Operating speed pattern optimization of railway vehicles with differential evolution algorithm

The railway transportation system has much advantage in eco-friendliness, punctuality and safety compared to any other transportation system. Most of the railway system administrators have to control and operate under limited resources such as trains and facilities. It is necessary to control traveling time and energy consumption for efficient operation in the railway systems, because the board rate of passenger is inconstant with time variance. It is common that the shorter traveling time causes the greater energy consumption. In this study, a new optimization method considering operation time or energy consumption is proposed by using differential evolution algorithm and some cases are reviewed. The total energy change due to operation time variation are investigated by using the proposed optimization method for tangent and gradient track conditions. Both cases, the total energy decreases exponentially. However, because of gradient the total energy are saturated after a certain time for gradient track.     

Full scale ice sea trials of Korean ice breaking research vessel ‘Araon’ on the big floes near Antarctica

A speed sea trial was performed in the Amundsen Sea in February and March of 2012. The Korean ice breaking research vessel “Araon” was used to check speed performance on the big floes. Two of ice trial cases were carried out. We describe the time history of location, the engine power, and the revolutions per minute during the ice trial, and the trajectory of the ship. Additionally, the measured ice properties are considered and discussed. The ice trial results were analyzed according to variation in ice thicknesses, ice strength, propulsion power, and the speed level of the ship. Our analysis results are compared to model test results and ice trial results. A correction to the target ice thickness was used to compare the power and speed relation in the same ice thickness because it is easy to know the relative speed performance of the ship. The Hamburgische Schiffbau-Versuchs Anstalt method was applied for the correction. The speed of Araon in big floes was higher than the speed in level ice. The speed after the correction at 10 MW of power and 103 cm of ice thickness was 5.4 knots based on analysis results.     

Fatigue life prediction of a rubber material based on dynamic crack growth considering shear effect

This paper suggests a fatigue life calculation method (A fatigue life calculation method is suggested) for rubber components based on the dynamic crack growth considering shear effect. Dynamic tearing tests were carried out, and the crack length was measured using an optical microscope to calculate the dynamic crack growth rate which characterizes and determines the fatigue life. The algorithm was numerically implemented in finite element code, ABAQUS standard, by using the user subroutine and applied to several rubber components. In the finite element analysis, deformation mode of an element was classified into tension and shear, and a weighting factor was multiplied to a strain energy density according to the degree of shear strain. Tension and compression of an elliptic dumbbell specimen was simulated in order to verify the material parameters of the suggested fatigue life prediction equation and to enhance the reliability of the algorithm. Finally, the fatigue life of a vehicle suspension bushing was calculated and compared with test. There were good agreements in the failure location and the magnitude of the fatigue life.     

Node-based scheduling method for easy migration from CAN to FlexRay in in-vehicle networking systems

As vehicles become more intelligent, in-vehicle networking (IVN) systems such as controller area network (CAN) are essential for the convenience and safety of drivers. To expand the applicability of IVN systems, attention is currently being focused on chassis networking systems that require increased network capacity and real-time capabilities. FlexRay was developed to replace CAN protocol in chassis networking systems, to remedy the shortage of transmission capacity and unsatisfactory real-time transmission delay of conventional CAN. However, FlexRay network systems require a complex scheduling method, which is a barrier to their implementation as chassis networking systems. In particular, if we want to migrate from a CAN network to a FlexRay network using the well-defined CAN message database, which has been specifically constructed for chassis networking systems by automotive vendors, a new type of scheduling method is necessary to reduce scheduling efforts during the software development process. This paper presents a node-based scheduling method for easy migration from a CAN network to a FlexRay network system. To demonstrate the feasibility of the technique, its performance is evaluated in terms of various software complexity indices.     

