Estimation of value of travel time reliability

In mode choice decision, travelers consider not only travel time but also reliability of its modes. In this paper, reliability was expressed in terms of standard deviation and maximum delay that were measured based on triangular distribution. In order to estimate value of time and value of reliability, the Multinomial and Nested Logit models were used. The analysis results revealed that reliability is an important factor affecting mode choice decisions. Elasticity is used to estimate the impacts of the different policies and system improvements for water transportation mode. Among these policies, decision maker can assess and select the best alternative by doing the benefit and cost analysis based on a new market share, the value of time, and the value of reliability. Finally, a set of promising policies and system improvement of the water transportation were proposed.     

Optimum design of tilting bogie frame in consideration of fatigue strength and weight

This paper addresses the use of finite-element (FE) analysis to calculate the fatigue strength of a bogie frame, for the development of tilting trains in Korea. A multi-body dynamic analysis was performed to extract the load condition by tilting on curves. Using the results of the multi-body dynamic analysis and the load scenario setout in the UIC standard, FE analysis was performed to obtain the stress distribution and to calculate the fatigue strength. An attempt was made to minimize the weight of the bogie frame using a back-propagation artificial neural network (ANN). The results of this study reveal that the stresses at some nodes are near the fatigue limit in the Goodman diagram and by using back-propagation ANN, the weight of the bogie frame could be reduced by 4.7%.     

Development of hot stamped center pillar using form die with channel type indirect blank holder

The hot stamping process has been used in the automotive industry to reduce the weight of the body-in-white and to increase passenger safety via improved crashworthiness. However, defects such as fracture and wrinkle occur when hot stamping is performed using a conventional drawing or forming method. In this study, a channel-type indirect blank holder (CIBH) is proposed to develop a high-strength center pillar in form-type hot stamping, so that the aforementioned drawbacks are overcome. This type of blank holder plays an important role in reducing severe wrinkling at the flange; such wrinkling leads to folding after the completion of form-type hot-stamping. First, we investigated the effect of the channel shape on the indirect blank holding force by using a simplified two-dimensional plane-strain stamping process. Second, we selected the slope angle and corner radius of the channel as the main shape parameters by finite element analysis and artificial neural network (ANN). It is known that fracture at the hot formed wall and wrinkle at the flange are significantly affected by the slope angle of the channel, and the appropriate value for eliminating fracture and wrinkle is determined to be 99°. By performing hot stamping using a form die with the selected channel, we can manufacture a high-strength center pillar without wrinkle and fracture.     

Performance comparison between pedestrian push-button and pre-timed pedestrian crossings at midblock: a Korean case study

Walking has been highlighted as an independent transportation mode as well as an access/egress mode to/from public transit to encourage the use of more sustainable transport systems. However, walking does not seem to have priority over other transportation modes, especially in areas where various modes of movement are in conflict. The pedestrian push-button system seems to be a solution to distribute the right of way. The focus of this study is on the performance issue of the pedestrian push-button. Specifically, this study deals with issues related to mid-block crossings and attempts to answer two questions: whose waiting time is longer at pre-timed and push-button crossings, pedestrians, or vehicles? and which system – pre-timed or push-button – is better in terms of total waiting time? According to our simulation analyses, if the pedestrian flow rate is less than 120, 85, and 70 ped/h for two-, three-, and four-lane roads, respectively, the push-button system is recommended.     

Disturbance Observer-Based Sideslip Angle Control for Improving Cornering Characteristics of In-Wheel Motor Electric Vehicles

In this paper, a robust sideslip angle controller based on the direct yaw moment control (DYC) is proposed for in-wheel motor electric vehicles. Many studies have demonstrated that the DYC is one of the effective methods to improve vehicle maneuverability and stability. Previous approaches to achieve the DYC used differential braking and active steering system. Not only that, the conventional control systems were commonly dependent on the feedback of the yaw rate. In contrast to the traditional control schemes, however, this paper proposes a novel approach based on sideslip angle feedback without controlling the yaw rate. This is mainly because if the vehicle sideslip angle is controlled properly, the intended sideslip angle helps the vehicle to pass through the corner even at high speed. On the other hand, the vehicle may become unstable because of the too large sideslip caused by unexpected yaw disturbances and model uncertainties of time-varying parameters. From this aspect, disturbance observer (DOB) is employed to assure robust performance of the controller. The proposed controller was realized in CarSim model described actual electric vehicle and verified through computer simulations.     

