Simulating the air quality impacts of traffic calming schemes in a dense urban neighborhood

In this study, the effects of isolated traffic calming measures and area-wide calming schemes on air quality in a dense neighborhood were estimated using a combination of microscopic traffic simulation, emission, and dispersion modeling. Results indicated that traffic calming measures did not have as large an effect on nitrogen dioxide (NO₂) concentrations as the effect observed on nitrogen oxide (NO_x) emissions. Changes in emissions resulted in highly disproportional changes in pollutant levels due to daily meteorological conditions, road geometry and orientation with respect to the wind. Average NO₂ levels increased between 0.1% and 10% with respect to the base-case while changes in NO_x emissions varied between 5% and 160%. Moreover, higher wind speeds decreased NO₂ concentrations on both sides of the roadway. Among the traffic calming measures, speed bumps produced the highest increases in NO₂ levels.     

A field evaluation case study of the environmental and energy impacts of traffic calming

This study quantifies the energy and environmental impact of a selection of traffic calming measures using a combination of second-by-second floating-car global positioning system data and microscopic energy and emission models. It finds that traffic calming may result in negative impacts on vehicle fuel consumption and emission rates if drivers exert aggressive acceleration levels to speed up to their journeys. Consequently by eliminating sharp acceleration maneuvers significant savings in vehicle fuel consumption and emission rates are achievable through driver education. The study also demonstrates that high emitting vehicles produce CO emissions that are up to 25 times higher than normal vehicle emission levels while low emitting vehicles produce emissions that are 15–35% of normal vehicles. The relative increases in vehicle fuel consumption and emission levels associated with the sample traffic calming measures are consistent and similar for normal, low, and high emitting vehicles.     

The significant impacts on traffic and emissions of ferrying children to school in Beijing

After having implemented numerous regulations, e.g., coercive policies on vehicle use and purchase, it is becoming increasingly difficult to find further potential to control vehicle emissions in Beijing, as the air quality is still poor. This research provides a different approach for policy-makers to reduce vehicle emissions by managing demand. We found that parents ferrying their children to and from school is an important but long-neglected contributor to traffic congestion and vehicle emissions. This phenomenon is very common in China because of the social culture. In this research, parallel tests during both the school season and the non-school season were adopted, and emissions in both seasons were calculated based on travel demand and emission models. The results revealed that emissions factors (in g/km) for criteria pollutants and CO₂ increased by over 10% during rush hours during the school season due to traffic condition deterioration compared with non-school season. Daily HC, CO, NO_x, PM and CO₂ emissions from the passenger car fleet were 8.3%, 7.8%, 6.4%, 6.3% and 6.5% higher compared with those during the non-school season, respectively. These differences are greater than the total vehicular emission reduction by other control measures in 2014 in Beijing. For policy makers, providing safe and efficient ways to ferry children would be a useful and harmonious strategy for future vehicle emission control.     

Energy use and emissions of two stroke-powered tricycles in Metro Manila

CO, CO₂, NO_x and HC emissions of two stroke-powered tricycles in Metro Manila are examined using an instantaneous emissions model. Results show that fuel consumption and HC emissions in middle class residential areas and main roads are similar but lower than levels in low income residential areas. On the average, tricycles in Metro Manila consume 24.41 km/l of fuel and produces 9.5, 9.7, 40.5 and 0.07 g/km of HC, CO, CO₂ and NO_x, respectively. They fail to satisfy HC, CO and NO_x emission limits set by reference standards in the Philippines and other Asian countries. They produce greater HC and CO emissions than gasoline fueled private cars and diesel powered public jeepneys, taxis and buses on a per passenger-km basis but significantly lower NO_x emissions. Tricycles account for 15.4% of the total HC emissions from mobile sources in the metropolis while their contributions to CO, CO₂ and NO_x are minimal.     

A velocity and payload dependent emission model for heavy-duty road freight transportation

The paper develops a forecasting model of emissions from traffic flows embracing the dynamics of driving behavior due to variations in payload. To measure of emissions at the level of individual vehicles under varying payloads a portable emission measurement system is used. This paper reports on a model based on data at the level of individual vehicles for a representative road trajectory. The model aggregates the data to the level of a homogeneous flow dependent of velocity and specific power, which is dependent on payload weight. We find a lean specification for the model that provides emission factors for CO₂, NO_x, HC, CO, and NO₂. The results indicate that, in comparison with earlier models, NO_x emissions in particular tend to be underestimated.     

