Costs of air pollutants from shipping: a meta-regression analysis

ABSTRACT

This study estimated the external cost of air pollution from shipping by means of a meta-regression analysis, which has not been made before. Three pollutants, which were included in most of the primary studies, were considered: nitrogen oxides (NO_x), sulphur dioxides (SO₂) and particulate matters with a diameter of max 2.5 micrometres (PM_2.5). All primary studies included damages of health and a majority added impacts on agriculture and estimated the cost of air pollutants by transferring cost estimates from studies on costs of air emissions from transports in Europe. Different regression models and estimators were used and robust results were found of statistically significant emission elasticities of below one, i.e. total external costs increase by less than 1% when emissions increase by 1%. There was a small variation between the pollutants, with the highest elasticity for PM_2.5 and lowest for NO_x. Calculations of the marginal external cost of the pollutants showed the same pattern, with this cost being approximately six times higher for PM_2.5 than for the other pollutants. Common to all pollutants was that the marginal external cost decreases when emission increases. Another robust result was a significant increase in the cost of studies published in journals compared with other publication outlets. These findings point out some caution when transferring constant external unit cost of air pollutant from shipping, which is much applied in the literature, and the cost functions estimated in this study could thus provide a complementary transfer mechanism.     

Transit assignment under crowded conditions

This paper presents a transit assignment algorithm for crowded networks. Both congestion in vehicles and queuing at stations are explicitly taken into account in predicting passenger flows for a fixed pattern of origin-destination trip demands. The overflow effects due to insufficient capacity of transit lines are considered to be concentrated at transit stations, while the in-vehicle congestion effects (or discomforts) are considered to be dependent on in-vehicle passenger volume. Overflow delay at a transit station is dependent on the number of excess passengers required to wait for the next transit car. We use a logit model to determine the split between passengers that chose to wait for the next transit car and passengers that chose to board on the alternative transit lines. The proposed algorithm predicts how passenger will choose their optimal routes under both queuing and crowded conditions.     

A study of passenger discomfort measures at the Hong Kong mass transit railway system

This note investigates the important attributes relating to the crowding effects at the Mass Transit Railway (MTR) stations in Hong Kong. Data was collected at two sets of three MTR stations to study the responses of the passengers due to the discomfort at crowded vehicles and platforms. Stated preference surveys were used to study the effects of passenger discomfort measures.     

The role of professional associations in shipping

This article is in three parts. The first covers the historical development of qualifying associations. The second covers the particular role of maritime institutions that include The Royal Institution of Naval Architects, The Institute of Marine Engineering Science and Technology and The Nautical Institute. The third and final section considers the future for maritime professional associations in the context of international shipping.     

Estimation of origin‐destination matrices for a multimodal public transit network

This paper presents a procedure for the estimation of origin‐destination (O‐D) matrices for a multimodal public transit network. The system consists of a number of favored public transit modes that are obtained from a modal split process in a traditional four‐step transportation model. The demand of each favored mode is assigned to the multimodal network, which is comprised of a set of connected links of different public transit modes. An entropy maximization procedure is proposed to simultaneously estimate the O‐D demand matrices of all favored modes, which are consistent with target data sets such as the boarding counts and line segment flows that are observed directly in the network. A case study of the Hong Kong multimodal transit network is used to demonstrate the effectiveness of the proposed methodology.     

A traffic flow simulator for short‐term travel time forecasting

This paper presents an off‐line forecasting system for short‐term travel time forecasting. These forecasts are based on the historical traffic count data provided by detectors installed on Annual Traffic Census (ATC) stations in Hong Kong. A traffic flow simulator (TFS) is developed for short‐term travel time forecasting (in terms of offline forecasting), in which the variation of perceived travel time error and the fluctuations of origin‐destination (O‐D) demand are considered explicitly. On the basis of prior O‐D demand and partial updated detector data, the TFS can estimate the link travel times and flows for the whole network together with their variances and covariances. The short‐term travel time forecasting by O‐D pair can also be assessed and the O‐D matrix can be updated simultaneously. The application of the proposed off‐line forecasting system is illustrated by a numerical example in Hong Kong.     

