A Novel Iterative Receiver Based on Extrinsic Information Update for MIMO Systems

A novel iterative receiver for multiple input multiple output (MIMO) systems was introduced. Its basis concept is that the reliability of extrinsic information will be strengthened with continuous iterations. Extrinsic information of present iteration is added with prior information of last iteration to obtain performance gain. The simulation results show that the improved iterative receiver can approach the 5th iteration performance of conventional soft interference cancellation (SIC)-minimum mean square error (MMSE) iterative receiver after the 2nd iteration with less computational complexity. Compared with conventional iterative receiver, the improved iterative receiver has 1dB performance gain at bit error rate (BER) of 10~ -5 , with four transmit antennas and four receive antennas system.     

PIC-MF-based Iterative Receiver for Multiuser Space Frequency Block Coding Systems

A novel low-complexity iterative receiver for multiuser space frequency block coding (SFBC) system was proposed in this paper. Unlike the conventional linear minimum mean square error (MMSE) detector, which requires matrix inversion at each iteration, the soft-in soft-out (SISO) detector is simply a parallel interference cancellation (PIC)-matched filter (MF) operation. The probability density function (PDF) of PIC-MF detector output is approximated as Gaussian, whose variance is calculated with a priori information fed back from the channel decoder. With this approximation, the log likelihood ratios (LLRs) of transmitted bits are under-estimated. Then the LLRs are multiplied by a constant factor to achieve a performance gain. The constant factor is optimized according to extrinsic information transfer (EXIT) chart of the SISO detector. Simulation results show that the proposed iterative receiver can significantly improve the system performance and converge to the matched filter bound (MFB) with low computational complexity at high signal-to-noise ratios (SNRs).     

基于Gram-Schmidt正交化法的串行干扰消除算法

基于Gram-Schmidt正交化法,提出了一种改进的串行干扰消除算法.不同于传统的串行干扰消除算法,该算法运用Gram-Schmidt正交化法,通过扩频序列获取正交序列作为最优解扩码,使得检测器每一级最强用户的解扩码与其他用户的扩频码所张的子空间正交,从而实现对多址干扰的完全抑制.给出了具有幅度失配的系统误码率近似公式,讨论了幅度失配对检测性能的影响.仿真结果表明,改进算法能有效抑制CDMA系统中的多址干扰,改善系统性能.     

Lattice reduction aided MMSE Tomlinson-Harashima precoding based on VBLAST algorithm for MIMO systems

A lattice reduction aided （LRA） minimum mean square error （MMSE） Tomlinson-Harashima precoding （THP） was proposed based on vertical Bell Labs layered space time （VBLAST） algorithm for multiple input multiple output （MIMO） systems. The extended channel was used to provide optimal tradeoff between residual interference and noise amplification. The processing based on lattice reduction method helps achieve maximal diversity order. The VBLAST algorithm was applied to get the optimal processing ordering for successive interference cancellation （SIC） at transmitter. Simulation results show that the proposed algorithm outperforms conventional THP and the LRA zero-forcing （ZF） THP with full diversity order.     

Lattice-basis reduction precoding based on successive interference cancellation design for multiuser MIMO downlink system

Two kinds of lattice-basis reduction precoding schemes based on successive interference cancellation are proposed. The successive interference cancellation (SIC) structure can be obtained by either orthogonal and a right triangular matrix (QR) decomposition, or the Vertical Bell Labs Layered Space Time (VBLAST) algorithm which provides optimal user ordering. Moreover, the extended channel approach is applied to the proposed SICbased schemes. Simulation results show that the proposed schemes can achieve comparable BER performance to vector precoding (VP).     

An Iterative Power Allocation Algorithm for Group-wise Space-Time Block Coding Systems

An iterative transmit power allocation (PA) algorithm was proposed for group-wise space-time block coding (G-STBC) systems with group-wise successive interference cancellation (GSIC) receivers. Group-wise interference suppression (GIS) filters are employed to separate each group's transmit signals from other interferences and noise. While the total power on all transmit symbols is constrained, all transmit PA coefficients are updated jointly according to the channel information at each iteration. Through PA, each detection symbol has the same post-detection signal to interference-and-noise ratio (SINR). The simulation results verify that the proposed PA algorithm converges at the equilibrium quickly after few iterations, and it achieves much lower bit error rates than the previous single symbol SIC PA and the fixed ratio PA algorithms for G-STBC systems with GSIC receivers .     