Real-world gaseous emission characteristics of Euro 6b light-duty gasoline- and diesel-fueled vehicles

To accurately investigate vehicle emissions that have become major contributors to global air pollutants and greenhouse gases, test conditions have been transferred from laboratory type approval test cycles to real-world driving conditions. In this study, the real-world driving emissions of carbon monoxide (CO), total hydrocarbons (THC), nitrogen oxides (NO_x), and carbon dioxide (CO₂) from one gasoline and two diesel Euro 6b light-duty passenger vehicles were investigated by a portable emission measurement system (PEMS) in Lyon, France. NO_x and CO₂ emission controls remain critical to addressing the real-world driving emissions of Euro 6b vehicles. Notably, the tested gasoline vehicle emitted higher CO₂ emissions than diesel vehicles on all types of roads, especially on the urban road with an excess of 29.3–48.3%. The highest emission factors of gaseous pollutants generally occurred on the motorway for the gasoline vehicle, while on the urban road for diesel vehicles. In particular, for high-speed driving conditions, the gasoline vehicle gaseous emissions, especially NO_x emissions, were more affected by acceleration than diesel vehicle emissions. In addition, the CO emissions, especially THC emissions, for the gasoline vehicle, were more influenced by warm-start, especially cold-start, than those for diesel vehicles.     

Impacts of traffic-flows on vehicular-exhaust emissions at traffic junctions

This paper examines the impact of traffic-flow on CO, NO₂ and PM emissions at two distinct traffic junctions and evaluates the use of emission factors. The study includes three scenarios regarding pollutant emissions, which combine a field, experimental and semi-empirically estimated traffic parameters for free, interrupted and congested traffic-flow conditions. It evaluates the emission patterns for heterogeneity in traffic characteristics of both junctions. The results suggest the corrections to be made to emission factors at traffic junctions for better forecast of air quality.     

Assessing the importance of transportation activity data for urban emission inventories

The aim of this research is the implementation of a GPS-based modelling approach for improving the characterization of vehicle speed spatial variation within urban areas, and a comparison of the resulting emissions with a widely used approach to emission inventory compiling. The ultimate goal of this study is to evaluate and understand the importance of activity data for improving the road transport emission inventory in urban areas. For this purpose, three numerical tools, namely, (i) the microsimulation traffic model (VISSIM); (ii) the mesoscopic emissions model (TREM); and (iii) the air quality model (URBAIR), were linked and applied to a medium-sized European city (Aveiro, Portugal). As an alternative, traffic emissions based on a widely used approach are calculated by assuming a vehicle speed value according to driving mode. The detailed GPS-based modelling approach results in lower total road traffic emissions for the urban area (7.9, 5.4, 4.6 and 3.2% of the total PM10, NO_x, CO and VOC daily emissions, respectively). Moreover, an important variation of emissions was observed for all pollutants when analysing the magnitude of the 5th and 95th percentile emission values for the entire urban area, ranging from −15 to 49% for CO, −14 to 31% for VOC, −19 to 46% for NO_x and −22 to 52% for PM10. The proposed GPS-based approach reveals the benefits of addressing the spatial and temporal variability of the vehicle speed within urban areas in comparison with vehicle speed data aggregated by a driving mode, demonstrating its usefulness in quantifying and reducing the uncertainty of road transport inventories.     

An assessment of pollutant emissions due to air traffic at Nikola Tesla International Airport,Belgrade, and the link between local air quality and weather types

The assessment of local air pollution due to air traffic is an important issue from the standpoint of human health. An advanced approach using a landing and take-off cycle method is employed to assess emissions of nitrogen oxides (NO_x), carbon monoxide (CO), hydrocarbon (HC), and sulphur oxides (SO_x). Emissions of both volatile and non-volatile particulate matter are estimated using the new First-Order Approximation methodology. As synoptic situations (weather) determine the transport of pollutants in the air as well as their scavenging, the weather type for each day is classified for the study period (2008–2015).Due to a significant increase in air traffic at Nikola Tesla International Airport, Belgrade, in the last eight years, emissions of all considered pollutants have also increased. Emissions of NO_x and CO were the highest (totals for eight years were 2976.03 and 2875.66 tons, respectively). An analysis of weather types showed that the most frequent were warm, dry, anticyclones (AWD) and cyclones (low-pressure systems) including the passage of a cold front (CCF). The frequency of occurrence of AWDs and CCFs was 28.3% and 21.6%, respectively. An AWD is very unfavourable from the viewpoint of local air pollution, especially during the cold part of year, due to a shallow temperature inversion and fog formation in the morning confining the pollutants to the emission location for a longer time span. CCFs are also adverse due to the prevailing westerly and north-westerly winds that transport pollutants toward the city.     

