Commuters’ exposure to PM2.5 and CO2 in metro carriages of Shanghai metro system

Air quality inside transportation carriages has become a public concern. A comprehensive measurement campaign was conducted to examine the commuters’ exposure to PM_2.5 (d_p ⩽ 2.5 μm) and CO₂ in Shanghai metro system under different conditions. The PM_2.5 and CO₂ concentrations inside all the measured metro lines were observed at 84 ± 42 μg/m³ and 1253.1 ± 449.1 ppm, respectively. The factors that determine the in-carriage PM_2.5 and CO₂ concentrations were quantitatively investigated. The metro in-carriage PM_2.5 concentrations were significantly affected by the ventilation systems, out-carriage PM_2.5 concentrations and the passenger numbers. The largest in-carriage PM_2.5 and CO₂ concentrations were observed at 132 μg/m³ and 1855.0 ppm inside the carriages equipped with the oldest ventilation systems. The average PM_2.5 and CO₂ concentrations increased by 24.14% and 9.93% as the metro was driven from underground to overground. The average in-carriage PM_2.5 concentrations increased by 17.19% and CO₂ concentration decreased by 16.97% as the metro was driven from urban to the suburban area. It was found that PM_2.5 concentration is proportional to the on-board passenger number at a ratio of 0.4 μg/m³·passenger. A mass-balance model was developed to estimate the in-carriage PM_2.5 concentration under different driving conditions.     

How wide should be the adjacent area to an urban motorway to prevent potential health impacts from traffic emissions?

In recent years, several studies show that people who live, work or attend school near the main roadways have an increased incidence and severity of health problems that may be related with traffic emissions of air pollutants. The concentrations of near-road atmospheric pollutants vary depending on traffic patterns, environmental conditions, topography and the presence of roadside structures. In this study, the vertical and horizontal variation of nitrogen dioxide (NO₂) and benzene (C₆H₆) concentration along a major city ring motorway were analysed. The main goal of this study is to try to establish a distance from this urban motorway considered “safe” concerning the air pollutants human heath limit values and to study the influence of the different forcing factors of the near road air pollutants transport and dispersion. Statistic significant differences (p = 0.001, Kruskal–Wallis test) were observed between sub-domains for NO₂ representing different conditions of traffic emission and pollutants dispersion, but not for C₆H₆ (p = 0.335). Results also suggest significant lower concentrations recorded at 100 m away from roadway than at the roadside for all campaigns (p < 0.016 (NO₂) and p < 0.036 (C₆H₆), Mann–Whitney test). In order to have a “safe” life in homes located near motorways, the outdoor concentrations of NO₂ must not exceed 44–60.0 μg m⁻³ and C₆H₆ must not exceed 1.4–3.3 μg m⁻³. However, at 100 m away from roadway, 81.8% of NO₂ receptors exceed the annual limit value of human health protection (40 μg m⁻³) and at the roadside this value goes up to 95.5%. These findings suggest that the safe distance to an urban motorway roadside should be more at least 100 m. This distance should be further studied before being used as a reference to develop articulated urban mobility and planning policies.     

Evaluating the social cost of cruise ships air emissions in major ports of Greece

Detailed NO_x, SO₂ and PM_2.5 emissions have been estimated for cruise ships in the five busiest Greek ports (i.e. Piraeus, Santorini, Mykonos, Corfu and Katakolo) for year 2013. The emissions were analyzed in terms of gas species, seasonality and activity. The total in-port inventory of cruise shipping accounted to 2742.7 tons: with NO_x being dominant (1887.5 tons), followed by SO₂ and PM_2.5 (760.9 and 94.3 tons respectively). Emissions during hotelling corresponded to 88.5% of total and have significantly outweighed those produced during ships’ maneuvering activities (11.5% of total). Seasonality was found to play a major role, as summer emissions and associated impacts were significantly augmented. The anticipated health impacts of ship emissions can reach to €24.3 million or to €5.3 per passenger proving the necessity of control of the emissions produced by cruise ships in port cities or policy and measures towards a more efficient cruise industry.     

