探地雷达在桥梁预应力管道定位检测中的应用

对预应力管道进行定位检测,是目前桥梁无损检测技术的一个重要问题,在阐述探地雷达无损检测技术原理和方法的基础上,通过室内模型试验,并结合工程实例说明了高精度探地雷达在桥梁预应力管道定位检测中的应用,及其无损、简易、效率高、精度高、抗干扰能力强的优点,为准确评价桥梁结构耐久性和安全使用功能提供科学依据。     

认知语境与英语学习中的主动倾听

认知语境是一种理论构架,是人头脑中固有知识的集合体.主动倾听是听者积极寻找话语含义的一种认知方法,通过分析认知语境对英语学习中主动倾听影响,对大学英语的科研改革带来一点启示.     

浅埋顶管沉井周边土体的三维破坏形状及沉降研究

为研究顶管沉井及周边土体在顶进力作用下的形变范围与大小，以加固旋喷桩作为沉井周围加固体建立ABAQUS软件计算模型，并将模拟结果与工程实例、PLAXIS 3D软件所得结果进行对比分析。同时，采用广州地区花岗岩残积土进行室内沉井模型试验，并通过试验结果对数值模拟结论进行验证，得出结论如下： 1）在开挖基坑前达到设计强度的旋喷桩能有效减小基坑周边土体塌陷变形、坑底隆起。2）在施加工作顶推力下，前侧主动区首先出现贯通裂缝，竖向位移斜率增大出现明显拐点；继续增大顶推力，土体位移会急剧增大导致地表沉降严重。3）对于后背土体，在顶推力作用下，地表破裂线的切线角度从0°逐渐增大至45°+φ/2，导致破裂范围也不断扩大；达到45°+φ/2处后，继续施加顶推力会导致短轴方向破坏范围扩大的速度较长轴方向的速度更快；三维空间中被动区破坏土体在地表处产生形状为椭圆的破坏面，椭圆长轴方向为顶推轴线方向，被动破坏体呈现为牛角状椭圆楔体。     

主动铰接盾构在连续小半径曲线中风化泥岩的掘进控制技术

武汉市轨道交通11号线东段工程光谷四路站—光谷五路站区间为"S"型连续曲线,最小平曲线半径为350 m,采用盾构法施工。通过对主动铰接盾构机掘进控制的难点分析,从土压力、千斤顶推力、千斤顶行程差、水平铰接角度和前盾水平趋向等方面采取有针对性的技术控制措施,使成型隧道轴线、管片错台控制在规范允许范围之内,成功解决了连续小半径曲线隧道盾构施工轴线难以控制、管片容易错台等大问题。     

软土地层盾尾注浆压力引起的地面隆起分析

目前已有盾尾注浆压力引起地面隆起的研究均假定盾尾注浆压力均匀分布,这与实际工程中盾尾注浆压力上小下大的形式不符。为更准确预测盾尾注浆压力引起的地面变形,在现有均匀注浆压力引起地面隆起分析的基础上,考虑软土地层盾构隧道施工中盾尾注浆压力上小下大的分布形式,将盾尾注浆对地层的压力效应视为半无限土体中柱形孔的扩张过程,利用镜像法和Mindlin解,推导出软土地层盾尾注浆压力引起的地面隆起计算公式,并通过工程实例,将本文解答、叶飞解答、林存刚经验公式解答、Vesic解答与数值解进行对比分析。结果表明:盾尾注浆压力引起的地面隆起横向曲线总体上呈高斯分布。在预测软土地层地面沉降时,忽视盾尾注浆压力引起的地面隆起是不合理的;用推导出的公式计算上小下大分布形式下盾尾注浆压力引起的地面沉降是可行的,Vesic公式和林存刚经验公式在应用时需要根据具体工程进行相应修正。     