Metropolitan sprawl measurement and its impacts on commuting trips and road emissions

This study measures urban form as indicators of metropolitan sprawl and explores its impact on commuting trips and NO_x and CO₂ emissions from road traffic in all metropolitan statistical areas (MSAs) and four groups’ MSAs separated by population in the continental United States. Encompassing all MSAs, the study adds the accessibility factor to four existing factors: density, land use mix, centeredness, and street connectivity. The study establishes multivariate regression models between urban form, commuting trips, and emissions from road traffic while controlling for socioeconomic conditions. The study shows that urban form index and five urban form factors have a statistically significant association with commuting trips, NO_x and CO₂ emissions from road traffic. In four MSA groups as determined by MSA population size, higher values of urban form factors (i.e., lower sprawl) are statistically associated with more walking commuters. On the other hand, higher values of urban form factors are associated with fewer commuting vehicles per household in large MSAs with the moderate effect, a lower average commuting drive time in medium and small MSAs, and more commuters using public transportation in medium and large MSAs. This study provides an urban form index covering all metropolitan areas in the continental United States by adding another urban form factor, and the findings show that urban form factors have different effects on mode choices, drive time, and emission from road traffic depending on the MSA population size.     

Exhaust emissions generated under actual operating conditions from a hybrid vehicle and an electric one fitted with a range extender

The paper describes exhaust emission tests performed on a PHEV (Plug-in Hybrid Electric Vehicle) and a BEV (Battery Electric Vehicle), in which the combustion engine was used as a range extender. The measurements of the exhaust emissions were performed for CO₂/fuel consumption, CO, THC and NO_x. The RDE measurements were performed including the engine operating parameters and emissions analysis. This analysis shows that the engines of BEVs and PHEVs operate in a different parameter range when under actual operating conditions, which directly translates into the exhaust emission values. This is particularly the case for the emission of NO_x. The investigations were carried out for two routes differentiated by the length and share of the urban and extra-urban cycles. For both routes, the emission of THC and CO were lower for the PHEV engine – HC by 69% (22 mg/km, route 1) and 6% (15 mg/km, route 2), CO by 69% (0.12 mg/km, route 1) and 80% (0.1 mg/km, route 2). For route 1, characterized by a greater share of the urban cycle, the emission of NO_x was lower by 70% (2 mg/km) for the BEV engine, and (route 2) lower by 60% (8 mg/km) for the PHEV engine. Additionally, the curves of the exhaust emissions in time for individual exhaust components have been presented that indicate that in the motorway cycle the emission of THC and CO from the BEV vehicle increases significantly up to ten times compared to urban cycle.     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.     

Light duty gasoline vehicle emission factors at high transient and constant speeds for short road segments

Vehicle emissions estimates are needed at high spatial and temporal resolution to estimate near-roadway air quality and human exposures. The MOBILE6 emission factor model is based on transient test cycles of less than 65 mph. Correction factors for high speed and constant speed are developed based on vehicle-specific power-based modal models for light duty gasoline vehicles, using data from portable emission measurement systems. At 80 mph versus 65 mph, the estimated average emission rates are greater by 30%, 20%, 80%, and 10% for NO_x, HC, CO, and CO₂. The ratio of constant to average of transient speed emission rates range from 0.49 to 0.94 for NO_x at speeds of 20 mph and 80 mph. The high speed and constant speed correction factors are applied to estimate vehicle emissions for a freeway segment that includes vehicle cruising speeds between 65 and 80 mph. The potential error for not accounting for constant speed operation on a short segment of highway could be 49% at moderate speed and 24% at high speed.     

