共查询到20条相似文献,搜索用时 250 毫秒
1.
襄阳市东西轴线项目沉管预制采用节段整体式全断面顺浇法,具有高强度、大断面、大体积的特点,管节控裂难度较大。为验证混凝土配合比、施工工艺以及裂缝控制措施的可行性及可靠性,采用Midas FEA软件,进行沉管管节在设计工况下的水化热温度应力数值仿真模拟计算,分析管节浇筑过程中混凝土内部温度及应力变化情况。数值仿真结果表明,管节连接处抗裂安全系数较低。进而选取理论开裂风险最高的边墙倒角位置和施工难度最高的中隔墙倒角位置进行模型试验,实际模拟钢筋及预埋件施工工序,全面检验原材料、配合比和混凝土施工性能的可靠性,并布设智能温度监测系统。通过局部块体试验,合理优化钢筋及预埋件的结构形式和安装工序,验证混凝土性能并优选施工配合比;同时,通过提出的原材料温控标准对模型试验进行温度智能监测数据分析。 相似文献
2.
继电器是车辆电器控制的重要控制元器件,其工作环境是瞬间大电流通过周期性闭合的触点,由于接触触点间接触电阻在闭合瞬间大电流的作用下产生焦耳热,导致触点极易发生熔焊的可能,严重影响继电器的使用性能,危害行车安全,据统计触点部分的故障率占到继电器故障率的90%以上。揭示汽车继电器触点瞬态接触传热特性,对改善继电器触点触点熔焊故障具有重要的现实意。本文采用分型接触理论建立接触电阻模型,综合考虑触点间接触力、接触面积及材料的比热容、导热系数等,建立了继电器触点闭合瞬间大电流作用下的有限元模型,模拟计算触点间的瞬态热场分布,为改善继电器触头熔焊现象提供理论支撑。 相似文献
3.
4.
为了在发动机开发初期了解发动机各结构的温度分布情况,文章采用有限元的方法对某发动机进行温度场分析。先运用Fire软件计算近壁面的温度场及流场,然后将温度以及换热系数映射到结构网格的单元上,再利用ABAQUS进行结构的温度场分析。通过对结果的分析发现,气缸盖的鼻梁区部分温度较高,但所有部件的温度均未超过材料的极限值,整个发动机的温度场分布较合理。 相似文献
5.
6.
7.
G. Y. Cho J. W. Choi J. H. Park S. W. Cha 《International Journal of Automotive Technology》2014,15(5):795-803
A transient numerical model of a lithium ion battery (LiB) pack with air cooled thermal management system is developed and validated for electric vehicle applications. In the battery model, the open circuit voltage and the internal resistance map based on experiments are used. The Butler-Volmer equation is directly considered for activation voltage loss estimation. The heat generation of cells and the heat transfer from cells are also calculated to estimate temperature distribution. Validations are conducted by comparison between experimental results at the cell level and the pack level. After validations, the effects of module arrangement in a battery pack are studied with different ambient temperature conditions. The configuration that more LiB cells are placed near the air flow inlet is more effective to reduce the temperature deviation between modules. 相似文献
8.
通过模拟某轻客车的前舱熔断丝盒上加载实际负载时的温升分布,建立有限元分析的零部件模型,重点对继电器的热分析模块进行优化。基于有限体积法的FLOEFD热仿真分析软件对整个熔断丝盒的温升分布进行仿真,并和实物试验结果进行对比分析,验证仿真分析模型的可靠性,对后续产品热设计的优化具有指导作用。 相似文献
9.
10.
11.
超宽混凝土桥面板是桥梁工程中的关键部位之一,其横向分块浇筑施工是提高桥面板质量的关键因素。结合一座宽61.7 m的超宽桥梁,采用MIDAS FEA有限元软件建立混凝土桥面板横向分块浇筑施工模型,分别对横向分2块浇筑、横向分4块由外向内浇筑、横向分6块由外向内浇筑、横向分6块先浇筑最外侧再浇筑最内侧最后浇筑中间块,4种施工方案进行计算对比,得到最佳施工方式为半幅横向分4块由外向内浇筑,与实际现场施工时采用的施工方法一致。 相似文献
12.
