船体板格极限强度数值计算影响因素及敏感分析

船体板格极限强度的有限元计算方法应用广泛,但其计算方法具有一定的不稳定性,计算结果受多种因素的影响.本文针对船体板格有限元计算方法的不稳定性进行研究,通过将有限元计算结果与其他学者的研究成果进行对比,验证本文所采用的有限元方法的可靠性,然后针对板格材料、初始缺陷、网格密度、边界条件等几种因素的敏感性进行具体研究,发现理想应力应变关系会使得结果偏于危险.网格形状和网格密度对于结果均有影响,边界条件对于有限元结果有影响,最大误差在7.2%,并且模型3会使得结果偏于危险.初始缺陷是一敏感因素,最大误差在20%,因此需要根据实际缺陷选取合适的屈曲模态和比例因子.     

型腔结构对尾轴承力学性能影响的有限元分析

型腔尺寸的大小和腔数对水润滑橡胶尾轴承的力学性能有重要影响，并且直接影响轴承的承载能力和运转精度。本文基于有限元法，研究了不同型腔数目、型腔全角和型腔长度对尾轴承的力学性能影响。结果表明：在5种不同腔数尾轴承的研究对比中发现，4腔尾轴承的力学性能最优。研究型腔全角和长度因素影响时，发现全角55°长度500 mm的型腔结构性能更好。     

一种用于动力传动系统的橡胶隔振器优化设计研究

研究并设计一种橡胶隔振器,以减弱动力传动系统对船体的作用力.分析系统的工作原理,建立系统的动力学分析模型,得到系统的初始参数.氯丁橡胶的材料特性用Mooney-Rivlin模型描述,模型的系数C01和C10由橡胶材料的静态特性试验得到.根据动力传动系统的实际状态,设计隔振器的基本尺寸、基本参数,在此基础上,设计优化算法,其中,变量是螺栓预紧力、橡胶元件的尺寸、连接板之间的距离、橡胶和金属材料的最大VON MISES应力,目标函数是隔振器的刚度,数值仿真计算采用的是非线性有限元法,最后确定了满足隔振和使用要求、结构形式最优的隔振器.     

铁路预应力路堤加固技术数值研究

研究目的:铁路预应力路堤在国内外尚属一种新型路基加固法,其受力变形特性暂未得到系统化研究,相关加固设计理论仍处于探索性阶段。因此,有必要通过数值手段了解预应力路堤的工作状态,以掌握其加固性能。鉴于此,借助ABAQUS软件平台构建预应力路堤仿真系统,分析差异化预应力加固参数对路堤变形和承载能力的影响以及预应力加固构件的受力特征。研究结论:(1)路堤本体段坡面较优加固位置为距本体顶面以下0.3倍本体高度处;(2)坡率1∶1的预应力路堤在第1、2排侧压板分别施加50 k Pa、100 k Pa预压荷载时,其变形与承载力均可达传统路堤(坡率1∶1.5)水平,并可通过提升加固标准进一步强化路堤承载性能;(3)当对第1、2、3排侧压板分别施加50 k Pa、100 k Pa、100 k Pa预压荷载时,路堤内部附加围压S11>13.5 k Pa区域大致呈"x"形分布并形成横贯路堤的"预压加固区";(4)侧压板锚固区受力集中且复杂,应注意保障锚固区板体强度;(5)力筋在路堤加载前后的应力变化量与坡面侧向变形特征相关;(6)本研究成果可为铁路预应力路堤的加固设计提供技术指导。     

基于隧道检测钢筋分布不均状况下判定衬砌结构安全性应用研究

近年来隧道内出现的越来越多的质量安全事故,引起各方高度重视,相应的最适宜隧道主体工程衬砌质量控制的地质雷达无损检测方法被广泛应用。通过雷达无损检测可揭露出衬砌内欠厚、脱空、钢筋分布不均等大量各类型缺陷,针对欠厚脱空等缺陷制定的注浆或开窗等治理措施是目前工程中常见的整改闭合工序,但钢筋分布不均对结构安全影响如何判定,怎么界定处理尚无成熟方案与规定。本文针对隧道项目中实际检测出的钢筋分布不均缺陷,在不宜大范围扰动结构及围岩进行整治的情况下,以及在避免其他问题共存等不利因素的前提下,应用有限元数值模拟计算分析强度安全系数,并结合现场外观等综合因素对衬砌结构安全性进行分析判定研究。     

