Performance of Low-bandwidth, Semi-active Damping Concepts for Suspension Control

Active damping has been shown to offer increased suspension performance in terms of vehicle isolation, suspension packaging, and road-tire contact force. It can even approximate the performance of full state feedback control without requiring the difficult measurement of tire deflection. Many semi-active damping strategies have been introduced to approximate the response of active damping with the modulation of passive damping parameters. These strategies have typically required a relatively high bandwidth for actuator response. This paper investigates the simulation performance and “frequency response” of two concepts in low-bandwidth semi-active suspension control, one that sets a damping force directly and another that sets the damping resistance. The electronically controlled bandwidth of these actuators is approximately an order of magnitude less than other semi-active devices; high frequency control is handled mechanically. A quarter-car model is studied with the controlled damping replacing both passive and active damping of typical control schemes. Both low-bandwidth damping strategies perform remarkably well compared to both active and high-bandwidth, semi-active damping. In certain dynamic performances, the new semi-active strategies outperform active damping and what the author calls “nominal” semi-active damping.     

Optimal Performance of Variable Component Suspensions

SUMMARY

Most vehicle suspension systems use fixed passive components that offer a compromise in performance between sprung mass isolation, suspension travel, and tireroad contact force. Recently, systems with discretely adjustable dampers and air springs been added to production vehicles. Active and semi-active damping concepts for vehicle suspensions have also been studied theoretically and with physical prototypes. This paper examines the optimal performance comparisons of variable component suspensions, including active damping and full-state feedback, for “quartercar” heave models. Two and three dimensional optimizations are computed using performance indicators to find the component parameters (control gains) that provide “optimal” performance for statistically described roadway inputs. The effects of performance weighting and feedback configuration are examined. Active damping is shown to be mainly important for vehicle isolation. A passive vehicle suspension can control suspension travel and tire contact force nearly as well as a full state feedback control strategy.     

Semi-Active Suspension with Preview Using a Frequency-Shaped Performance Index

SUMMARY

The objective of this study is to develop a control law for a semi-active suspension for the purpose of ride quality improvement. The semi-active control law is determined by reproducing the control force of an optimally controlled active suspension while suppressing its damping coefficient variation. The performance index of the optimal control for the active suspension is modified to include frequency-shaping by use of Parseval's theorem, which allows us to de-emphasize the effects of particular variables over specific frequency bands.

Through the numerical simulations, it was found that the semi-active suspension may reduce the vertical acceleration of the driver's seat and the sprung mass motions significantly. The road-holding and tire deflections were not affected much.     

Experimental Verification of Resistance Control, Semi-Active Damping

Electronically controlled vehicle suspensions offer substantial improvements in performance over conventional, passive suspensions but with the price of power, complexity, and actuating bandwidth. Low-bandwidth, semi-active damping addresses the problems of power and bandwidth by using low power modulation of controllable dampers at the frequency of the isolated mass. Resistance controlled, semi-active damping is experimentally verified to better sprung mass isolation while reducing suspension stroke, something that a passive system cannot do. It is also shown to compare reasonably well with computer simulation results. The experimental implementation is a 1/30 scale, two degree-of-freedom test bed that represents the standard quarter vehicle model.     

Semi-Active Suspension with Preview Using a Frequency-Shaped Performance Index

The objective of this study is to develop a control law for a semi-active suspension for the purpose of ride quality improvement. The semi-active control law is determined by reproducing the control force of an optimally controlled active suspension while suppressing its damping coefficient variation. The performance index of the optimal control for the active suspension is modified to include frequency-shaping by use of Parseval's theorem, which allows us to de-emphasize the effects of particular variables over specific frequency bands.

Through the numerical simulations, it was found that the semi-active suspension may reduce the vertical acceleration of the driver's seat and the sprung mass motions significantly. The road-holding and tire deflections were not affected much.     

Optimal Performance of Variable Component Suspensions

Most vehicle suspension systems use fixed passive components that offer a compromise in performance between sprung mass isolation, suspension travel, and tireroad contact force. Recently, systems with discretely adjustable dampers and air springs been added to production vehicles. Active and semi-active damping concepts for vehicle suspensions have also been studied theoretically and with physical prototypes. This paper examines the optimal performance comparisons of variable component suspensions, including active damping and full-state feedback, for “quartercar” heave models. Two and three dimensional optimizations are computed using performance indicators to find the component parameters (control gains) that provide “optimal” performance for statistically described roadway inputs. The effects of performance weighting and feedback configuration are examined. Active damping is shown to be mainly important for vehicle isolation. A passive vehicle suspension can control suspension travel and tire contact force nearly as well as a full state feedback control strategy.     