13.
14.
《JSAE Review》1995,16(3):263-268
Composite materials made of ceramics and metal are already used in heat resistant parts, such as pistons. Functionally gradient materials (FGM) are new composite materials that reduce the thermal stress caused by the difference of thermal expansion and that are resistant to super high temperature.In order to support the design of FGM, we have developed computer programs that analyze the transient heat transfer and the transient thermal stress of FGM by the finite element method (FEM). In this paper, the thermal stress analysis by these programs of an FGM plate, composed of Zr02 and Ti-6A1-4V, is discussed. 相似文献
15.
混凝土箱梁悬臂施工中温度梯度对标高影响的分析与控制 总被引:1,自引:0,他引:1
为研究混凝土箱梁悬臂施工阶段温度变形对成桥状态线形的影响,以苏北地区京杭大运河特大桥混凝土连续箱梁作为工程背景,进行了混凝土箱梁温度场的观测试验.在实测箱梁温度场数据的基础上,将传热学有限元分析结果与实测数据进行了比较.计算值和实测值吻合较好.从而验证了影响施工期间箱梁温度梯度的主要因素是太阳辐射强度和箱梁梗腋高度,定量确定了其与温度梯度之间的关系.研究表明,悬臂浇注施工箱梁温度梯度可以表达为太阳辐射强度和箱梁梗腋高度的函数,将计算温度梯度结果代入最大悬臂状态的计算模型中,可预测温度梯度对各节段箱梁立模标高的影响. 相似文献
16.
《JSAE Review》1994,15(2):133-140
The diesel combustion process has been simulated by an axisymmetric CFD computation for analyzing the wall heat transfer at elevated wall temperatures in heat insulated diesel engines and at conventional wall temperatures in normally cooled ones. A new model has been introduced in the computation to describe the reactive thermal boundary layers. The results show that in most cases tested the wall heat fluxes are lower at an elevated wall temperature than at a conventional wall temperature. It has been found, however, that the inclusion of deposits thermal resistance at a conventional wall temperture results in higher heat fluxes at an elevated wall temperature where the deposits are not formed. Besides, higher wall heat fluxes are estimated in heat insulated engines, if there is a large change in the combustion process due to a higher gas temperature. 相似文献
17.
18.
19.
为了准确分析轮毂电机温度场,基于电磁场有限元分析,采用考虑旋转磁化及谐波磁场的方法计算铁耗,并计算了轮毂电机各部件生热率。采用基于有限体积法的流固耦合分析和基于热网络法的磁热耦合分析,分别计算了额定工况下轮毂电机温度场,将轮毂电机温升试验和仿真结果进行了对比。结果表明,基于有限体积法的流固耦合分析得出的绕组稳态温度计算误差为1.8%,基于热网路法的磁热耦合分析计算误差为2.5%,验证了两种温度场分析方法的正确性。对不同结构冷却水道的热阻和压降进行了理论分析,基于Pareto遗传算法对螺旋型水道进行多目标优化,在保证额定工况电机稳态温升基本不变的情况下使水道压降降低了22.9%。 相似文献
20.
车辆传动装置部件温度的热网络计算方法 总被引:2,自引:0,他引:2
分析了车辆液力机械传动装置内部摩擦生热与传热过程,建立了完整的传动装置热网络模型,提出了基于热网络法的传动装置部件温度计算方法,确定了总体计算流程.对某型车辆液力机械传动装置部件温度进行了计算,得到了部件温度的详细分布,预测了传动装置中关键部件温度随大气环境温度的变化规律.计算结果与试验值符合较好,证实了该方法的有效性. 相似文献