Strong bottom–up effects on phytoplankton community caused by a rainfall during spring and summer in Sagami Bay,Japan

To assess the consequences of bottom-up effects on phytoplankton community composition during the rainy season, phytoplankton levels and environmental factors were monitored daily from 12 April to 22 July 2003 in Sagami Bay, Japan. The relevant environmental factors were analyzed using cross-correlation analyses. Based on time-series analysis, low surface salinity conditions lasting 0 or 2 days after heavy rainfalls resulted in significant nutrient loading, such as dissolved inorganic nitrogen (DIN), into the coastal area. Also, Chlorophyll-a (Chl-a) concentration frequently increased 2 and 6 days after rainfall. Based on the high total Chl-a concentration, the time was divided into three periods, from 1 to 11 May (Period A), 26 May to 9 June (Period B) and 30 June to 22 July (Period C). The phytoplankton assemblages during Period A were dominated by two dinoflagellates, Ceratium furca and Ceratium fusus. Prior to these species blooming, the heterotrophic dinoflagellate Noctiluca scintillans was dominant. During Period B, the phytoplankton communities were dominated primarily by the diatoms Rhizosolenia delicatula, Hemiaulus sinensis and Navicula spp. Finally, Cerataulina dentata, Rhizosolenia spp., Lauderia borealis and Neodelphineis pelagica were dominant during Period C. After increases in phytoplankton abundance, available nitrogen (N) and phosphorous (P) were consumed and exhausted, which were considered a potential cause of the shift in the dominant organisms from large diatoms to pico- and nano-plankton in the low Chl-a environment. In particular, silicate (Si) was not a major limiting factor for phytoplankton production, since the Si:DIN and Si:P ratios clearly demonstrated that there were no any potential stoichiometric Si limitations, and almost all silicate concentrations were > 2.0 µM during this study. Our results reveal that nutrient sources supplied by river discharge are a main cue for strong bottom–up effects on algal bloom succession during the early summer season in Sagami Bay.     

Performance comparison between pedestrian push-button and pre-timed pedestrian crossings at midblock: a Korean case study

Walking has been highlighted as an independent transportation mode as well as an access/egress mode to/from public transit to encourage the use of more sustainable transport systems. However, walking does not seem to have priority over other transportation modes, especially in areas where various modes of movement are in conflict. The pedestrian push-button system seems to be a solution to distribute the right of way. The focus of this study is on the performance issue of the pedestrian push-button. Specifically, this study deals with issues related to mid-block crossings and attempts to answer two questions: whose waiting time is longer at pre-timed and push-button crossings, pedestrians, or vehicles? and which system – pre-timed or push-button – is better in terms of total waiting time? According to our simulation analyses, if the pedestrian flow rate is less than 120, 85, and 70 ped/h for two-, three-, and four-lane roads, respectively, the push-button system is recommended.     

Performance Design of an Exhaust Superheater for Waste Heat Recovery of Construction Equipment

Although fuel cost has been the largest portion of annual operating costs of construction equipment, it is possible to save the energy and reduce cost using fuel economy enhancement technology. In this study, an organic Rankine cycle is applied to an excavator in order to recover waste heat, reproduce it into electrical energy, and consequently reduce the fuel consumption by 10 %. A design process was carried out to develop an exhaust gas superheater that recovers the waste heat from exhaust gas through a composite-dimensional thermal flow analysis. A one-dimensional code was developed to perform a size design for the exhaust gas superheater. The ranges for the major design parameters were determined to satisfy the target of the heat recovery, as well as the pressure drop at both fluid sides. Performance analysis was done through onedimensional design code results, which were compared with three-dimensional CFD analysis. By utilizing a 3D commercial code, the arrangement of the tubes was selected and the working fluid pressure drop was reduced through a detailed layout design. The design procedure was verified by a performance evaluation of the prototype, which yielded only a 7 % tolerance in heat recovery.     

Design and implementation of a new clamping force estimator in Electro-Mechanical Brake systems

In this paper, an improved clamping force estimator is proposed for Electro-Mechanical Brake (EMB) systems by using the motor rotor position information and the hysteresis characteristics of mechanical parts in the EMB. A cascaded type of a force/position control system with a force sensor or an estimator was designed and implemented to control the clamping force and to keep the clearance gap in EMB systems. The EMB Hardware-In-the-Loop-Simulation (HILS) results show that the proposed force estimator yields better estimation performance than the existing estimator and that the clamping force control system based on the estimator can be also used for the fault tolerant control of the system.     