半主动悬架的滑模变结构控制

针对带有电流变液智能阻尼器的半主动汽车悬架模型,运用滑模变结构方法设计了半主动悬架滑模控制器。根据滑模运动方程稳定的Hurwitz判据选择滑模面系数,用指数趋近率改善滑模运动段的动态品质并进一步确定了半主动悬架的实时控制阻尼力。对多种激励信号下隔振质量的响应及半主动悬架系统在系统参数摄动下的鲁棒特性进行了仿真分析。结果表明:变结构控制下半主动悬架系统的隔振效果要远好于最优被动系统,而且对外界扰动有一定的适应性,对系统参数摄动也具有很强的鲁棒性。     

Optimal Linear Active Suspensions with Vibration Absorbers and Integral Output Feedback Control

SUMMARY

The bandwidth of the body response to a road input in an active suspension may be considerably reduced if the axle motions are independently controlled and if, at the same time, the effects of static and dynamic loads are counteracted by integral action in the body force control system. The paper presents a further application of the Ferguson-Rekasius method, leading to optimal output control with incomplete state feedback. To achieve narrow bandwidth body response the support springs are replaced by hydraulic actuators, and vibration absorbers or active wheel dampers are employed for the control of the axle motions. Active wheel damping is the more effective and gives good results. Proportional-plus-integral control action is shown to reduce the transient body displacements due to external forces.     

State of the art survey: active and semi-active suspension control

This survey paper aims to provide some insight into the design of suspension control system within the context of existing literature and share observations on current hardware implementation of active and semi-active suspension systems. It reviews the performance envelop of active, semi-active, and passive suspensions with a focus on linear quadratic-based optimisation including a specific example. The paper further discusses various design aspects including other design techniques, the decoupling of load and road disturbances, the decoupling of pitch and heave modes, the use of an inerter as an additional design element, and the application of preview. Various production and near production suspension systems were examined and described according to the features they offer, including self-levelling, variable damping, variable geometry, and anti-roll damping and stiffness. The lessons learned from these analytical insights and related hardware implementations are valuable and can be applied towards future active or semi-active suspension design.     

Comparison of the properties of active and semiactive suspension

In this article, the properties of active and semi-active suspension for heavy goods vehicles are compared. The criteria for the comparison are the RMS sprung mass vertical acceleration, RMS dynamic tyre force, and suspension power consumption. The active system is based on an air-spring with controlled in-flow and out-flow of the air. In the semi-active system, a controlled hydraulic damper is employed. The results concerning the semi-active suspension system were taken from the article by Besinger et al. [Besinger, F.H., Cebon, D. and Cole, D.J., 1995, Force control of a semi-active damper. Vehicle System Dynamics, 24(9), 695–723.].     

基于闭环力反馈原理的非线性液压主动阻尼悬架模型的研究及优化设计

本文在理论上建立了一套基于主动力反馈原理的新型主动阻尼悬架的设计和优化方法。首先提出了该主动阻尼悬架的实现模型，该模型是在传统的液力减振器的基础上，应用半主动控制的思想，结合力反馈的原理建立起来的内部液压反馈阻尼网络模型。理论优化分析和计算机仿真表明，通过该液阻网络模型，即可以实现电控的主动阻尼悬架的功能，它可以根据汽车行驶路况的好坏，自适应地调节悬架阻尼大小以实现主动阻尼悬架的最优控制。     

Skyhook and H8 Control of Semi-active Suspensions: Some Practical Aspects

Summary This paper deals with single-wheel suspension car model. We aim to prove the benefits of controlled semi-active suspensions compared to passive ones. The contribution relies on H 8 control design to improve comfort and road holding of the car under industrial specifications, and on control validation through simulation on an exact nonlinear model of the suspension. Note that we define semi-active suspensions as control systems incorporating a parallel spring and an electronically controlled damper. However, the type of damper used in automotive industry can only dissipate energy. No additional force can be generated using external energy. The control issue is then to change, in an accurate way, the damping (friction) coefficient in real-time. This is what we call semi-active suspension. For this purpose, two control methodologies, H 8 and Skyhook control approaches, are developed, using a linear model of the suspension, and compared in terms of performances using industrial specifications. The performance analysis is done using the control-oriented linear model first, and then using an exact nonlinear model of the suspension incorporating the nonlinear characteristics of the suspension spring and damper.     

Active Control of Non-stationary Response of Vehicles with Nonlinear Suspensions

SUMMARY

Active control of non-stationary response of a single degree of freedom vehicle model with nonlinear passive suspension elements is considered in this paper. The method of equivalent linearization is used to derive the equivalent linear model and the optimal control laws are obtained by using stochastic optimal control theory based on full state information. Velocity squared quadratic damping and hysteresis type of stiffness nonlinearities are considered. The effect of the nonlinearities on the active system performance is studied. The performance of active suspensions with nonlinear passive elements is found to be superior to the corresponding passive suspension systems.     