Comparison study on characteristics of nano-sized particle number distribution by using condensation particle counter calibrated with spray and soot type particle generation methods

In the year 2011, the Particle Measurement Program (PMP) in Europe started the regulation of the diesel vehicle’s nano-sized particle number density (PN) due to its high degree of harm to the human body. Concretely, the standard level of PN emission was introduced in the Euro 5+ and 6 emissions regulation with a limit (<6.0 × 10¹¹#/km) for diesel light-duty vehicle. Therefore, the determination of suitable and sophisticated instruments for reliable particle sampling and analysis was essential in taking exact experimental data. Now, among the PN emission measuring devices suggested by the PMP, condensation particle counter (CPC) is a key equipment for measuring the particle number density in real time and it has been used extensively. However, CPC can cause different results depending on operating conditions of the saturator and condensation that induce different rates of particle growth. This study was conducted to analyze the effect of CPC calibrated by a two-particle generator with spray and soot type methods applied on the nano-sized particle distribution’s parameters such as number concentration and linearity. Also, in order to ensure the reliability for particle sensor system named as PPS, which had emerged as a useful diagnostic to making spatially and temporally resolved quantitative measurements of diesel PN concentration, it was compared with calibrated CPC system. As a result, nano-sized particle measuring system with CPC calibrated by spray type particle generator had a much higher counting efficiency, indicating a larger nano size available than soot type particle generator. And, comparative experimental results on the correlation between the particle number of CPC to a reflectance PPS system showed that above 5,000 #/cm ³ in number concentrations measured by CPC as well as PPS were found to be similar with good linear relationship.     

Vehicle velocity estimation using effective inertia for an in-wheel electric vehicle

In this study, a vehicle velocity estimation algorithm for an in-wheel electric vehicle is proposed. This algorithm estimates the vehicle velocity using the concept of effective inertia, which is based on the motor torque, the angular velocity of each wheel and vehicle acceleration. Effective inertia is a virtual mass that changes according to the state of a vehicle, such as acceleration, deceleration, turning or driving on a low friction road. The performance of the proposed vehicle velocity estimation algorithm was verified in various conditions that included straight driving, circle driving and low friction road driving using the in-wheel electric vehicle that was equipped with an in-wheel system in each of its rear wheels.     

Evaluation and visualization of stratified ultra-lean combustion characteristics in a spray-guided type gasoline direct-injection engine

To comply with reinforced emission regulations for harmful exhaust gases, including carbon dioxide (CO₂) emitted as a greenhouse gas, improved technologies for reducing CO₂ and fuel consumption are being developed. Stable lean combustion, which has the advantage of improved fuel economy and reduced emission levels, can be achieved using a sprayguided-type direct-injection (DI) combustion system. The system comprises a centrally mounted injector and closely positioned spark plugs, which ensure the combustion reliability of a stratified mixture under ultra-lean conditions. The aim of this study is to investigate the combustion and emission characteristics of a lean-burn gasoline DI engine. At an excess air ratio of 4.0, approximately 23% improvement in fuel economy was achieved through optimal event timing, which was delayed for injection and advanced for ignition, compared to that under stoichiometric conditions, while NO_x and HC emissions increased. The combustion characteristics of a stratified mixture in a spray-guided-type DI system were similar to those in DI diesel engines, resulting in smoke generation and difficulty in three-way catalystutilization. Although a different operating strategy might decrease fuel consumption, it will not be helpful in reducing NO_x and smoke emissions; therefore, alternatives should be pursued to achieve compliance with emission regulations.     

Simulation of flow in diesel particulate filter system using metal fiber filter media

Metal fiber is introduced as a new filter media in wall-flow Diesel Particulate Filter (DPF) system. This technology has high temperature durability which is required for filter regeneration, and can maintain the mechanical strength even in the extreme exhaust-related vibrations of vehicles. However, the regeneration near the wall (outer layer) is more difficult because of the heat loss and reduced gas flow near the wall. In this study, a flow is simulated to determine the flow control method for the more uniform flow in all filter layer. By using Star CCM+ commercial software, we obtain local velocity, streamline, and pressure distributions in the filter, which are typically difficult to obtain from measurements. The major control factors are the filter porosity, size and location of the distribution plate, and the number of blades of the swirler. By placing the distribution plate in front of the filter, the flow velocity near the wall was increased. The optimum location and size of the flat plate were chosen. By attaching the blade on the plate the flow velocity near the wall was increased more. Therefore, the regeneration efficiency is increased by using the swirler-type metal fiber DPF system.