桥梁混凝土水管冷却温度场有限元分析

针对混凝土水管冷却温度场的计算问题，分析了当前冷却水管有限元分析的主要方法，对多重网格法进行有效的处理，从而在不增加计算时间的前提下能更准确地计算出水管冷却温度场。基于这种处理方法，结合通用软件ANSYS对某高墩大跨刚构桥桥墩混凝土水管冷却温度场进行了仿真分析，计算结果与实测数据比较表明该方法计算精度是较高的。     

Effects of economic disincentives on private car use

A field experiment was conducted to investigate the effects of economic disincentives on private car use. Eighty two-adult households who were owners of at least one car were randomly assigned to three experimental groups and one control group. Both experimental and control groups logged their car trips during one week before, one week during, and one week after treatment. The treatment consisted of charging two of the experimental groups approximately 100% of normal cost per kilometer of driving during 2 weeks, and charging the third experimental group this amount per kilometer of driving during 4 weeks. With the purpose of investigating whether deliberate planning increases the effect of economic disincentives, the households in one of the former and in the latter group were asked to fill out a prospective car log for the following week. The control group was not charged or requested to fill out a prospective car log but was in other respects treated in the same way. Analyses of the car logs and odometer readings during and at the end of treatment showed a weak reduction of car use due to the economic disincentives that however were almost completely dependent on planning.     

汽车噪声测量的声场空间变换方法及其应用

降低汽车噪声的前提条件是准确确定噪声源位置及声强等参数，声场空间变换方法是确定噪声源位置的一种较好方法，阐述了声场空间变换的理论基础及基本原理，给出了应用实例，并对应用效果进行了分析。     

砂卵石地层台阶法施工隧道围岩-支护结构应力应变特性三维离散元分析

为了解砂卵石地层隧道围岩和支护结构的应力应变特性，以青海循隆高速公伯峡隧道为依托，借助PFC3D离散元软件对公伯峡隧道穿越砂卵石地层进行三维模拟，重点研究以密排短管棚预支护为根本前提，以三台阶预留核心土为施工方法的砂卵石地层围岩和支护结构的应力应变特性，并与现场实测进行对比分析。研究结果表明： 隧道台阶开挖时，围岩应力集中范围逐渐从拱顶过渡到拱腰，直到拱脚，对应的塑性区范围不断扩大，且密排短管棚对塑性区的发展有一定的“遮拦效应”； 围岩横纵向变形规律一致，主要是向隧道临空面产生收敛变形，且密排短管棚形成的梁拱效应限制了掌子面前方位移发展； 2种方法得到的初期支护变形规律一致，均呈阶段性变化，拱顶下沉累计值大于周边收敛累计值，且两者的最终变形量均满足规范限值要求。     

磁测式船舶姿态自动测量装置研究

利用三维磁传感器直接敏感在同状态下两个不同坐标系中的船舶综合磁场三维磁感应强度,研制了出一种新型的船舶姿态实时测量系统,并对该系统的测量原理,误差分析,校正原理与方法等作了较全面的论述。     

平面斜交联络通道水平冻结及实测分析

为解决常州地铁1号线翠竹站-常州火车站区间隧道联络通道因预留钢管片错环造成联络通道平面斜交的问题,采用Z字 型联络通道结构方案及平面斜交联络通道冻结加固方案,对冻结全过程进行温度与变形实测,分析其冻结温度场发展规律以及因 冻胀引起的地表位移变化规律。 得出以下结论: 1)因加强冻结孔的加强作用,其变化规律与常规直交联络通道有所区别; 2)下行 线左侧外侧测温孔外部测点降温速率比内部测点快,而内侧测温孔内部测点降温速率比外部测点快,下行线右侧恰好相反; 3)下 行线左、右侧测温孔开挖时温度回升的测点分别为外部测点与内部测点; 4)联络通道地表隆起最大值分布线亦倾斜,其最大倾角 约为36.2°,与联络通道倾角相近。     

场地平整的设计方法初探

场地平整设计已成为许多开发区招商引资的先决条件,决定着开发区域的开发强度、出地率、开发成本、土石方平衡等诸多因素。针对场地平整设计的方法及设计要点进行了初步探讨,有关经验可供相关专业人员参考。     

某电动汽车低频电场发射分析与优化

介绍某电动汽车低频电场发射的优化过程。采用近场扫描法及排除法,确定电机控制器是造成电场发射超标的干扰源,并明确干扰的传播路径。通过增加电机控制器的滤波电路,优化车辆搭铁和线束屏蔽设计,车辆低频电场发射满足了GB/T18387-2017要求。     

天津海河隧道泡沫-水喷雾系统保温措施升级及改造

海河隧道泡沫-水喷雾系统在冬季寒冷条件下运行时，个别雨淋阀组出现局部结冰的现象，对隧道的安全运行造成一定影响。针对这一运营难题，通过现场实测温度及数据分析，对箱体保温进行散热量计算并实测加热功率，对隧道内不同部位的雨淋阀组制定不同的保温措施。得出如下结论： 1）寒冷地区隧道的泡沫-水喷雾系统雨淋阀组应考虑保温。 2）雨淋阀组的保温措施应结合实际情况，根据箱外温度，制定对应的保温措施。 3）洞口位置的雨淋阀组应设置电加热器保温。 4）设置电加热器的雨淋阀箱体，其热量损失与隧道内温度成反比；温度越低，散热量越大，能耗越大。     

Flow-field guided steering control for rigid autonomous ground vehicles in low-speed manoeuvring

ABSTRACT

This paper studies the low-speed manoeuvring problem for autono-mous ground vehicles operating in complex static environments. Making use of the intrinsic property of a fluid to naturally find its way to an outflow destination, a novel guidance method is proposed. In this approach, a reference flow field is calculated numerically through Computational Fluid Dynamics, based on which both the reference path topology and the steering reference to achieve the path are derived in a single process. Steering control considers three constraints: obstacle and boundary avoidance, rigidity of the vehicle, plus the non-holonomic velocity constraints due to the steering system. The influences of the parameters used during the flow field simulation and the control algorithm are discussed through numerical cases. A divergency field is defined to evaluate the quality of the flow field in guiding the vehicle. This is used to identify any problematic branching features of the flow, and control is adapted in the neighbourhood of such branching features to resolve possible ambiguities in the control reference. Results demonstrate the effectiveness of the method in finding smooth and feasible motion paths, even in complex environments.