Estimation of nitrogen oxides emissions from petrol and diesel passenger cars by means of on-board monitoring: Effect of vehicle speed,vehicle technology,engine type on emission rates

NO_X emission rates of 13 petrol and 3 diesel passenger cars as a function of average speed from 10 to 120 km/h, emission class (pre-Euro 1 – Euro 5), engine type were investigated by on-board monitoring on roads and highways of St. Petersburg using a portative Testo XXL 300 gas analyzer. The highest level of NO_X emission 0.5–2.5 g/km was inherent to old pre-Euro 1 petrol cars without a catalytic converter. NO_X emissions rates of Euro 1 and Euro 2 petrol cars changed within 0.15–0.9 g/km, Euro 3 – 0.015–0.27 g/km, Euro 4 – 0.013–0.1 g/km, Euro 5 – 0.002–0.043 g/km. Euro 3 – Euro 4 petrol cars generally satisfied corresponding NO_X Emission Standards (ES), except cold-start period, Euro 5 petrol cars did not exceed ES. Warmed, stabilized engines of Euro 3 – Euro 5 petrol cars showed 5–10 times lower NO_X emission rates than corresponding ES in the range of speed from 20 to 90 km/h. NO_X emission rates of diesel Euro 3 and Euro 4 cars varied from 0.45 to 1.1 g/km and from 0.31 to 1.1 g/km, respectively. Two examined diesel Euro 3 and one Euro 4 passenger vehicles did not satisfy NO_X ES at real use. Euro 3 diesel cars showed 28.9 times higher NO_X emissions than Euro 3 petrol cars and Euro 4 diesel car demonstrated 17.6 times higher NO_X emissions than Euro 4 petrol cars at warmed and stabilized engine at a cruise speed ranging from 30 to 60 km/h.     

Effects of the 80 km/h and variable speed limits on air pollution in the metropolitan area of barcelona

In 2008 the regional government of Catalonia (Spain) reduced the maximum speed limit on several stretches of congested urban motorway in the Barcelona metropolitan area to 80 km/h, while in 2009 it introduced a variable speed system on other stretches of its metropolitan motorways. We use the differences-in-differences method, which enables a policy impact to be measured under specific conditions, to assess the impact of these policies on emissions of NO_x and PM₁₀. Empirical estimation indicate that reducing the speed limit to 80 km/h causes a 1.7–3.2% increase in NO_x and 5.3–5.9% in PM₁₀. By contrast, the variable speed policy reduced NO_x and PM₁₀ pollution by 7.7–17.1% and 14.5–17.3%. As such, a variable speed policy appears to be a more effective environmental policy than reducing the speed limit to a maximum of 80 km/h.     

Regional climate impact of aerosols emitted by transportation modes and potential effects of policies on demand and emissions

The transportation system is one of the main sectors with significant climate impact. In the U.S. it is the second main emitter of carbon dioxide. Its impact in terms of emission of carbon dioxide is well recognized. But a number of aerosol species have a non-negligible impact. The radiative forcing due to these species needs to be quantified. A radiative transfer code is used. Remote sensing data is retrieved to characterize different regions. The radiative forcing efficiency for black carbon are 396 ± 200 W/m²/AOD for the ground mode and 531 ± 190 W/m²/AOD for the air transportation, under clear sky conditions. The radiative forcing due to contrail is 0.14 ± 0.06 W/m² per percent coverage. Based on the forcing from the different species emitted by each mode of transportation, policies may be envisioned. These policies may affect demand and emissions of different modes of transportation. Demand and fleet models are used to quantify these interdependencies. Depending on the fuel price of each mode, mode shifts and overall demand reduction occur, and more fuel efficient vehicles are introduced in the fleet at a faster rate. With the introduction of more fuel efficient vehicles, the effect of fuel price on demand is attenuated. An increase in fuel price of 50 cents per gallon, scaled based on the radiative forcing of each mode, results in up to 5% reduction in emissions and 6% reduction in radiative forcing. With technologies, significant reduction in climate impact may be achieved.     