Contrasting the direct use of data from traffic radars and video-cameras with traffic simulation in the estimation of road emissions and PM hotspot analysis

This study investigates the effect of traffic volume and speed data on the simulation of vehicle emissions and hotspot analysis. Data from a microwave radar and video cameras were first used directly for emission modelling. They were then used as input to a traffic simulation model whereby vehicle drive cycles were extracted to estimate emissions. To reach this objective, hourly traffic data were collected from three periods including morning peak (6–9 am), midday (11–2 pm), and afternoon peak (3–6 pm) on a weekday (June 23, 2016) along a high-volume corridor in Toronto, Canada. Traffic volumes were detected by a single radar and two video cameras operated by the Southern Ontario Centre for Atmospheric Aerosol Research. Traffic volume and composition derived from the radar had lower accuracy than the video camera data and the radar performance varied by lane exhibiting poorer performance in the remote lanes. Radar speeds collected at a single point on the corridor had higher variability than simulated traffic speeds, and average speeds were closer after model calibration. Traffic emissions of nitrogen oxides (NOx) and particulate matter (PM₁₀ and PM_2.5) were estimated using radar data as well as using simulated traffic based on various speed aggregation methods. Our results illustrate the range of emission estimates (NO_x: 4.0–27.0 g; PM₁₀: 0.3–4.8 g; PM_2.5: 0.2–1.3 g) for the corridor. The estimates based on radar speeds were at least three times lower than emissions derived from simulated vehicle trajectories. Finally, the PM₁₀ and PM_2.5 near-road concentrations derived from emissions based on simulated speeds were two or three times higher than concentrations based on emissions derived using radar data. Our findings are relevant for project-level emission inventories and PM hot-spot analysis; caution must be exercised when using raw radar data for emission modeling purposes.     

Reducing emissions at land border crossings through queue reduction and expedited security processing

Vehicle border crossings between Mexico and the United States generate significant amounts of air pollution, which can pose health threats to personnel at the ports of entry (POEs) as well as drivers, pedestrians, and local inhabitants. Although these health risks could be substantial, there is little previous work quantifying detailed emission profiles at POEs. Using the Mariposa POE in Nogales, Arizona as a case study, light-duty and heavy-duty vehicle emissions were analyzed with the objective of identifying effective emission reduction strategies such as inspection streamlining, physical infrastructure improvements, and fuel switching. Historical traffic information as well as field data were used to establish a simulation model of vehicle movement in VISSIM. Four simulation scenarios with varied congestion levels were considered to represent real-world seasonal changes in traffic volume. Four additional simulations captured varying levels of expedited processing procedures. The VISSIM output was analyzed using the EPA’s MOVES emission simulation software for conventional air pollutants. For the highest congestion scenario, which includes a 200% increase in vehicle volume, total emissions increase by around 460% for PM_2.5 and NO_x, and 540% for CO, SO₂, GHGs, and NMHC over uncongested conditions for a two-hour period. Expedited processing and queue reduction can reduce emissions in this highest congestion scenario by as much as 16% for PM_2.5, 18% for NO_x, 20% for NMHC, 7% for SO₂ and 15% for GHGs and CO. Other potential mitigation strategies examined include fleet upgrades, fuel switching, and fuel upgrades. Adoption of some or all of these changes would not only reduce emissions at the Mariposa POE, but would have air-quality benefits for nearby populations in both the US and Mexico. Fleet-level changes could have far-reaching improvements in air quality on both sides of the border.     

Individual exposure to traffic related air pollution across land-use clusters

In this study, we estimated the transportation-related emissions of nitrogen oxides (NO_x) at an individual level for a sample of the Montreal population. Using linear regression, we quantified the associations between NO_x emissions and selected individual attributes. We then investigated the relationship between individual emissions of NO_x and exposure to nitrogen dioxide (NO₂) concentrations derived from a land-use regression model. Factor analysis and clustering of land-uses were used to test the relationships between emissions and exposures in different Montreal areas. We observed that the emissions generated per individual are positively associated with vehicle ownership, gender, and employment status. We also noted that individuals who live in the suburbs or in peripheral areas generate higher emissions of NO_x but are exposed to lower NO₂ concentrations at home and throughout their daily activities. Finally, we observed that for most individuals, NO₂ exposures based on daily activity locations were often slightly more elevated than NO₂ concentrations at the home location. We estimated that between 20% and 45% of individuals experience a daily exposure that is largely different from the concentration at their home location. Our findings are relevant to the evaluation of equity in the generation of transport emissions and exposure to traffic-related air pollution. We also shed light on the effect of accounting for daily activities when estimating air pollution exposure.     

