An analytical approximation for the macroscopic fundamental diagram of urban traffic

This paper shows that a macroscopic fundamental diagram (MFD) relating average flow and average density must exist on any street with blocks of diverse widths and lengths, but no turns, even if all or some of the intersections are controlled by arbitrarily timed traffic signals. The timing patterns are assumed to be fixed in time. Exact analytical expressions in terms of a shortest path recipe are given, both, for the street’s capacity and its MFD. Approximate formulas that require little data are also given.For networks, the paper derives an upper bound for average flow conditional on average density, and then suggests conditions under which the bound should be tight; i.e., under which the bound is an approximate MFD. The MFD’s produced with this method for the central business districts of San Francisco (California) and Yokohama (Japan) are compared with those obtained experimentally in earlier publications.     

Automatic calibration of fundamental diagram for first‐order macroscopic freeway traffic models

Despite its importance in macroscopic traffic flow modeling, comprehensive method for the calibration of fundamental diagram is very limited. Conventional empirical methods adopt a steady state analysis of the aggregate traffic data collected from measurement devices installed on a particular site without considering the traffic dynamics, which renders the simulation may not be adaptive to the variability of data. Nonetheless, determining the fundamental diagram for each detection site is often infeasible. To remedy these, this study presents an automatic calibration method to estimate the parameters of a fundamental diagram through a dynamic approach. Simulated flow from the cell transmission model is compared against the measured flow wherein an optimization merit is conducted to minimize the discrepancy between model‐generated data and real data. The empirical results prove that the proposed automatic calibration algorithm can significantly improve the accuracy of traffic state estimation by adapting to the variability of traffic data when compared with several existing methods under both recurrent and abnormal traffic conditions. Results also highlight the robustness of the proposed algorithm. The automatic calibration algorithm provides a powerful tool for model calibration when freeways are equipped with sparse detectors, new traffic surveillance systems lack of comprehensive traffic data, or the case that lots of detectors lose their effectiveness for aging systems. Furthermore, the proposed method is useful for off‐line model calibration under abnormal traffic conditions, for example, incident scenarios. Copyright © 2015 John Wiley & Sons, Ltd.     

A multi-commodity Lighthill–Whitham–Richards model of lane-changing traffic flow

Systematic lane changes can seriously deteriorate traffic safety and efficiency inside lane-drop, merge, and other bottleneck areas. In our previous studies (Jin, 2010a, Jin, 2010b), a phenomenological model of lane-changing traffic flow was proposed, calibrated, and analyzed based on a new concept of lane-changing intensity. In this study, we further consider weaving and non-weaving vehicles as two commodities and develop a multi-commodity, behavioral Lighthill–Whitham–Richards (LWR) model of lane-changing traffic flow. Based on a macroscopic model of lane-changing behaviors, we derive a fundamental diagram with parameters determined by car-following and lane-changing characteristics as well as road geometry and traffic composition. We further calibrate and validate fundamental diagrams corresponding to a triangular car-following fundamental diagram with NGSIM data. We introduce an entropy condition for the multi-commodity LWR model and solve the Riemann problem inside a homogeneous lane-changing area. From the Riemann solutions, we derive a flux function in terms of traffic demand and supply. Then we apply the model to study lane-changing traffic dynamics inside a lane-drop area and show that the smoothing effect of HOV lanes is consistent with observations in existing studies. The new theory of lane-changing traffic flow can be readily incorporated into Cell Transmission Model, and this study could lead to better strategies for mitigating bottleneck effects of lane-changing traffic flow.     

Traffic flow on pedestrianized streets

Giving pedestrians priority to cross a street enhances pedestrian life, especially if crosswalks are closely spaced. Explored here is the effect of this management decision on car traffic. Since queuing theory suggests that for a given pedestrian flux the closer the crosswalk spacing the lower the effect of pedestrians on cars, scenarios where pedestrians can cross anywhere should be best for both cars and pedestrians. This is the kind of pedestrianization studied.Analytic formulas are proposed for a pedestrianized street’s capacity, free-flow speed and macroscopic fundamental diagram. Of these, only the free-flow speed formula is exact. The analytic form of the capacity formula is inspired by analytic upper and lower bounds derived with variational theory for a version of the problem where cars are treated as a fluid. The formula is then calibrated against microscopic simulations with discrete cars. The MFD for the fluid version of the problem is shown to be concave and have a certain symmetry. These two geometrical properties, together with the formulae for capacity and free-flow speed, yield a simple approximation for the MFD.Both the capacity and MFD formulae match simulations with discrete cars well for all values of the pedestrian flux – errors for the capacity are well under 0.2% of the capacity before pedestrianization. Qualitatively, the formulas predict that the street’s capacity is inversely proportional to the square root of the pedestrian flux for low pedestrian fluxes, and that pedestrians increase the cars’ free-flow pace by an amount that is proportional to the pedestrian flux.     

