were assessed to evaluate the configured automotive body structure. The evaluation result showed that the crashworthiness and static/dynamic stiffness were improved compared to an existing body structure. In addition, the weight of the body structure was reduced. Through this study, the process that can rapidly and effectively derive and evaluate the concept design of an automotive body structure was defined. It is expected that, henceforth, this process will be helpful for the study of automotive body structures.     

Nanoparticle emission characteristics and reduction strategies by boost pressure control and injection strategies in a passenger diesel engine

This research attempted to analyze nanoparticles and other harmful exhaust emissions in accordance with injection strategies and air-fuel ratio (AFR) changes for small diesel engines. The emission characteristics were analyzed in the medium-speed condition, which is the main driving range of a diesel engine. In the case of particulate matter (PM), the number of particles was measured, analyzed, and compared to identify the correlation and emission characteristics of nanoparticles by using a dilution device and condensation particle counter (CPC), which are international standards for particle measurement recommended by the Particulate Measurement Programme (PMP). The engine torque tended to be reduced as pilot injections were added, and the torque was increased by the increased boost pressure, but reduced by the exhaust pressure increase in a part of the low-load range. The number of nanoparticles was not influenced greatly by the change in AFR, but the reduction effect on the PM weight was great depending on the boost pressure increase. In addition, the number of nanoparticles tended to increase as the fuel injection timing became closer to TDC in all conditions, and its difference became larger with an increase in AFR. In addition, in the case of the pilot injection, nanoparticle emission showed similar characteristics depending on the main injection timing, but it was increased by advanced injection timing when performing the main injection only, and the number of the nanoparticles increased as pilot injections were added. Last, the optimal conditions for EMS calibration were analyzed by selecting the conditions of torque reduction and NOx increase within 5 % from all of the engine operating conditions; optimized conditions are presented.     

船舶上层建筑重量重心对其固有频率的影响

在船舶设计、建造过程中及船舶建造完成后,有时上层建筑的固有频率与主机、螺旋桨的激励频率相接近。想要通过一些简单有效的手段对船舶进行修改,使上层建筑的固有频率避开激励源频率以避免共振。本文利用大型通用有限元分析软件Ansys,以某300,000吨级原油船为研究对象,对上层建筑的重量和重心高度如何影响上层建筑的首阶横向、纵向固有频率进行灵敏度分析,以求找到简单有效的、适于工程实际中改变船舶上层建筑固有频率的方法。     

高速公路直线路段突起路标间隔设置方法

基于驾驶人的视觉惰性、视觉警示频率和感觉特性,分析了突起路标的视觉警示作用,确定了突起路标的闪现频率,计算与修正了突起路标的初始间隔。应用ADAMS/Car仿真软件模块,建立了道路、车辆和突起路标模型,将车型设置为大型车和小型车,大型车的车速设置为60、80、100km·h-1,小型车的车速设置为80、100、120km·h-1,大型车和小型车的方向盘转角均设置为1°、3°、5°。分别对提出的12m间隔与现行规范推荐的15m间隔各进行243次仿真,分析振动警示效果。仿真结果表明:在12m间隔下,平均碾压率为93.1%,小型车和大型车对应的平均警示率分别为41.7%和5.6%;在15m间隔下,平均碾压率为93.7%,小型车和大型车对应的平均警示率分别为33.3%和28.9%;12、15m间隔对小型车都具有较好的振动警示效果,15m间隔对大型车的振动警示效果更好。当高速公路夜间交通流较大或需要加大交通设施的夜间安全效果时,可选12m间隔提供良好的视觉连续性和视觉警示效果;考虑施工维护的方便性和经济性或者大型车比例较大时,可选择15m间隔。     

38000 m3特种工程船的波浪载荷预报和正确计算

基于三维势流理论,应用DNV-SESAM软件,对某特种工程船在规则波中不同浪向角下的波浪载荷传递函数进行了计算.分别使用东海、南海、渤海、南美洲及北大西洋五个海域的海况数据,对该船的调遣工况和作业工况进行了垂向波浪弯矩和剪力的长期预报.最后将所得的长期预报结果与CCS规范值进行了比较.     

探究公路勘察设计与环境保护的关联

文章首先分析了公路建设过程中对环境造成的影响,而后阐述了公路工程在路线设计时应注意的环境问题,最后列举了提升公路设计线路与环境环保的举措,希望降低工程在建设过程中对环保造成的不利影响。