变频器输出电压du/dt对电机的影响及其滤波器的设计

研究了变频器输出电压du/dt对电机端电压和轴承电流的影响,在PSpice中建立了电机高频模型,并对端电压波形进行了仿真;着重研究了一种du/dt滤波器的参数设计方法,并且进行了仿真和实验验证。实践证明,该滤波器具有较好的滤波效果。     

CARD/1系统在互通立交设计绘图上的应用与开发

通过对CARD/1系统在T型（Y型）互通式立体交叉设计绘图上的二次开发，使T型（Y型）互通式立体交叉的设计绘图达到一体化。     

液力变矩器泵轮流场数值分析

应用计算流体动力学(CFD)方法，采用非结构网格和稳态交互面技术，模拟了液力变矩器三维内流场，并与试验相对照，验证了数值模拟的正确性。分析了泵轮进口、中弦面、出口面速度场和压力场，以及泵轮流道流场形态及流场形成的机理。     

车用催化转化器流动阻力影响因素的研究

流动阻力是车用催化转化器的重要性能之一。作者对载体结构参数，入口扩张管和出口收这三个因素进行了试验研究，并对载体通道的流动进行了理论分析，提出了一种计算载体流动阻力的方法。研究结果表明，载体结构参数和扩张管锥角对流动阻力影响显著，而收缩管锥角的影响不明显，在载体结构参数中，减小载体壁厚是降低催化器阻力的有效措施。     

车用三效催化转化器排放特性的数值模拟

将催化转化器的几种化学反应机理与控制方程结合在一起建立了转化器的数学模型，对其进行数值求解，结果与实验值吻合较好，验证了模型的正确性，为以后进一步提出更加准确的数学模型提供了一种可靠的方法，具有重要的应用价值。     

Wheel-rail contact models for vehicle system dynamics including multi-point contact

Advanced modelling of rail vehicle dynamics requires realistic solutions of contact problems for wheels and rails that are able to describe contact singularities, encountered for wheels and rails. The basic singularities demonstrate themselves as double and multiple contact patches. The solutions of the contact problems have to be known practically in each step of the numerical integration of the differential equations of the model. The existing fast, approximate methods of solution to achieve this goal have been outlined. One way to do this is to replace a multi-point contact by a set of ellipses. The other methods are based on so-called virtual penetration. They allow calculating the non-elliptical, multiple contact patches and creep forces online, during integration of the model. This allows nearly real-time simulations. The methods are valid and applicable for so-called quasi-Hertzian cases, when the contact conditions do not deviate much from the assumptions of the Hertz theory. It is believed that it is worthwhile to use them in other cases too.     

Simulation on progressive collapse behaviour of whole ship model under extreme waves using idealized structural unit method

To ensure the safety of navigating ship, working loads and structural load-carrying capacity are two important aspects. In the present paper, a total simulation system combing load calculation and structural collapse analysis is applied to simulate progressive collapse behaviour of a single-hull Kamsarmax type bulk carrier. A three dimensional singularity distribution method is adopted to calculate pressure distribution with time history. A mixed structural model, collapse part simulated by ISUM elements and remaining part by elastic FEM elements with relative coarse mesh, is proposed for collapse analysis. Progressive collapse behaviour obtained by ISUM is good agreement with that by nonlinear software package, MARC. However, the calculation time of ISUM analysis is about 1/70 of MARC analysis. The applicability to structure system, high accuracy and sufficient efficiency of ISUM had been demonstrated.     

集装箱装卸桥吊具卷缆系统防失控改造

针对西门子电控系统集装箱桥吊吊具卷缆子系统在使用过程中发现的缺陷进行改造。通过修改西门子变频器参数,可有效避免桥吊吊具卷缆系统由于通信故障引发的失控,不但节约了成本,而且提高了桥吊可靠性。     

R/S分析法在盾构下穿机场过程中的地表变形规律研究

为保证机场的正常运营,在盾构下穿机场的施工过程中,对地表沉降变形控制的要求较高,因此对穿越过程中的施工控制和变形规律研究具有重要意义。首先,基于盾构下穿机场的工程条件,分析盾构下穿过程中的风险,并提出相应的控制措施;同时,根据现场监测数据,分析盾构下穿机场过程中的地表沉降变形规律,并利用R/S分析法对地表沉降的发展趋势进行研究。结果表明:盾构施工引起的机场地表变形均在控制值范围以内,且各监测点在不同序列条件下的Hurst指数均大于0.5,具有沉降持续减弱的趋势,验证下穿过程中风险控制措施的有效性,为类似下穿机场的盾构施工提供一定的实践经验,也为盾构施工引起的地表沉降变形规律研究提供参考。     

船舶低硫柴油系统设计的分析与优化

就新辟航线首制船“汉亚直达”集装箱船的低硫柴油系统,叙述了船舶低硫柴油系统的设计经验,从当前国内外对船用燃油硫含量的要求、应对方案到船舶低硫柴油冷却方式选择、低硫柴油冷却系统设计、高/低硫柴油转换、使用低硫柴油风险分析及处理等方面进行详细叙述,为业内同行提供参考。