The effects of small roundabouts on emissions and fuel consumption: a case study

The effects of small roundabouts on emissions and fuel consumption were evaluated using the “car-following” method in a before/after study. The results showed that at a roundabout replacing a signalised junction, CO emissions decreased by 29%, NO_x emissions by 21% and fuel consumption by 28%. At roundabouts, replacing yield regulated junctions, CO emissions increased on average by 4%, NO_x emissions by 6% and fuel consumption by 3%. The results indicate that the large reductions in emissions and fuel consumption at one rebuilt signalised junction can “compensate for” the increase produced by several yield-regulated junctions rebuilt as roundabouts.     

How to best address aviation’s full climate impact from an economic policy point of view? – Main results from AviClim research project

The interdisciplinary research project AviClim (Including Aviation in International Protocols for Climate Protection) has explored the feasibility for including aviation’s full climate impact, i.e., both long-lived CO₂ and short-lived non-CO₂ effects, in international protocols for climate protection and has investigated the economic impacts. Short-lived non-CO₂ effects of aviation are NO_x emissions, H₂O emissions or contrail cirrus, for instance.Four geopolitical scenarios have been designed which differ concerning the level of international support for climate protecting measures. These scenarios have been combined alternatively with an emissions trading scheme on CO₂ and non-CO₂ species, a climate tax and a NO_x emission charge combined with CO₂ trading and operational measures (such as lower flight altitudes). Modelling results indicate that a global emissions trading scheme for both CO₂ and non-CO₂ emissions would be the best solution from an economic and environmental point of view. Costs and impacts on competition could be kept at a relatively moderate level and effects on employment are moderate, too. At the same time, environmental benefits are noticeable.     

Are HOV/eco-lanes a sustainable option to reducing emissions in a medium-sized European city?

Innovative traffic management measures are needed to reduce transportation-related emissions. While in Europe, road lane management has focused mainly on introduction of bus lanes, the conversion to High Occupancy Vehicles (HOV) and eco-lanes (lanes dedicated to vehicles running on alternative fuels) has not been studied comprehensively. The objectives of this research are to: (1) Develop an integrated microscopic modeling platform calibrated with real world data to assess both traffic and emissions impacts of future Traffic Management Strategies (TMS) in an urban area; (2) Evaluate the introduction of HOV/eco-lanes in three different types of roads, freeway, arterial and urban routes, in an European medium-sized city and its effects in terms of emissions and traffic performance. The methodology consists of three distinct phases: (a) Traffic and road inventory data collection; (b) Traffic and emissions simulation using an integrated platform of microscopic simulation; and (c) Evaluation of scenarios. For the baseline scenario, the statistical analysis shows valid results. The results show that HOV and eco-lanes in a medium European city are feasible, and when the Average Occupancy of Vehicles (AOV) increases, on freeways, the majority of vehicles can reduce their travel time (2%) with a positive impact in terms of total emissions (−38% NO_x, −39% HC, −43% CO and −37% CO₂). On urban and arterial corridors, the reduction in emissions could be achieved only if the AOV increases from 1.50 to 1.70 passengers/vehicle. Total emissions of the corridor with an AOV of 1.70 passengers/vehicle can be reduced up to 35–36% for the urban route while the values can be reduced by 36–39% for the arterial road. With the introduction of Hybrid Electric Vehicles (HEV) and Electric Vehicles (EV) it is possible to reduce emissions, although the introduction of eco-lanes did not show significant reductions in emissions. When both policies are simulated together, an emissions improvement is observed for the arterial route and for two of the scenarios.     

VISSIM/MOVES integration to investigate the effect of major key parameters on CO2 emissions

This paper looks at CO₂ emissions on limited access highways in a microscopic and stochastic environment using an optimal design approach. Estimating vehicle emissions based on second-by-second vehicle operation allows the integration of a microscopic traffic simulation model with the latest US Environmental Protection Agency’s mobile source emissions model to improve accuracy. A factorial experiment on a test bed prototype of the I-4 urban limited access highway corridor located in Orlando, Florida was conducted to identify the optimal settings for CO₂ emissions reduction and to develop a microscopic transportation emission prediction model. An exponentially decaying function towards a limiting value expressed in the freeway capacity is found to correlate with CO₂ emission rates. Moreover, speeds between 55 and 60 mph show emission rate reduction effect while maintaining up to 90% of the freeway’s capacity. The results show that speed has a significant impact on CO₂ emissions when detailed and microscopic analysis of vehicle operations of acceleration and deceleration are considered.