Analysis of asymmetric driving behavior using a self-learning approach

This paper presents a self-learning Support Vector Regression (SVR) approach to investigate the asymmetric characteristic in car-following and its impacts on traffic flow evolution. At the microscopic level, we find that the intensity difference between acceleration and deceleration will lead to a ‘neutral line’, which separates the speed-space diagram into acceleration and deceleration dominant areas. This property is then used to discuss the characteristics and magnitudes of microscopic hysteresis in stop-and-go traffic. At the macroscopic level, according to the distribution of neutral lines for heterogeneous drivers, different congestion propagation patterns are reproduced and found to be consistent with Newell’s car following theory. The connection between the asymmetric driving behavior and macroscopic hysteresis in the flow-density diagram is also analyzed and their magnitudes are shown to be positively related.     

Traffic state estimation and uncertainty quantification based on heterogeneous data sources: A three detector approach

This study focuses on how to use multiple data sources, including loop detector counts, AVI Bluetooth travel time readings and GPS location samples, to estimate macroscopic traffic states on a homogeneous freeway segment. With a generalized least square estimation framework, this research constructs a number of linear equations that map the traffic measurements as functions of cumulative vehicle counts on both ends of a traffic segment. We extend Newell’s method to solve a stochastic three-detector problem, where the mean and variance estimates of cell-based density and flow can be analytically derived through a multinomial probit model and an innovative use of Clark’s approximation method. An information measure is further introduced to quantify the value of heterogeneous traffic measurements for improving traffic state estimation on a freeway segment.     

Measuring the completeness of complete streets

A tool for measuring the “completeness” of a complete street has applications in developing policy, prioritising areas for infrastructure investment for a network, and solving the right-of-way allocation problem for individual streets. A literature review was conducted on the state-of-art in the assessment complete street designs. Complete streets assessment requires a context-sensitive approach, thus context-sensitive standards of “completeness” must first be established by combining a street classification system with sets of priorities and target performance levels for the different types of streets. Performance standards should address a street’s fulfilment of the movement, environmental, and place functions, and be flexible enough to account for the many ways that these functions of a street can be fulfilled. Most frameworks reviewed are unsuitable for evaluating complete streets because, with few exceptions, they guide street design by specifying the design elements for inclusion on the street. Secondly, the performance of a street can be assessed according to transportation, environmental, and place criteria, and compared to the target performance levels specified by the street’s classification. As there are many different impacts to consider on a street, additional work is required to define the priorities and performance objectives for different types of streets.     

On the allocation of city space to multiple transport modes

Abstract

This paper analyzes urban multimodal transportation systems in an aggregated way. To describe the aggregate behavior of traffic in cities, use is made of an idea that is now receiving some attention: the macroscopic fundamental diagram (MFD). We demonstrate through simulation how the MFD can be used to monitor and control a real network, in this case a portion of San Francisco, using readily available input data. We then show how different modes interact on the same network and discuss how these interactions might be incorporated into an MFD for multimodal networks. The work unveils two main results: first, it confirms recent results showing that restricting access to a city's congested areas can improve mobility for all travelers, including those who endure the restrictions; and second, that dedicating street space to collective transport modes can improve accessibility for all modes, even those from which space is taken away.     

A probabilistic stationary speed–density relation based on Newell’s simplified car-following model

Probabilistic models describing macroscopic traffic flow have proven useful both in practice and in theory. In theoretical investigations of wide-scatter in flow–density data, the statistical features of flow density relations have played a central role. In real-time estimation and traffic forecasting applications, probabilistic extensions of macroscopic relations are widely used. However, how to obtain such relations, in a manner that results in physically reasonable behavior has not been addressed. This paper presents the derivation of probabilistic macroscopic traffic flow relations from Newell’s simplified car-following model. The probabilistic nature of the model allows for investigating the impact of driver heterogeneity on macroscopic relations of traffic flow. The physical features of the model are verified analytically and shown to produce behavior which is consistent with well-established traffic flow principles. An empirical investigation is carried out using trajectory data from the New Generation SIMulation (NGSIM) program and the model’s ability to reproduce real-world traffic data is validated.     