Approach to functional safety-compliant ECU design for electro-mechanical brake systems

In this paper, we propose a design approach to a functional safety-compliant ECU for an electro-mechanical brake (EMB) control system or an electronic wedge brake (EWB) control system. Brake actuators in a brake-by-wire (BBW) system such as EMB or EWB are characterized by the safety-critical functions which are now executed by using many electric and electronic devices with application software. Based on hazard analysis and risk assessments of the automotive functional safety standard ISO 26262, the proposed EMB control system should be ASIL-D-compliant, which is the highest ASIL level. To this end, a hardware and a software design method is introduced to implement functionl safety-oriented monitoring functions which are based on an asymmetric dual-core architecture with an external watchdog processor. It is shown by using EMB hardware-In-the-Loop-Simulation (HILS) that the proposed ECU design approach is very effective when a hardware fault or software execution faults occur in the EMB ECU, moreover, this functional safety-compliant design can be well combiled with the sensor fault-tolerant control logic.     

Vehicle velocity estimation using effective inertia for an in-wheel electric vehicle

In this study, a vehicle velocity estimation algorithm for an in-wheel electric vehicle is proposed. This algorithm estimates the vehicle velocity using the concept of effective inertia, which is based on the motor torque, the angular velocity of each wheel and vehicle acceleration. Effective inertia is a virtual mass that changes according to the state of a vehicle, such as acceleration, deceleration, turning or driving on a low friction road. The performance of the proposed vehicle velocity estimation algorithm was verified in various conditions that included straight driving, circle driving and low friction road driving using the in-wheel electric vehicle that was equipped with an in-wheel system in each of its rear wheels.     

An adaptive information fusion model to predict the short-term link travel time distribution in dynamic traffic networks

As intelligent transportation systems (ITS) approach the realm of widespread deployment, there is an increasing need to robustly capture the variability of link travel time in real-time to generate reliable predictions of real-time traffic conditions. This study proposes an adaptive information fusion model to predict the short-term link travel time distribution by iteratively combining past information on link travel time on the current day with the real-time link travel time information available at discrete time points. The past link travel time information is represented as a discrete distribution. The real-time link travel time is represented as a range, and is characterized using information quality in terms of information accuracy and time delay. A nonlinear programming formulation is used to specify the adaptive information fusion model to update the short-term link travel time distribution by focusing on information quality. The model adapts good information by weighing it higher while shielding the effects of bad information by reducing its weight. Numerical experiments suggest that the proposed model adequately represents the short-term link travel time distribution in terms of accuracy and robustness, while ensuring consistency with ambient traffic flow conditions. Further, they illustrate that the mean of a representative short-term travel time distribution is not necessarily a good tracking indicator of the actual (ground truth) time-dependent travel time on that link. Parametric sensitivity analysis illustrates that information accuracy significantly influences the model, and dominates the effects of time delay and the consistency constraint parameter. The proposed information fusion model bridges key methodological gaps in the ITS deployment context related to information fusion and the need for short-term travel time distributions.     

Toxic air pollutants and trucking productivity in the US

This paper introduces toxic air pollutants into the measurement of trucking productivity to obtain true productivity growth. Our results show that omitting or ignoring toxic air pollutants in measuring trucking productivity yields statistically significant biased productivity estimates in for 2002-2005. Trucking productivity growth was understated by the traditional productivity measure, because the latter did not account for reductions in truck air pollution over time. We also find that the difference between traditional and environmental efficiency scores was negligible, suggesting that environmental constraint did not distort efficiency in the trucking sector.     

Sharing piping CAD models of ocean plants based on international standards

In the shipbuilding industry, different computer-aided design (CAD) systems are used for different design domains, structure, and outfitting. We need to exchange data among different CAD systems such as Tribon, AutoCAD, Intergraph or PDMS to complete the whole design and production process. There are two approaches to data exchange. One is direct translation; the other is indirect translation, which is based on a neutral format. If we use a neutral format, the data specification is open to the public and the design model can be used by other CAD systems, including next-generation CAD systems. In this paper, we propose an indirect method that uses ISO 10303 (STandard for the Exchange of Product model data) AP227 and ISO 15926 to define neutral formats. A separate ShapeDB is constructed to manage the geometry information, referenced to the catalogue data defined by ISO 15926. An experimental implementation for data exchange between Tribon and PDMS is described.     

Development of a rigid-ended beam element for analysis of bracketed frame structures

At the initial design stage, for rapid evaluation of strength of ship structures, finite element analysis using beam elements is carried out as a rule. In beam modeling of ship structures, brackets are usually represented by rigid elements to simplify the analysis. The extent of rigid ends, which is called the span point, can be determined from the three kinds of view points, i.e., bending, shearing and axial deformation.

In this paper, a novel beam element is developed. The developed novel beam element, referred to as the rigid-ended beam element, can consider the effect of three kinds of span point within one element, which was impossible in modeling with the ordinary beam element. Calculated results agree with the exact solution for a cantilever beam and also with results obtained from finite element analysis using membrane elements. Structural analysis using the rigid-ended beam element is revealed to have good computing efficiency due to the elements not needing to correspond to the brackets.