New applications of EXIT chart for iterative decoding systems

Applications on iterative control and multiple input multiple output （MIMO） system were developed. Two new charts derived from extrinsic information transfer （EXIT） chart were employed as the designing tools, which are called as output mutual information chart with defined iterative degree （DID） chart and near optimum output mutual information （NOMI） chart respectively. Different from the EXIT chart, they can show the iterative performance on the whole signal-to-noise ratio range with one single curve, whereas computation complexity is greatly reduced compared with conventional bit error ratio （BER） performance curve. The iterative control was implemented according to a near-optimum iterative degree vector determined by NOMI chart, the reasonability of uncertain parameters was analyzed in one MIMO system. The concepts were illustrated based on bit-interleaved coded modulation with iterative decoding （BICM-ID）.     

Improved List Sphere Decoder for Multiple Antenna Systems

An improved list sphere decoder （ILSD） is proposed based on the conventional list sphere decoder （LSD） and the reduced- complexity maximum likelihood sphere-decoding algorithm. Unlike the conventional LSD with fixed initial radius, the ILSD adopts an adaptive radius to accelerate the list cdnstruction. Characterized by low-complexity and radius-insensitivity, the proposed algorithm makes iterative joint detection and decoding more realizable in multiple-antenna systems. Simulation results show that computational savings of ILSD over LSD are more apparent with more transmit antennas or larger constellations, and with no performance degradation. Because the complexity of the ILSD algorithm almost keeps invariant with the increasing of initial radius, the BER performance can be improved by selecting a sufficiently large radius.     

同时确定内燃机活塞温度场与边界换热系数的自适应迭代法

本文根据实测温度数据确定内燃机活塞温度场同时决定边界换热系数,建议了自适应迭代方法。文中详细分析了换热系数的自适应迭代规律,据此编制了自适应迭代程序,其中温度场的数值算法可根据计算装备的实际拥有情况具体选用有限元或者边界元。自适应迭代法不依赖于任何经验公式,计算工作量小,且计算时间比传统的经验试凑法大为减少。      

Improved Space-Time Selective Interference Cancellation Scheme for CDMA Systems

IntroductionAdaptiveantennaarrayscanreduceco channelinterference (CCI)fromotherusersaswellasmitigatetheeffectofmultipathfadinginwirelessenvironments .SinceCDMAsystemsareinterferencelimitedinnature ,smartantennahasbeenregardedasoneofthecoresystemcomponents…     

基于零中频技术的 GSM 接收机的研究和开发

针对传统的GSM接收机一般采用二次变频超外差方案或一次变频的低中频方案，提出了一种基于零中频的实现方案，它采用一片AD公司的高性能下变频芯片ADRF6801，配以简单的前级放大和滤波电路，电路简洁，可以实现较好的性能指标，满足产品小型化、低功耗的要求。实际测试表明，采用该方案实现的接收机噪声系数低，灵敏度高，可应用于GSM接收的各种场合。     

Robust digital audio watermarking scheme using blind source separation with global optimal property

The paper proposes a robust digital audio watermarking scheme using blind source separation(BSS) based on the global optimization of independency metric(IM),which is formulated as a generalized eigenvalue(GE) problem.Compared with traditional information-theoretical approaches used in digital audio watermarking,such as fast independent component analysis(FastICA),the proposed scheme has lower complexity without timeconsuming iteration steps used in FastICA.To make full use of the multiresolution characteris...     

基于可控量子隐形传态的代理签名方案

提出了一种量子代理签名方案．基于可控量子隐形传态，采用3粒子纠缠态作为量子信道，不同于经典的基于计算复杂性的代理签名方案，本方案利用量子隐形传态的物理特性来实现签名及验证，具有无条件安全性．     

基于GP2010的GPS接收机前端模块实现

为了研制自主知识产权的GPS接收机,首先要设计合理的GPS接收机前端模块．结合GPS接收机的工作原理,提出了切实可行GPS接收机的前端电路实现方案,给出了相应的实验数据,并对其中的关键模块及器件选取进行了详细的介绍．结果表明,该前端电路硬件平台是稳定可靠的．     