Preliminary investigation of PM1, PM2.5, PM10 and its metal elemental composition in tunnels at a subway station in Shanghai,China

In this study, real-time monitoring campaigns were conducted in two tunnels (Line A and Line B) at a subway station in Shanghai, including temperature, relative humidity, PM₁, PM_2.5 and PM₁₀, in order to understand the climate and PM characteristics in the transportation microenvironment. In addition, collected floor dust particles in the tunnel were analyzed by ICP for their metal elemental composition. Strong correlations occurred between all PM levels and meteorological parameters in the tunnel of Line A (with platform screen doors), in comparison with the weak correlations between such parameters in the tunnel of Line B (without platform screen doors). PM_2.5 and PM₁₀ between peak hours and off-peak hours for both lines presented significant differences (p < 0.05), respectively. Nevertheless, PM₁ showed a different pattern, with p > 0.05 for Line A and p < 0.05 for Line B, respectively. In addition, statistical results concluded that PM had an evident weekly variation for both lines. Friday was the highest day of all particulate matters in monitoring periods for both lines. Ratios of PM₁/PM₁₀ and PM_2.5/PM₁₀ were high when trains were out of service and low when trains were in service. Relative abundance of metal elements detected from floor dust particles proved that floor dust particles in tunnels might be a major source of airborne PM in the subway microenvironments, with Fe as the most abundant metal element, followed by Ca, Al, Mg, Mn, Zn, Cu, Cr, Ni, Pb and Hg.     

超声冲击处理对高强钢焊接接头残余应力影响的数值模拟

超声冲击处理(UIT)是一种有效的焊后改善焊接接头疲劳性能的工艺措施,其借助机械撞击和超声振动的共同作用,使焊趾表面产生塑性变形从而引入有益的压缩残余应力。为评价UIT技术对焊接接头残余应力的影响,该文提出了一套新的数值分析方法,包括焊接数值模拟及随后的超声冲击处理过程的动态弹塑性有限元分析。在有限元模型中考虑了实际的工艺参数和超声促成的材料软化效应。以船用高强钢AH36非承载十字焊接接头为研究对象,将预测的超声冲击处理前后的残余应力分布与实验结果进行对比,两者有较好的吻合。在此基础上,探讨了静态预载荷对超声冲击处理态残余应力再分布的影响。     

Optimal joint distance and time toll for cordon-based congestion pricing

This paper addresses the optimal toll design problem for the cordon-based congestion pricing scheme, where both a time-toll and a nonlinear distance-toll (i.e., joint distance and time toll) are levied for each network user’s trip in a pricing cordon. The users’ route choice behaviour is assumed to follow the Logit-based stochastic user equilibrium (SUE). We first propose a link-based convex programming model for the Logit-based SUE problem with a joint distance and time toll pattern. A mathematical program with equilibrium constraints (MPEC) is developed to formulate the optimal joint distance and time toll design problem. The developed MPEC model is equivalently transformed into a semi-infinite programming (SIP) model. A global optimization method named Incremental Constraint Method (ICM) is designed for solving the SIP model. Finally, two numerical examples are used to assess the proposed methodology.     

三边长后方交会在精密测量工程中的应用

文章以广西贵港西江航运建设二期工程船闸安全监测项目为例,介绍了三边长后方交会法的基本原理,推导出三边长后方交会法的坐标计算、平差公式等,分析了其误差来源和控制措施,论证了三边长后方交会在精密测量工程中的可行性与优越性。     

Travel time estimation oriented freeway sensor placement problem considering sensor failure

Optimal sensor placement on freeway corridor is of great interest to transportation authorities. However, current traffic sensors are easily subject to various failures. Therefore, it is necessary to incorporate sensor failure into the optimal sensor placement model. In this article, a two-stage stochastic model is proposed for the purpose of travel time estimation on freeway corridor. To balance the effectiveness and reliability, a stochastic conditional value at risk (CVaR) model is also proposed. Since both models are too complicated, a customized genetic algorithm is developed. Numerical experiments show that considering sensor failure makes a significant performance improvement in the sensor placement pattern. Sensitivity analysis is also applied to investigate the impact of a number of allowable sensors and different traffic sensor failure probability.