横向磁场直线开关磁阻电机换相位置的间接检测方法

针对横向磁场直线开关磁阻电机(TFLSRM)的结构,利用各相绕组磁链在磁极中随位置不同而产生的差异,提出了一种TFLSRM换相位置间接检测方法。该方法只需在初级边附加一套具有独立磁路的三相检测绕组,即可获得各相换相位置参考点,并能克服电机启动前各检测绕组磁链恒定不变而无法确定上升区与下降区的不足。结果表明,所提方法可方便地实现对TFLSRM换相位置的检测。     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

Determination of Critical Slip Surface of Soil Slope

A new complex method is presented considering not only the improvement upon the ＂bad ＂design point, but also the diversity of the newly generated complex, which is obtained by replacing the ＂bad ＂design point with the better design point located at the line between the ＂bad ＂design point and the ceotroid of the remaining design points of the old complex. The new complex method is applied to searching for the critical slip surface of two non-homogeneous soil slopes. The comparison of the results obtained by the new complex method with that by the basic complex method shows that the new complex method is much more likely to find the true critical surface for the randomly generated initial complex.     

AIP潜艇燃料电池供氢新技术--硼氢化钠水解制氢

氢源是目前移动式燃料电池技术研究和应用的瓶颈之一。本文介绍了AIP潜艇动力对燃料电池供氢技术的特殊要求和世界各国艇用氢源的研究进展,阐述了硼氢化钠水解制氢技术的工作原理和在潜艇环境下应用该供氢技术的优点,并在深入调研该技术的研究进展基础上,提出了将该制氢技术应用于我国AIP潜艇的设想。     

东营黄河大桥上部结构施工支架及挂篮关键技术

东营黄河大桥主桥上部结构(116 200 220 200 116)m预应力混凝土刚构连续结合梁的箱梁采用菱形挂篮悬臂施工法。介绍了主墩和次主墩0号块施工分别选取的支架方案,以及现浇直线段的支架方案。阐述了挂篮的试压方法,并对其试压结果进行了分析。     

基于ANN星识别算法的仿真平台

星敏感器是一种高精确度的姿态测量仪器，它通过对观测到的星点进行识别来计算姿态。为了能够较好地测试和验证星识别系统的性能，设计了一个基于ANN算法的星识别仿真平台。通过对该星识别仿真平台性能的测试，表明该仿真平台能够方便，实时地测试星识别算法的性能与正确性，因此说它是一种具有较好实用价值的星识别仿真平台。     

刚性悬挂移动式接触网施工技术浅谈

从施工的角度介绍了刚性悬挂移动式接触网的结构组成、移动原理、施工技术、施工制点,研究了施工测量、安装计算、导线架设、悬挂调整等环节对工程质量的影响,描述了移动式接触网系统在电气化铁道特殊场所的运用前景.     

施工图设计-施工总承包模式在铁路建设中的应用研究

工程总承包是目前国际上流行的项目管理模式。铁路建设推行施工图设计-施工总承包模式,实现业主与总承包商签订施工图设计和施工合同,施工图设计和施工同时进行,统筹安排和优化,总体控制项目造价。推进铁路建设施工图设计-施工总承包模式,国家及铁道部应建立和完善有关的法律法规与规章,借鉴国内外经验,使工程总承包模式更加规范化、标准化、多样化。     

洛卢公路洛河大桥设计简介

介绍了洛卢公路洛河大桥所采用的技术标准、桥型、截面型式及结构计算,并介绍了该桥设计在构造上所做的特殊处理及施工要点。     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)