Analysis of Driver's Decelerating Strategy in a Car-following Situation

This report describes a decelerating driver-model expressed by driving mode transition in car-following situations. The assumptions for constructing the model are that decelerating strategy of a driver is classified into several simple driving modes and that a driver changs his driving modes based on his perceptible characteristics and experiential rules. Deceleration action is divided into three states; following, standing and braking, which are applied to the model. The model has two paths for driver's decelerating action, one of which is selected by the driver based on the perceptible characteristics and experiential rules. The suitability of the model has been experimentally verified.     

Driver requirements and road traffic informatics

Initially the driver's role as a link in the driver-vehicle-road-traffic control-chain is discussed in a historical perspective. The gradual changes and the advantages and problems arising from these changes are discussed from behavioural point of view.Then the driver tasks are analyzed. A separation is made between trip planning, navigation, road following, traffic interaction, rule compliance, other than traffic tasks, car handling and speed choice. The relations between and the weights of these subtasks are discussed. Some existing driver behaviour models are reviewed in relation to the above mentioned tasks.Finally an effort is made based on the analyses of driver tasks and driver models to specify some general and some more specific potential advantages and problems with expected future RTI-systems.     

The design of bus route systems — An interactive location-allocation approach

An interactive modelling approach is developed to solve the practical problem of bus route network design. Possible bus routes are identified with facilities which can be located. Zones or pairs of zones in the urban area are identified with customers who will be allocated to the established facilities. It is shown that the classical Set Covering Problem is useful under the assumption of fixed demand; the Simple Plant Location Problem is effective under the assumption of demand which is sensitive to the level of bus service provided.     

A simple formulation for predicting the ultimate strength of ships

The aim of this study is to derive a simple analytical formula for predicting the ultimate collapse strength of a single- and double-hull ship under a vertical bending moment, and also to characterize the accuracy and applicability for earlier approximate formulations. It is known that a ship hull will reach the overall collapse state if both collapse of the compression flange and yielding of the tension flange occur. Side shells in the vicinity of the compression and the tension flanges will often fail also, but the material around the final neutral axis will remain in the elastic state. Based on this observation, a credible distribution of longitudinal stresses around the hull section at the overall collapse state is assumed, and an explicit analytical equation for calculating the hull ultimate strength is obtained. A comparison between the derived formula and existing expressions is made for largescale box girder models, a one-third-scale frigate hull model, and full-scale ship hulls.List of symbols A _B total sectional area of outer bottom - A _B total sectional area of inner bottom - A _D total sectional area of deck - A _S half-sectional area of all sides (including longitudinal bulkheads and inner sides) - a _s sectional area of a longitudinal stiffener with effective plating - b breadth of plate between longitudinal stiffeners - D hull depth - D _B height of double bottom - E Young's modulus - g neutral axis position above the base line in the sagging condition or below the deck in the hogging condition - H depth of hull section in linear elastic state - I _s moment of inertia of a longitudinal stiffener with effective plating - l length of a longitudinal stiffener between transverse beams - M _E elastic bending moment - M _p fully plastic bending moment of hull section - M _u ultimate bending moment capacity of hull section - M _uh ,M _us ultimate bending moment in hogging or sagging conditions - r radius of gyration of a longitudinal stiffener with effective plating [=(I _s /a _s )^1/2] - t plate thickness - Z elastic section modulus at the compression flange - Z _B ,Z _D elastic section modulus at bottom or deck - slenderness ratio of plate between stiffeners [= (b/t)(_y/E)^1/2] - slenderness ratio of a longitudinal stiffener with effective plating [=(l/r)(_y/E)^1/2] - _y yield strength of the material - _yB , _yB , _yD yield strength of outer bottom, inner bottom - _yS deck, or side - _u ultimate buckling strength of the compression flange - _uB , _uB , _uD ultimate buckling strength of outer bottom - _uS inner bottom, deck, or side