The Aw–Rascle and Zhang’s model: Vacuum problems,existence and regularity of the solutions of the Riemann problem

In this paper we will discuss some aspects of the recent macroscopic models of the second-order proposed by [Aw, A., Rascle, M., 2000. Resurrection of second order models of traffic flow. SIAM Journal of Applied Mathematics 60 (3), 916–938] and [Zhang, H.M., 2002. A non-equilibrium traffic model devoid of gas-like behavior. Transportation Research Part B 36, 275–290]. These models were suggested after the publication of an article written by [Daganzo, C.F., 1995. Requiem for second-order fluid approximations of traffic flow. Transportation Research Part B 29, 277–286] showing that some classical second-order models can exhibit non-physical solutions. It is shown in this note that the ARZ (Aw–Rascle–Zhang) model respects the anisotropic character of traffic flow, that it yields physical solutions, and that vacuum problems can be solved satisfactorily, provided that the fundamental diagram (equilibrium speed–density relationship) is extended in a suitable fashion. It follows that the Riemann problem for the ARZ model with extended fundamental diagram always admits a solution, and that this solution depends continuously on the initial conditions.     

The identification and empirical characterization of vehicular (Lagrangian) fundamental diagrams in multilane traffic flow

Traditional macroscopic traffic flow modeling framework adopts the spatial–temporal coordinate system to analyze traffic flow dynamics. With such modeling and analysis paradigm, complications arise for traffic flow data collected from mobile sensors such as probe vehicles equipped with mobile phones, Bluetooth, and Global Positioning System devices. The vehicle‐based measurement technologies call for new modeling thoughts that address the unique features of moving measurements and explore their full potential. In this paper, we look into the concept of vehicular fundamental diagram (VFD) and discuss its engineering implications. VFD corresponds to a conventional fundamental diagram (FD) in the kinematic wave (KW) theory that adopts space–time coordinates. Similar to the regular FD in the KW theory, VFD encapsulates all traffic flow dynamics. In this paper, to demonstrate the full potential of VFD in interpreting multilane traffic flow dynamics, we generalize the classical Edie's formula and propose a direct approach of reconstructing VFD from traffic measurements in the vehicular coordinates. A smoothing algorithm is proposed to effectively reduce the nonphysical fluctuation of traffic states calculated from multilane vehicle trajectories. As an example, we apply the proposed methodology to explore the next‐generation simulation datasets and identify the existence and forms of shock waves in different coordinate systems. Our findings provide empirical justifications and further insight for the Lagrangian traffic flow theory and models when applied in practice. Copyright © 2015 John Wiley & Sons, Ltd.     

A rolling-horizon quadratic-programming approach to the signal control problem in large-scale congested urban road networks

The paper investigates the efficiency of a recently developed signal control methodology, which offers a computationally feasible technique for real-time network-wide signal control in large-scale urban traffic networks and is applicable also under congested traffic conditions. In this methodology, the traffic flow process is modeled by use of the store-and-forward modeling paradigm, and the problem of network-wide signal control (including all constraints) is formulated as a quadratic-programming problem that aims at minimizing and balancing the link queues so as to minimize the risk of queue spillback. For the application of the proposed methodology in real time, the corresponding optimization algorithm is embedded in a rolling-horizon (model-predictive) control scheme. The control strategy’s efficiency and real-time feasibility is demonstrated and compared with the Linear-Quadratic approach taken by the signal control strategy TUC (Traffic-responsive Urban Control) as well as with optimized fixed-control settings via their simulation-based application to the road network of the city centre of Chania, Greece, under a number of different demand scenarios. The comparative evaluation is based on various criteria and tools including the recently proposed fundamental diagram for urban network traffic.     

Probe vehicle-based traffic state estimation method with spacing information and conservation law

This paper proposes a method of estimating a traffic state based on probe vehicle data that contain spacing and position of probe vehicles. The probe vehicles were assumed to observe spacing by utilizing an advanced driver assistance system, that has been implemented in practice and is expected to spread in the near future. The proposed method relies on the conservation law of the traffic flow but is independent of a fundamental diagram. The conservation law is utilized for reasonable aggregation of the spacing data to acquire the traffic state, i.e., a flow, density and speed. Its independence from a fundamental diagram means that the proposed method does not require predetermined nor exogenous assumptions with regard to the traffic flow model parameters. The proposed method was validated through a simulation experiment under ideal conditions and a field experiment conducted under actual traffic conditions; and empirical characteristics of the proposed method were investigated.     

Real-time energy-efficient traffic control via convex optimization

This article proposes a macroscopic traffic control strategy to reduce fuel consumption of vehicles on highways. By implementing Greenshields fundamental diagram, the solution to Moskowitz equations is expressed as linear functions with respect to vehicle inflow and outflow, which leads to generation of a linear traffic flow model. In addition, we build a quadratic cost function in terms of vehicle volume to estimate fuel consumption rate based on COPERT model. A convex quadratic optimization problem is then formulated to generate energy-efficient traffic control decisions in real-time. Simulation results demonstrate significant reduction of fuel consumption on testing highway sections under peak traffic demands of busy hours.     

