ZPW-2000A轨道电路小轨电压异常判断分析

ZPW-2000A轨道电路小轨电压反映调谐区的状态。一是日常出现的波动原因较多,造成现场不容易查找;二是发生故障时,对小轨电压关注分析不够,造成查找故障走弯路。结合现场经验及案例,利用信号集中监测数据及曲线,分析小轨电压波动、异常成因。     

基于高频方波注入的船舶电机无传感器控制研究

随着大功率交流调速技术的不断进步,船舶电力推进如今成为船舶行业的主要发展目标.为研究运行可靠稳定、灵活、高性能的船舶电机无位置传感器控制,系统采用高频注入法估算电机转子位置信号,根据基于高频注入永磁同步电机数学模型的研究,该系统中高频采用的是高频方波注入,减少滤波器的使用从而缓解了转子位置延迟现象,同时采用锁相环对电机转子的相位和频率跟踪来计算电机转子的估计转速,克服了估算转速脉动大的困难.利用Matlab对电机控制系统仿真,验证电机控制系统的电机转速平滑稳定,转子位置波形在0-2π有规律往返.最终实现高精度、灵活的无传感器船舶电机控制.     

A real-time adaptive signal control in a connected vehicle environment

The state of the practice traffic signal control strategies mainly rely on infrastructure based vehicle detector data as the input for the control logic. The infrastructure based detectors are generally point detectors which cannot directly provide measurement of vehicle location and speed. With the advances in wireless communication technology, vehicles are able to communicate with each other and with the infrastructure in the emerging connected vehicle system. Data collected from connected vehicles provides a much more complete picture of the traffic states near an intersection and can be utilized for signal control. This paper presents a real-time adaptive signal phase allocation algorithm using connected vehicle data. The proposed algorithm optimizes the phase sequence and duration by solving a two-level optimization problem. Two objective functions are considered: minimization of total vehicle delay and minimization of queue length. Due to the low penetration rate of the connected vehicles, an algorithm that estimates the states of unequipped vehicle based on connected vehicle data is developed to construct a complete arrival table for the phase allocation algorithm. A real-world intersection is modeled in VISSIM to validate the algorithms. Results with a variety of connected vehicle market penetration rates and demand levels are compared to well-tuned fully actuated control. In general, the proposed control algorithm outperforms actuated control by reducing total delay by as much as 16.33% in a high penetration rate case and similar delay in a low penetration rate case. Different objective functions result in different behaviors of signal timing. The minimization of total vehicle delay usually generates lower total vehicle delay, while minimization of queue length serves all phases in a more balanced way.     

有轨电车交叉口交通组织及控制方案优化

有轨电车在运行过程中,易在交叉口处产生瓶颈,导致有轨电车通行速度降低、乘客舒适度下降。从有轨电车交叉口信号优先控制、现状交叉口交通管理与控制优化、公共交通组织优化、慢行交通组织优化4个方面提出了相应的优化措施。以武汉市有轨电车作为实例,提出了一系列改善措施,并利用VISSIM软件仿真模拟了实施效果,仿真结果验证了优化方案的科学性和有效性。     

信号倒计时影响下的进口道交通流分析与建模

为揭示信号倒计时对驾驶决策行为的影响,本文基于实测数据对信号控制进口道各断面的车速分布特征进行了分析,研究发现临近停车线处于不同断面位置的车辆行驶特性由于信号倒计时的有无及剩余绿灯时间的影响而存在差异.提出了考虑信号倒计时下驾驶心理的元胞自动机模型,通过数值模拟剖析了不同时空条件(位置、车速与剩余时间)下微观驾驶心理与行为对中观交通流的作用机理.结果表明,该模型可较好地刻画信号灯控制下城市进口道路车辆运行特性.     