使用聚合物对纯砂层进行渣土改良的试验研究

土压平衡盾构在不同的地层进行渣土改良的关键是选择合适的改良剂,纯砂层施工中最常用的改良剂就是膨润土泥浆,目前已开始尝试使用聚合物进行改良。本文选取3种典型的聚合物,研究聚合物溶液特性与聚合物浓度、搅拌时间和静置时间的关系,并选择合适的聚合物对粗砂试样进行塌落度试验、渗透试验和直剪试验的室内试验研究。研究结果表明,针对粗砂地层(含水率10%左右),0.3%的PAM聚合物溶液注入率为20%~25%时,能有效增强粗砂的流动性和黏聚性,降低渗透系数和摩擦因数,满足土压平衡盾构施工要求。     

圆形隧道施工对不同深度地层沉降影响的模型试验研究

为了预测圆形隧道施工引起地表以下不同埋深地层沉降特征,首先,通过理论推导不同地层最大沉降位移与沉降槽宽度系数的函数关系;然后,建立包括试验台架、地层模型、圆形隧道开挖模型以及测量地层变形装置的平面应变模型试验系统。通过理论解析和模型试验可知:1)地表以下地层的最大沉降位移与沉降槽宽度系数成反比;2)不同深度地层的沉降位移随着地层埋深的增加而增大,且地表以下地层沉降槽曲线仍然符合正态分布;3)通过对模型试验数据进行回归分析,得到黏土地表以下不同深度地层沉降槽宽度系数的计算公式,从而为预测圆形隧道施工地表以下不同深度地层竖向位移提供了一种可靠的计算方法。     

极高地应力软岩隧道超前导洞应力释放及多层支护变形控制技术

为了解决极高地应力软岩隧道大变形控制难题,以兰渝铁路木寨岭隧道岭脊核心段施工为例,通过现场试验和数据分析,得到如下主要结论:1)提出了"先放后抗,抗放结合,锚固加强"的变形控制理念;2)得出了该隧道岭脊核心段"超前导洞应力释放+圆形4层支护结构+径向注浆+长锚杆+长锚索"综合变形控制方案;3)超前导洞应力释放效果明显,正洞累计变形减小幅度约为34%;4)得到了圆形多层支护结构变形规律;5)累计变形均控制在设计预留变形量内,保证了该隧道岭脊核心段大变形控制效果。     

Magneto-rheological suspensions for improving ground vehicle’s ride comfort,stability, and handling

ABSTRACT

A state-of-the-art discussion on the applications of magneto-rheological (MR) suspensions for improving ride comfort, handling, and stability in ground vehicles is discussed for both road and rail applications. A historical perspective on the discovery and engineering development of MR fluids is presented, followed by some of the common methods for modelling their non-Newtonian behaviour. The common modes of the MR fluids are discussed, along with the application of the fluid in valve mode for ground vehicles’ dampers (or shock absorbers). The applications span across nearly all road vehicles, including automobiles, trains, semi-trucks, motorcycles, and even bicycles. For each type of vehicle, the results of some of the past studies is presented briefly, with reference to the originating study. It is discussed that Past experimental and modelling studies have indicated that MR suspensions provide clear advantages for ground vehicles that far surpasses the performance of passive suspension. For rail vehicles, the primary advantage is in terms of increasing the speed at which the onset of hunting occurs, whereas for road vehicles – mainly automobiles – the performance improvements are in terms of a better balance between vehicle ride, handling, and stability. To further elaborate on this point, a single-suspension model is used to develop an index-based approach for studying the compromise that is offered by vehicle suspensions, using the H₂ optimisation approach. Evaluating three indices based on the sprung-mass acceleration, suspension rattlespace, and tyre deflection, it is clearly demonstrated that MR suspensions significantly improve road vehicle’s ride comfort, stability, and handling in comparison with passive suspensions. For rail vehicles, the simulation results indicate that using MR suspensions with an on-off switching control can increase the speed at which the on-set of hunting occurs by as much as 50% to more than 300%.     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.