共查询到15条相似文献,搜索用时 237 毫秒
1.
螺旋桨非定常性能的面元法预报 总被引:2,自引:1,他引:1
采用扰动速度势面元法预报螺旋桨非定常性能,桨叶、桨毂和尾涡面由双曲四边形面元进行离散,对时域内非定常问题的求解采用时间步进迭代方法,建立了桨叶随边非定常等压库塔条件的非线性迭代结构,使迭代求解更加有效、快速和稳定.预报结果与测试结果或其它数值结果比较是令人满意的. 相似文献
2.
3.
本文建立了非定常螺旋桨势函数面元法的理论方法和数值方法,发展了相应的计算机程序,采用通过迭代实现的非线性压力库塔条件,计算了一常规桨和一大侧斜桨的桨叶表面非定压力,并与测试结果及人的计算结果进行了比较。 相似文献
4.
全方向推进器非定常水动力性能的面元预报方法 总被引:3,自引:0,他引:3
研究了全方向推进器非定常水动力性能的面元预报方法,基于螺旋桨面元法建立了全方向推进器的非定常水动力性能计算的数学模型,对全方向推进器的非定常水动力性能进行了数值预报。采用了关于扰动速度势的基本积分微分方程,并采用双曲面元以消除面元间的缝隙。用Newton-Raphson迭代过程在桨叶随边满足压力Kutta条件。在计算面元的影响系数时,应用Morino导出的解析计算公式加快了数值计算的速度。为避免数值求导中的奇异性,用Yanagizawa方法求得物体表面上的速度分布。本文计算结果与日本水池模型试验结果、升力线方法计算结果及升力面方法计算结果进行了对比。 相似文献
5.
应用升力面理论涡格法和面元法,建立了拖式吊舱推进器非定常水动力性能的数值计算方法。螺旋桨桨叶采用升力面理论涡格法计算,吊舱舱体及支架采用HESS-SMITH面元法计算,螺旋桨与吊舱及支架之间的相互影响通过迭代计算来处理。针对拖式吊舱推进器,通过系统的计算和分析,研究了螺旋桨负荷、吊舱和支架诱导速度各分量以及标称与实效诱导速度对其水动力性能的影响。研究表明,就吊舱及支架的实效诱导速度而言,轴向及周向诱导速度主要由支架引起,径向诱导速度主要由吊舱舱体引起。当考察吊舱推进器的定常水动力性能时,可略去吊舱诱导速度的径向及周向分量;考察非定常性能时,可略去径向分量,但应考虑周向分量的影响。以吊舱及支架的标称诱导速度作为进流,将导致非定常推力、扭矩的平均值降低,脉动量幅值减小,因此,虽然标称诱导速度容易得到,但据此进行吊舱推进器的性能预报或设计都会引起一定的误差。非定常水动力的脉动幅值取决于船尾伴流与吊舱诱导速度的相对比例,略去吊舱诱导速度会导致桨叶非定常力的变化特征发生较大变化。 相似文献
6.
按运用二维不发片方法,计算优化一般性桨叶螺距循环变化,能消除桨叶上随时间的变化的力。运用升力面理论,对采用循环桨叶螺距的桨和相同尺寸的定距桨性能进行了比较计算,证明了舶循环螺距控制的有生。桨叶采取在每次默许中循环螺距控制,能减少桨叶上的非定常力和船体表面的压力脉动。同时,与定距桨比较而言也减少了面空泡的范围。 相似文献
7.
8.
带定子导管螺旋桨定常和非定常性能预估的基于速度势的面元法 总被引:1,自引:0,他引:1
开发了一个带定子导管螺旋桨定常和非定常水动力性能预报的数值计算方法,该方法采用基于速度势的面元法分别处理绕对带桨毂螺旋桨、导管和定子周围的流动,并通过迭代计算处理它们之间的相互干扰影响.为简化计算,采用了诱导速度的周向平均值来考虑螺旋桨、导管和定子之间定常水动力相互干扰影响.它们之间的非定常水动力相互干扰通过时间域内迭代方法求解,然而螺旋桨泄出涡、导管泄出涡和定子泄出涡之间的非定常干扰采用了时域内简化处理,这样的简化处理既保证了计算精度,又大幅度地减少了计算时间.对于螺旋桨、导管和定子的计算程序分别依次逐个运行直至每个部分的水动力收敛.算例考核表明该数值方法的计算结果与试验数据吻合较好. 相似文献
9.