On the electrification of road transportation – A review of the environmental,economic, and social performance of electric two-wheelers

Electrification is widely considered as a viable strategy for reducing the oil dependency and environmental impacts of road transportation. In pursuit of this strategy, most attention has been paid to electric cars. However, substantial, yet untapped, potentials could be realized in urban areas through the large-scale introduction of electric two-wheelers. Here, we review the environmental, economic, and social performance of electric two-wheelers, demonstrating that these are generally more energy efficient and less polluting than conventionally-powered motor vehicles. Electric two-wheelers tend to decrease exposure to pollution as their environmental impacts largely result from vehicle production and electricity generation outside of urban areas. Our analysis suggests that the price of e-bikes has been decreasing at a learning rate of 8%. Despite price differentials of 5000 ± 1800 EUR₂₀₁₂ kW h⁻¹ in Europe, e-bikes are penetrating the market because they appear to offer an apparent additional use value relative to bicycles. Mid-size and large electric two-wheelers do not offer such an additional use value compared to their conventional counterparts and constitute niche products at price differentials of 700 ± 360 EUR₂₀₁₂ kW⁻¹ and 160 ± 90 EUR₂₀₁₂ kW⁻¹, respectively. The large-scale adoption of electric two-wheelers can reduce traffic noise and road congestion but may necessitate adaptations of urban infrastructure and safety regulations. A case-specific assessment as part of an integrated urban mobility planning that accounts, e.g., for the local electricity mix, infrastructure characteristics, and mode-shift behavior, should be conducted before drawing conclusions about the sustainability impacts of electric two-wheelers.     

Preliminary investigation of PM1, PM2.5, PM10 and its metal elemental composition in tunnels at a subway station in Shanghai,China

In this study, real-time monitoring campaigns were conducted in two tunnels (Line A and Line B) at a subway station in Shanghai, including temperature, relative humidity, PM₁, PM_2.5 and PM₁₀, in order to understand the climate and PM characteristics in the transportation microenvironment. In addition, collected floor dust particles in the tunnel were analyzed by ICP for their metal elemental composition. Strong correlations occurred between all PM levels and meteorological parameters in the tunnel of Line A (with platform screen doors), in comparison with the weak correlations between such parameters in the tunnel of Line B (without platform screen doors). PM_2.5 and PM₁₀ between peak hours and off-peak hours for both lines presented significant differences (p < 0.05), respectively. Nevertheless, PM₁ showed a different pattern, with p > 0.05 for Line A and p < 0.05 for Line B, respectively. In addition, statistical results concluded that PM had an evident weekly variation for both lines. Friday was the highest day of all particulate matters in monitoring periods for both lines. Ratios of PM₁/PM₁₀ and PM_2.5/PM₁₀ were high when trains were out of service and low when trains were in service. Relative abundance of metal elements detected from floor dust particles proved that floor dust particles in tunnels might be a major source of airborne PM in the subway microenvironments, with Fe as the most abundant metal element, followed by Ca, Al, Mg, Mn, Zn, Cu, Cr, Ni, Pb and Hg.     

Isocyanic acid and ammonia in vehicle emissions

Vehicles are considered to be an important source of ammonia (NH₃) and isocyanic acid (HNCO). HNCO and NH₃ have been shown to be toxic compounds. Moreover, NH₃ is also a precursor in the formation of atmospheric secondary aerosols. For that reason, real-time vehicular emissions from a series of Euro 5 and Euro 6 light-duty vehicles, including spark ignition (gasoline and flex-fuel), compression ignition (diesel) and a plug-in electric hybrid, were investigated at 23 and −7 °C over the new World harmonized Light-duty vehicle Test Cycle (WLTC) in the Vehicle Emission Laboratory at the European Commission Joint Research Centre Ispra, Italy. The median HNCO emissions obtained for the studied fleet over the WLTC were 1.4 mg km⁻¹ at 23 °C and 6 mg km⁻¹ at −7 °C. The fleet median NH₃ emission factors were 10 mg km⁻¹ and 21 mg km⁻¹ at 23 and −7 °C, respectively. The obtained results show that even though three-way catalyst (TWC), selective catalytic reduction (SCR), and NOx storage catalyst (NSC) are effective systems to reduce NOx vehicular emissions, they also lead to considerable emissions of the byproducts NH₃ and/or HNCO. It is also shown that diesel light-duty vehicles equipped with SCR can present NH₃ emission factors as high as gasoline light-duty vehicles at both, 23 and −7 °C over the WLTC. Therefore, with the introduction in the market of this DeNOx technology, vehicular NH₃ emissions will increase further.     