Traffic guidance–perimeter control coupled method for the congestion in a macro network

Macroscopic fundamental diagram (MFD) describes the macro relationship between a network vehicle density and a network space mean flow, without requiring the mastery of complex origin to destination data. Thus, MFD provides an opportunity for the macro control of urban road network. However, most of the existing MFD control methods ignore the active role of traffic guidance in solving congestion problems. This study presents a traffic guidance–perimeter control coupled (TGPCC) method to improve the performance of macroscopic traffic networks. The method considers the optimal cumulative volume of a network as the goal and establishes a programming function according to the network equilibrium rule of traffic flow amongst multiple MFD sub-regions, which regards the minimum delay of network, as the objective. The Logit model for the compliance rate of driver route guidance is established by the stated preference survey. Moreover, the perimeter control (PC) method is proposed for adjusting the phase split of intersections. Finally, three schemes, namely, the TGPCC, PC and the method without PC and guidance are tested on a network with four well-defined MFD sub-regions. Results show that the TGPCC addresses the issue of congestion and decreases the total delay accordingly.     

Pedestrian streets in Singapore

A fair amount of literature pertaining to pedestrian streets has been produced but for the most part it is on the American and European developments. There has been surprisingly little published research on pedestrian street development in Asia. The purpose of this paper, therefore, is to examine pedestrian streets in Asia, using the city-state of Singapore as a case study. Since the mid-1980s, pedestrian streets have been adopted as a policy in the conservation and planning of Singapore's city centre. The resulting pedestrian streets came in many forms, from a single pedestrian-only street to a whole precinct of several streets.     

Continuous formulations and analytical properties of the link transmission model

The link transmission model (LTM) has great potential for simulating traffic flow in large-scale networks since it is much more efficient and accurate than the Cell Transmission Model (CTM). However, there lack general continuous formulations of LTM, and there has been no systematic study on its analytical properties such as stationary states and stability of network traffic flow. In this study we attempt to fill the gaps. First we apply the Hopf–Lax formula to derive Newell’s simplified kinematic wave model with given boundary cumulative flows and the triangular fundamental diagram. We then apply the Hopf–Lax formula to define link demand and supply functions, as well as link queue and vacancy functions, and present two continuous formulations of LTM, by incorporating boundary demands and supplies as well as invariant macroscopic junction models. With continuous LTM, we define and solve the stationary states in a road network. We also apply LTM to directly derive a Poincaré map to analyze the stability of stationary states in a diverge-merge network. Finally we present an example to show that LTM is not well-defined with non-invariant junction models. We can see that Newell’s model and continuous LTM complement each other and provide an alternative formulation of the network kinematic wave theory. This study paves the way for further extensions, analyses, and applications of LTM in the future.     

Three-phase traffic theory and two-phase models with a fundamental diagram in the light of empirical stylized facts

Despite the availability of large empirical data sets and the long history of traffic modeling, the theory of traffic congestion on freeways is still highly controversial. In this contribution, we compare Kerner’s three-phase traffic theory with the phase diagram approach for traffic models with a fundamental diagram. We discuss the inconsistent use of the term “traffic phase” and show that patterns demanded by three-phase traffic theory can be reproduced with simple two-phase models, if the model parameters are suitably specified and factors characteristic for real traffic flows are considered, such as effects of noise or heterogeneity or the actual freeway design (e.g. combinations of off- and on-ramps). Conversely, we demonstrate that models created to reproduce three-phase traffic theory create similar spatiotemporal traffic states and associated phase diagrams, no matter whether the parameters imply a fundamental diagram in equilibrium or non-unique flow-density relationships. In conclusion, there are different ways of reproducing the empirical stylized facts of spatiotemporal congestion patterns summarized in this contribution, and it appears possible to overcome the controversy by a more precise definition of the scientific terms and a more careful comparison of models and data, considering effects of the measurement process and the right level of detail in the traffic model used.     

Recent developments in traffic flow modeling using macroscopic fundamental diagram

ABSTRACT

This paper presents an overview of the recent developments in traffic flow modelling and analysis using macroscopic fundamental diagram (MFD) as well as their applications. In recent literature, various aggregated traffic models have been proposed and studied to analyse traffic flow while enhancing network efficiency. Many of these studies have focused on models based on MFD that describes the relationship between aggregated flow and aggregated density of transport networks. The analysis of MFD has been carried out based on experimental data collected from sensors and GPS, as well as simulation models. Several factors are found to influence the existence and shape of MFD, including traffic demand, network and signal settings, and route choices. As MFD can well express the traffic dynamics of large urban transport networks, it has been extensively applied to traffic studies, including the development of network-wide control strategies, network partitioning, performance evaluation, and road pricing. This work also presents future extensions and research directions for MFD-based traffic modelling and applications.