Crosswind Feedforward Control - A Measure to Improve Vehicle Crosswind Behaviour

The theory of crosswind feedforward control was explained using the example of a vehicle with active front-wheel steering. Beforehand, the calculation formulas and frequency responses of the transient crosswind force and of the wind yaw moment acting on the vehicle were derived using the example of a simple vehicle fluid model. The influence of the transiency of crosswind disturbance on the dynamic crosswind behaviour of a vehicle was then presented. The results of simulation confirmed the analyses carried out in the frequency domain for feedforward control with front, rear and all-wheel steering. With front-wheel steering, the influence of crosswind on one of the vehicle movement variables (lateral acceleration or yaw rate) could be almost completely compensated by dynamic feedforward control. With rear-wheel steering, it is only possible to compensate directly for the influence on the yawing rate. Due to the setting of the side force in the same direction as the lateral wind force at the start, active rear-wheel steering is not so successful as active front-wheel steering. Nevertheless, the crosswind behaviour of a vehicle can be considerably enhanced by feedforward control with rear-wheel steering. The best crosswind behaviour was obtained with active all-wheel steering: the vehicle hardly responds at all to crosswinds and remains on course despite heavy gusts of wind.     

Urban travel demand: The impact of Box-Cox transformations with nonspherical residual errors

We develop an algorithm for solving regression models with Box-Cox transformations on both the dependent and independent variables, while simultaneously taking into account corrections for serial correlation of several orders and for heteroscedasticity. The latter correction is of a general form which contains as special cases most specifications of heteroscedasticity found in practice. We apply the procedure to three urban travel demand functions, two of which are currently used in their linear form by the Montreal Transit Authority, and analyze more than 100 specifications. Our results show that taking into account nonsphericalness of the residuals has a major impact on model parameter estimates, notably on those which determine the functional form of the model, and that, conversely, modifications of the functional form have strong implications for both the structure of autocorrelation and the importance of heteroscedasticity; moreover, we find interactions between autocorrelation and heteroscedasticity structures. We introduce a special measure of elasticity for variables which contain zero observations, particularly dummy variables. Moreover, we find that elasticities of demand and implicit values of time depend to a large extent on the stochastic specification of the model.     

Durability prediction for automobile aluminum front subframe using nonlinear models in virtual test simulations

This research work presents fatigue life evaluation techniques for an automotive vehicle aluminum front subframe using virtual test simulation technology with nonlinear suspension components model. The technology was used for improving the accuracy of the polynomial model used in conventional analysis. The proposed nonlinear suspension components models were developed using direct approach. The effects of the nonlinear elements on the prediction of the fatigue life were also analyzed. Actual aluminum front subframe was tested using half-car road test simulator to verify the accuracy of the models. It was found that the proposed nonlinear models yield more accurate results than conventional polynomial models. The proposed virtual test simulation technology with nonlinear suspension components model can be used to predict fatigue life for vehicle chassis structures more accurately.     

Ship-berth link performance evaluation: simulation and analytical approaches

In this paper we consider the performance evaluation of ship-berth link in port. The efficiency of operations and processes on the ship-berth link has been analysed through the basic operating parameters such as berth utilization, average number of ships in waiting line, average time that a ship spends in waiting line, average service time of a ship, average total time that a ship spends in port, average quay crane (QC) productivity and average number of QCs per ship. All the main performances of the ship-berth link are given. This is one of the problems faced by planners and terminal operators in ports. In this paper, we propose two models based on simulation and queuing theory, respectively, in order to determine the performance evaluation of ship-berth link in port. Numerical results and computational experiments are reported to evaluate the efficiency of the models for Pusan East Container Terminal (PECT).     

Mean Value WGT Diesel Engine Calibration Model for Effective Simulation Research

Recently, to improve vehicle fuel economy, as well as the performance of internal combustion engines, optimized system matching between a vehicle’s drivetrain and engine has become a very important technical issue. For this reason, the need for simulation research on engine and vehicle performance improvement has increased. But in general, since both engine simulation and vehicle simulation require initial engine calibration map input, a simple engine calibration method is required for the efficient configuration of various virtual engine calibration map setups. On this background, in this study, an example of waste gate turbocharger (WGT) cooled — exhaust gas recirculation (EGR) Diesel engine calibration using a test-based mean value engine model is presented as a suitable engine calibration map setting method. Also, the feasibility of an engine calibration model is confirmed through various engine tests. Using the simple model presented here, it is possible for diverse engine operating conditions and engine performance maps to be acquired.