Personal exposures to PM during short distance highway travel in India

Traffic is the largest contributor (37%) to urban air pollution in India. During commuting, passengers are significantly exposed to pollutants. We carried out a study on a National Highway (NH) in India to measure personal exposure to Particulate Matter (PM) in five travel modes. PM_2.5 concentrations showed the following trend: Bus > Car FA (fresh air mode of air condition) > Bus AC > Car > Car RC (re-circulation mode of air condition). Highest and lowest concentrations of PM₁₀ were observed in Bus (134 ± 47 µg m⁻³) and Car RC (20 ± 5 µg m⁻³), respectively. The exposures were highest at the rear seats during the Bus AC journeys. In Car FA, the contribution of PM₁ to total concentrations was dominant (61%). Travel modes explained highest variabilities in PM₁₀, PM_2.5 and PM₁ concentrations. In all travel modes, the highest particle counts were observed for PM_0.3–0.5. PM_>0.5–5.0 counts during Bus journeys were comparatively higher than remaining modes. Deposition doses of passengers were as high as 3.22 µg of PM₁₀ (in Bus), 0.66 µg of PM_2.5 (in Bus) and 0.06 µg of PM₁ (in Bus AC) during the ~1 h journey. Our study revealed that Car RC is the safest mode of travel, both in terms of personal exposures and PM depositions in respiratory system. The results from this study can be used to target efforts to reduce personal exposure of highway commuters.     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

Energy use and emissions of two stroke-powered tricycles in Metro Manila

CO, CO₂, NO_x and HC emissions of two stroke-powered tricycles in Metro Manila are examined using an instantaneous emissions model. Results show that fuel consumption and HC emissions in middle class residential areas and main roads are similar but lower than levels in low income residential areas. On the average, tricycles in Metro Manila consume 24.41 km/l of fuel and produces 9.5, 9.7, 40.5 and 0.07 g/km of HC, CO, CO₂ and NO_x, respectively. They fail to satisfy HC, CO and NO_x emission limits set by reference standards in the Philippines and other Asian countries. They produce greater HC and CO emissions than gasoline fueled private cars and diesel powered public jeepneys, taxis and buses on a per passenger-km basis but significantly lower NO_x emissions. Tricycles account for 15.4% of the total HC emissions from mobile sources in the metropolis while their contributions to CO, CO₂ and NO_x are minimal.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Environmental,functional and economic criteria for comparing “target roundabouts” with one- or two-level roundabout intersections

The article describes a criterion based on functional, environmental and economic aspects for comparing conventional roundabouts with innovative one- or two-level roundabouts. We compared the performances of eight roundabout types, differing in geometric layout, number of lanes and traffic flow regulation from each other, with regard to vehicle delays and CO₂, NO_x, PM_2.5 and PM₁₀ pollutant emissions. Recently-designed roundabouts – target roundabouts and flyover roundabouts – have also been studied for their undoubted practical interest. By means of closed-form capacity models and CORINAIR methodology, several traffic simulations were carried out to examine a typical annual traffic demand curve in a suburban context, three different distribution test matrices for traffic flows (ρ1, ρ2, ρ3) and maximum annual traffic flow values Q_max ranging between 1300 and 3300 veh/h.Estimating vehicle delays and annual pollutant emissions, along with construction and management costs, allowed obtaining overall costs for each roundabout examined, in function of traffic demand and several other parameters. Thanks to these analyses, we identified the roundabout types which best suit to each traffic condition.     

Truck versus pipeline transportation cost analysis of wastewater sludge

Domestic and industrial sludge generated at wastewater treatment facilities is considered a potential biomass source for producing biodiesel. However, transportation of large amounts of sludge from wastewater treatment facilities to a biorefinery is expensive. The objective of this paper is to identify the proper transportation mode to use as a function of the volume shipped and transportation distances. Currently, sludge is mainly shipped by truck and pipeline. We estimated that the fixed and variable cost components of pipeline transportation for a volume such as 480 m³/day and a distance of 100 miles are $0.116/m³ and $0.089/m³/mile, respectively. We estimated the biomass (sludge) transportation cost per gallon of biodiesel, and observed the changes in these costs as a function of distance traveled and volume shipped. The outcomes of this study have the potential to help biofuel plants make better biomass transportation decisions, and consequently reduce the price of biodiesel significantly.     