基于主线拥堵场景的快速路级联信号控制方法

城市快速路高峰时段已经呈现出常态性拥堵，对快速路主线拥堵进行疏导尤为必要.本文通过在主线和入口匝道进行三级交通检测判别，设计了多级联动的信号控制流程与实现方式，构建了不同拥堵程度下的分级响应控制策略，基于瓶颈点通行能力最大化下的实时信号控制算法及最大排队长度限制下的实时信号控制算法，建立了主线及匝道车道开关闭、汇合处信号灯控制、主线动态限速、交通信息诱导等于一体的快速路级联信号控制方法.仿真分析结果表明，在主线不同拥堵程度下采取的级联信号控制方法，可以有效提升快速路主线平均车速，并未导致匝道排队的恶化，局部路网平均延误均有明显降低.     

基于移动导航数据的信号配时反推

在交通管理和评价时,信号配时对监测评价路口运行状态,评价路口配时方案至关重要.但是,大范围的实时信号配时方案的获取尚缺乏简明有效的途径.本文提出两种基于移动导航数据计算固定配时路口信号配时的方法.第一种方法是在不考虑驾驶员驾驶行为差异性时,得到路口红灯和车均延误的关系模型,从而计算某相位的红灯时长.另外一种方法是基于车辆通过停止线的时间,结合本文提出的上升梯度法,得到某阶段红灯时长.本文通过实际的路口案例计算,将预测结果和已知路口的信号配时比较,表明此方法计算得到的红绿灯时长准确度较高,为后续进行路口运行状态和通行能力研究提供了数据支持.     

Understanding the impacts of a combination of service improvement strategies on bus running time and passenger’s perception

Transit agencies implement many strategies in order to provide an attractive transportation service. This article aims to evaluate the impacts of implementing a combination of strategies, designed to improve the bus transit service, on running time and passenger satisfaction. These strategies include using smart card fare collection, introducing limited-stop bus service, implementing reserved bus lanes, using articulated buses, and implementing transit signal priority (TSP). This study uses stop-level data collected from the Société de transport de Montréal (STM)’s automatic vehicle location (AVL) and automatic passenger count (APC) systems, in Montréal, Canada. The combination of these strategies has lead to a 10.5% decline in running time along the limited stop service compared to the regular service. The regular route running time has increased by 1% on average compared to the initial time period. The study also shows that riders are generally satisfied with the service improvements. They tend to overestimate the savings associated with the implementation of this combination of strategies by 3.5-6.0 min and by 2.5-4.1 min for both the regular route and the limited stop service, respectively. This study helps transit planners and policy makers to better understand the effects of implementing a combination of strategies to improve running time and passenger’s perception of these changes in service.     

汕头苏埃隧道方案设计关键技术研究

根据汕头苏埃隧道的建设条件,对工程方案设计中的几个技术难点进行研究,并提出解决方案。通过采用"多级分流"理念,实现隧道与北岸4条城市主干道的交通衔接;选择"抛石+排水板"方案解决海域深厚淤泥地层中的围堰设计;8度高烈度震区选择合理的抗震减震措施解决隧道结构抗震;采取双道密封垫和加大密封垫断面的防水设计,满足地震时管片接缝张开量大的防水要求;针对复杂地层,对盾构选型和配置提出建议;对海底凸起进入隧道内的硬岩进行爆破预处理,以降低盾构施工风险。     

A signal-based fault detection and classification method for heavy haul wagons

This paper proposes a signal-based fault detection and isolation (FDI) system for heavy haul wagons considering the special requirements of low cost and robustness. The sensor network of the proposed system consists of just two accelerometers mounted on the front left and rear right of the carbody. Seven fault indicators (FIs) are proposed based on the cross-correlation analyses of the sensor-collected acceleration signals. Bolster spring fault conditions are focused on in this paper, including two different levels (small faults and moderate faults) and two locations (faults in the left and right bolster springs of the first bogie). A fully detailed dynamic model of a typical 40t axle load heavy haul wagon is developed to evaluate the deterioration of dynamic behaviour under proposed fault conditions and demonstrate the detectability of the proposed FDI method. Even though the fault conditions considered in this paper did not deteriorate the wagon dynamic behaviour dramatically, the proposed FIs show great sensitivity to the bolster spring faults. The most effective and efficient FIs are chosen for fault detection and classification. Analysis results indicate that it is possible to detect changes in bolster stiffness of ±25% and identify the fault location.