STC-OFDM系统的post-IDFT多波束形成技术

提出了适用于空时编码-正交频分复用(OFDM)系统的后-逆离散傅立叶变换(post-IDFT)多波束形成技术.该技术通过对空频信道相关矩阵进行特征分解获得多个特征模式,再利用空时分组码(STBC)各发射分支信号的正交性使OFDM系统形成多个post-IDFT波束.接收端根据STBC传输矩阵的正交性对多波束解码.系统获得的空间分集增益为空频信道相关矩阵的特征值之和,最大空间分集增益与子载波波束形成方案相同,误码率比STC-OFDM的低.该技术将复杂度降低到子载波波束形成方案的1/S(S为OFDM系统的子载波数目),而且当波束维数(m)小于发射天线数目(M)时,可进一步减少M-m个IDFT模块     

A new algorithm for non-newtonian flow and its application in mould filling process

The simulation of injection molding process requires a stable algorithm to model the molten polymer with non-isothermal non-Newtonian property. In this paper, a staggered and iterative scheme is particularly designed to solve the velocity-pressure-temperature variables. In consideration of the polymer characteristic of high viscosity and low thermal conductivity, the non-Newtonian momentum-mass conservation equations are solved by the Crank-Nicolson method based split (CNBS) scheme, and the energy conservation equation with convective character is discretized by the characteristic Galerkin (CG) method. In addition, an arbitrary Lagrangian Eulerian (ALE) free surface tracking and mesh generation method is introduced to catch the front of the fluid flow. The efficiency of the proposed scheme is demonstrated by numerical experiments including a lid-driven cavity flow problem and an injection molding problem.     

MIMO双向中继网络的预编码设计与功控策略

为加强MIMO双向中继系统的空间复用增益,研究一种低复杂度的发送和接收预编码矩阵.利用子空间对齐方法,将双向MIMO信道分解为多路单入单出（SISO）的子信道形式,使得两个源用户能够使用网络编码获取更好的空间复用增益.同时通过矩阵计算和转化,给出了一种优化的功率分配方案.在确定优化矩阵后,该方案能够为每个子信道独立地进行优化功率分配,并且能够得到各节点间优化功率分配的闭合表达式,从而将算法复杂度从O（n3）降低为O（n）.仿真结果表明,在典型场景下,所提方案在具有更低复杂度的优势下,系统性能接近优化的梯度下降迭代方案,优于传统单纯前向放大转发方式（AF） ,有2.99 bit/（sHz）的性能增益.      

基于光正交码的不规则LDPC码

基于光正交码构造了一类新的不规则OOC LDPC码.新的LDPC码是准循环码,其编码复杂度与码长成线性关系,具有编码复杂度低的特点,它所对应的双向图中没有四线循环.用和积译码算法对新的码字进行了仿真,结果表明,与具有类似参数的随机码和规则OOC LDPC码相比,当信道误码率为10-5时,译码增益分别为0.3和0.15dB.     

Solving airlines disruption by considering aircraft and crew recovery simultaneously

When disruptions occur, the airlines have to recover from the disrupted schedule. The recovery usually consists of aircraft recovery, crew recovery and passengers’ recovery. This paper focuses on the integrated recovery, which means above-mentioned two or more recoveries are considered as a whole. Taking the minimization of the total cost of assignment, cancellation and delay as an objective, we present a more practical model, in which the maintenance and the union regulations are considered. Then we present a so-called iterative tree growing with node combination method. By aggregating nodes, the possibility of routings is greatly simplified, and the computation time is greatly decreased. By adjusting the consolidating range, the computation time can be controlled in a reasonable time. Finally, we use data from a main Chinese airline to test the algorithm. The experimental results show that this method could be used in the integrated recovery problem.     

机车车辆车体结构动应力计算方法

为了提高机车车辆的疲劳寿命,优化其结构设计,提出了基于多系统仿真模型和有限元方法的动应力混合计算方法,计算了机车车辆车体结构的动应力。建立以车体为核心的机车多体系统仿真模型,并进行动力学分析,获得关键位置的载荷时间历程。通过有限元准静态应力法,计算了车体结构的准静态应力影响因子。通过载荷时间历程和对应单位载荷作用下的应力影响因子的相互相乘叠加求和计算,获得车体结构在随机动载作用下的应力历程,对实际线路车体结构动应力测试结果和刚性车体与柔性车体的仿真结果进行了对比。对比结果表明:其误差分别是2.462%和7.258%,说明此计算方法计算精度高。