Skyhook and H8 Control of Semi-active Suspensions: Some Practical Aspects

Summary This paper deals with single-wheel suspension car model. We aim to prove the benefits of controlled semi-active suspensions compared to passive ones. The contribution relies on H 8 control design to improve comfort and road holding of the car under industrial specifications, and on control validation through simulation on an exact nonlinear model of the suspension. Note that we define semi-active suspensions as control systems incorporating a parallel spring and an electronically controlled damper. However, the type of damper used in automotive industry can only dissipate energy. No additional force can be generated using external energy. The control issue is then to change, in an accurate way, the damping (friction) coefficient in real-time. This is what we call semi-active suspension. For this purpose, two control methodologies, H 8 and Skyhook control approaches, are developed, using a linear model of the suspension, and compared in terms of performances using industrial specifications. The performance analysis is done using the control-oriented linear model first, and then using an exact nonlinear model of the suspension incorporating the nonlinear characteristics of the suspension spring and damper.     

Generalized magnetorheological (MR) damper model and its application in semi-active control of vehicle suspension system

In this paper, analytical characterization of the magneto-rheological (MR) damper is done using a new modified algebraic model. Algebraic model is also more preferable because of its low computational expenses compared to differential Bouc-Wen’s model which is highly computationally demanding. This model along with the obtained model parameters is used as a semi-active suspension device in a quarter car model and the stationary response of the vehicle traversing on a rough road is obtained. The control part consists of two nested controllers. One of them is the system controller which generates the desired damping force and the other is the damper controller which adjusts the voltage level to MR damper so as to track the desired damping force. For the system controller a model reference skyhook Sliding Mode Controller (SMC) is used and for the damper controller a continuous state algorithm is built to determine the input voltage so as to gain the desired damping force. The analytical model is subsequently used in the quarter car vehicle model and the vehicular responses are studied. A simulation study is performed to prove the effectiveness and robustness of the semi-active control approach. Results show that the semi-active controller can achieve compatible performance as that of active suspension controller except for a little deterioration.     

Semi-Active Control Laws - Optimal and Sub-Optimal

SUMMARY

This paper attempts to clarify the question of what the optimal semi-active suspension is that minimizes a deterministic quadratic performance index. The optimal control law is a time-varying solution that involves three related Riccati equations. The constant Riccati solution (the so-called “clipped optimal” solution) is not optimal, although its performance is generally quite close to that of the time-varying solution. As the time-varying solution cannot be practically implemented, several constant gain sub-optimal solutions are investigated. A new semi-active algorithm, called the “steepest gradient” algorithm, is developed and its performance is shown to be superior to that of the “clipped optimal” solution.     

电动赛车半主动悬架系统仿真及实现

应用汽车动力学理论,以1/4汽车悬架模型为研究对象,用调节减振器的阻尼系数法,建立了二自由度电动赛车的半主动悬架最优控制模型,利用编制的路面谱作为激励输入进行了仿真,并与被动悬架性能进行了对比。结果表明,半主动悬架在车身垂直振动加速度、悬架动行程、轮胎形变量的改善度分别为31.3%、21.4%、12.6%,使车身的振动被控制在某个范围之内,大大提高电动赛车在行驶过程中的平顺性。     

Adaptive Suspension Concepts for Road Vehicles

SUMMARY

Most vehicle suspensions are composed of passive spring and damper devices, although improved suspension performance is possible if an active system is used to control forces or relative velocities. The complexity, power requirements, and cost of fully active suspensions have restricted their use. Various partially active suspensions have been proposed and suspensions with slow load levelers and variable dampers are in widespread use. Here we analyze a class of basically passive suspensions the parameters of which can be varied actively in response to various measured signals on the vehicle. These suspensions can come close to optimal performance with simpler means than many of the active or semi-active schemes previously proposed.     

The Response of Active and Semi-active Suspensions to Realistic Feedback Signals

SUMMARY

A simple vehicle model is presented incorporating passive, active, and semi-active suspensions. When the desired feedback variables are ideally available, the system response is well understood and excellent sprung mass isolation results. More often than not, the measured variables must be signal processed in some manner prior to their use in some control algorithm. This paper presents the expected response of a simple vehicle with an active and/or semi-active suspension, subject to non-ideal feedback information.     

电流变智能半主动悬架模糊PID控制

对带有电流变液智能阻尼器的半主动汽车悬架系统设计了一种模糊PID控制器。将半主动悬架簧载质量的位移及其导数作为模糊控制器的输入，PID控制器的3个增益参数作为其输出，利用电流变液智能阻尼器的阻尼力可随电压变化的特性来使车身的振动降为最小。仿真实验给出了最优被动悬架、固定参数PID控制智能半主动悬架和模糊PID控制智能半主动悬架在不同路面激励情况下的响应曲线。