Characteristics of particulate matter (PM) concentrations influenced by piston wind and train door opening in the Shanghai subway system

More than 9 million passengers take Shanghai’s subway system every work day. The system’s air quality has caused widespread concern because of the potential harm to passengers’ health. We measured the particulate matter (PM) concentrations at three kinds of typical underground platform (side-type, island-type, and stacked-type platforms) and inside the trains in Shanghai’s metro during 7 days of measurements in April and July 2015. Our results demonstrated that the patterns of air quality variation and PM concentrations were similar at the side-type and island-type platforms. We also found that the PM concentrations were higher on the platforms than inside the train and that the PM concentrations in the subway system were positively correlated with those in the ambient air. Piston wind generated by vehicle motion pushes air from the tunnel to the platform, so platform PM concentrations increase when trains approach the platform. However, the piston wind effect varies greatly between locations on the platform. In general, the effect of the piston wind is weaker at the middle of the platform than at both ends. PM concentrations inside the train increase after the doors open, during which time dirty platform air floods into the compartments. PM_1.0 and PM_2.5 were significantly correlated both inside the train and on the platforms. PM_1.0 accounted for 71.9% of PM_2.5 inside the train, which is higher than the corresponding platform values. Based on these results, we propose some practical suggestions to minimize air pollution damage to passengers and staff from the subway system.     

Analyzing fluctuations in car-following

Many car-following models predict a stable car-following behavior with a very small fluctuation around an equilibrium value g¹ of the net headway g with zero speed-difference Δv between the following and the lead vehicle. However, it is well-known and additionally demonstrated by data in this paper, that the fluctuations are much larger than these models predict. Typically, the fluctuation in speed difference is around ±2 m/s, while the fluctuation in the net time headway T = g/v can be as big as one or even two seconds, which is as large as the mean time headway itself. By analyzing data from loop detectors as well as data from vehicle trajectories, evidence is provided that this randomness is not due to driver heterogeneity, but can be attributed to an internal stochasticity of the driver itself. A final model-based analysis supports the hypothesis, that the preferred headway of the driver is the parameter that is not kept constant but fluctuates strongly, thus causing the even macroscopically observable randomness in traffic flow.     

A model for evaluating the environmental and functional benefits of “innovative” roundabouts

This study looks at the singling out of a multi-parameter criterion for choosing conventional or innovative roundabout layouts, by taking functional, environmental and economic aspects into consideration. The performances of three conventional roundabouts (with different lane number at entries and through the ring), turbo-roundabouts and roundabouts with right-turn bypass lane on all the arms (flower roundabouts) have been compared in terms of vehicle delays and pollutant (carbon dioxide, nitrogen oxides, particle pollution (PM₁₀ and PM_2.5)) emissions. By means of closed-form capacity models and with the help of COPERT IV^© software, several traffic simulations have been carried out, referred to yearly peak flow values Q_max and ranging between 1300 and 3300 veh/h, starting from a typical annual traffic demand curve in urban areas. The estimation of cumulative vehicle delays and annual pollutant emissions, together with construction and maintenance costs has allowed working out overall costs for each roundabout under consideration, depending on the traffic demand. Thus, the proposed model allows finding the most cost-effective geometric solution as to overall costs for a comprehensive case record of traffic values.     

Estimating the CO2 intensity of intermodal freight transportation

This paper looks at the environmental effects of shifting from road to rail freight transportation. Little data is available to shippers to calculate the potential CO₂ savings of an intermodal shift. In this paper we analyze a data set of more than 400,000 intermodal shipments to calculate the CO₂ intensity of intermodal transportation as a distinct mode. Our results indicate an average intensity of 67 g of CO₂ per ton-mile, but can vary between 29 and 220 g of CO₂ per ton-mile depending on the specific origin–destination lane. We apply the market area concept to explain the variance between individual lane intensities and demonstrate the complexity in predicting the potential carbon savings in a switch from truckload to intermodal.