螺旋桨水动力性能的数值预报方法 总被引:1,自引:0,他引:1
基于速度势的低阶面元法预报螺旋桨的水动力性能。选用四边形双曲面元对桨叶进行离散以消除面元间的缝隙,基本积分方程由格林公式导出。在面元上布置等强度源汇和偶极子。采用线性尾涡并在每个尾涡面元上布置等强度的偶极子。利用Newton-Raphson迭代过程满足桨叶随边非线性等压kutta条件,使桨叶上下表面的压力在随边处一致。利用Morino计算影响函数的解析公式,采用Yanagizawa方法求得物体表面上的速度分布,并对普通桨和大侧斜桨进行了数值预报。 相似文献
10.
11.
HUANG Sheng WANG Pei-sheng HU Jian 《船舶与海洋工程学报》2007,6(2):6-11
The hydrodynamic performance of a propeller in unsteady inflow was calculated using the surface panel method. The surfaces of blades and hub were discreted by a number of hyperboloidal quadrilateral panels with constant source and doublet distribution. Each panel's corner coordinates were calculated by spline interpolation between the main parameter and the blade geometry of the propeller. The integral equation was derived using the Green Formula. The influence coefficient of the matrix was calculated by the Morino analytic formula. The tangential velocity distribution was calculated with the Yanagizawa method, and the pressure coefficient was calculated using the Bonuli equation. The pressure Kutta condition was satisfied at the trailing edge of the propeller blade using the Newton-Raphson iterative procedure, so as to make the pressure coefficients of the suction and pressure faces of the blade equal at the trailing edge. Calculated results for the propeller in steady inflow were taken as initialization values for the unsteady inflow calculation process. Calculations were carried out from the moment the propeller achieved steady rotation. At each time interval, a linear algebraic equation combined with Kutta condition was established on a key blade and solved numerically. Comparison between calculated results and experimental results indicates that this method is correct and effective. 相似文献
12.
CHANG Xin ZOU Jing-xiang HUANG Sheng GUO Chun-yu 《船舶与海洋工程学报》2007,6(4):32-36
To design a more effective blade pitch adjustment mechanism,research was done on changes to the hydrodynamic characteristics of VVPs(Variable Vector Propeller) caused by different rules for changing pitch angle. A mathematical method for predicting the hydrodynamic characteristics of a VVP under unsteady conditions is presented based on the panel method. Mathematical models for evaluation based on potential flow theory and the Green theorem are also presented. The hydrodynamic characteristics are numerically predicted. To avoid gaps between panels,hyperboloidal quadrilateral panels were used. The pressure Kutta condition on the trailing edge of the VVP blade was satisfied by the Newton-Raphson iterative procedure. The influence coefficients of the panels were calculated by Morino's analytical formulations to improve numerical calculation speed,and the method developed by Yanagizawa was used to eliminate the point singularity on derivation calculus while determining the velocities on propeller surfaces. The calculation results show that it's best for the hydrodynamic characteristics of the VVP that pitch angle changes follow the sine rule. 相似文献
13.
螺旋桨非定常性能预估的面元法 总被引:1,自引:1,他引:0
本文建立了一个预估螺旋桨非定常性能的基于速度势的非定常面元法,该方法中采用了双曲面元,避免了面元之间的缝隙,并采用迭代方法实现非线性的等压库塔条件。文中以第22届国际水池会议(ITTC)推进技术委员会推荐的HSP桨与D4679桨和挪威船舶技术研究所(MARINTEK)提供的PF-W-B桨为算例进行了考核计算,与试验结果和其他研究工作者的计算结果比较表明,螺旋桨的非定常性能预报的结果是令人满意的。 相似文献
14.
SU Yu-min HUANG ShengCollege of Shipbuilding Engineering Harbin Engineering University Harbin China 《船舶与海洋工程学报》2002,1(1):9-15
The potential based low order surface panel method is used to predict the hydrodynamic performance of marine propellers. In present method the hyperboloidal quadrilateral panels are employed to avoid the gap between the panels. The influencecoefficients of panels are calculated by Morino's analytical formulations for increasing numerically calculating speed.The pres-sure Kutta condition is satisfied on the trailing edge of propeller blade by Newton-Raphson iterative procedure.Therefore the 相似文献
15.
导管调距桨的定常性能预估 总被引:7,自引:6,他引:1
本文建立了一个预估导管可调螺距螺旋桨水动力性能的数值计算方法,即螺旋浆用升力面理论、导管采用面元法,通过迭代计算考虑浆和导管的相互影响。引入了一个修正的螺旋浆尾涡模型,来模拟尾涡片的扭曲变形及分离现象,对导管桨性能预估的各种影响因素分析了系统研究,并考虑了桨毂对性能的影响。对JD简易导管桨和导管调距桨(JD7704导管+JDC三叶可调螺距螺旋浆)分别进行了计算,并与实验结果进行了比较。结果表明,本文所建立的方法可较好地预估导管桨的水性能,精度比以往有较大的提高。 相似文献