Effect on direct injection naturally aspirated diesel engine characteristics fuelled by pine oil,ceiba pentandra methyl ester compared with diesel

This paper explores the experimental investigation of the performance, emission and combustion characteristics of bio fuels from ceiba pentandra methyl ester (CPME), ceiba pentandra methyl ester-pine oil blends (CPMEP) and pine oil and the results are compared with diesel. In ceiba pentandra seed oil the CPME yield is 92% by using transesterification process with the optimum conditions of 560 rpm, reaction time 58 min, catalyst concentration 13 g and methanol amount 500 ml. The viscosity of CPME is high when compare with diesel. So the low viscosity of pine oil is blended with CPME and it can be directly used in diesel engine without any modification. At different loads the Pine oil, CPME and CPMEP blends were used in direct injection naturally aspirated compression ignition engine. The outcomes exhibited that at full load conditions for CPME and CPMEP blends increased brake specific fuel consumption, and decreased brake thermal efficiency, CO, HC emissions. NOx emissions decreased and smoke emissions are increased on CPME and CPMEP blends, expect B25 blend compared with diesel. The combustion analysis like the heat release rate, peak cylinder pressure, cumulative heat release rate and ignition delay for CPME, CPMEP blends slightly lower and combustion duration higher than diesel and pine oil. At the Same engine operating condition, the engine fuelled with pine oil the values of brake thermal efficiency 4.79%, peak cylinder pressure, heat release rate, cumulative heat release rate and ignition delay are increased. Brake specific fuel consumption, CO, HC, and smoke were 9.46%, 16.66%, 14.89% and 8.33% decreased. However, the NOx emission is 8.29% higher than that of diesel. Experimental fuels up to B50 (50% pine oil and 50% CPME) blends have proved good potential for future energy is needed.     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

Environmental effect of CI engine using microalgae methyl ester with doped nano additives

Algae are organisms that grow in marine environments and use carbon dioxide and light to create bio-mass. There are two groupings of algae: microalgae and macroalgae. Macroalgae are the large, multi-cellular algae often seen growing in ponds. Microalgae, on the other hand, are tiny, unicellular algae that normally grow in suspension within a body of water. Algae oil from microalgae has the possible to become a sustainable fuel source as biodiesel. Microalgae are produced through photosynthesis by utilizing sunlight, water, carbon dioxide and other nutrients. The Botryococcus braunii algal oil was extracted by mechanical extraction method. The transesterification reaction of Botryococcus braunii algal oil with methanol and base catalyst was used for the production of biodiesel. The samples B20 were prepared for each methyl ester obtained from Botryococcus braunii algal oil separately and then the doping of TiO₂ and SiO₂ nanoparticles were added to the each B20 blend samples at a dosage of 50 ppm and 100 ppm with an aid of ultrasonicator. Moreover, in the absence of any engine modifications, the performance and emission characteristics of those blend samples have been investigated from the experimentally measured values such as density, viscosity, calorific value, etc. while the engine performance was also analyzed through the parameters like BSFC, BTH, exhaust emission of CO, HC, NOx and CO₂. The experimental results reveal that the use of biodiesel blend with nano additives in diesel engine has exhibited good improvement in performance characteristic and reduction in exhaust emissions.     

Performance and emission characteristics of a spark ignition engine fuelled with butanol isomer-gasoline blends

The heavy reliance on petroleum-derived fuels such as gasoline in the transportation sector is one of the major causes of environmental pollution. For this reason, there is a critical need to develop cleaner alternative fuels. Butanol is an alcohol with four different isomers that can be blended with gasoline to produce cleaner alternative fuels because of their favourable physicochemical properties compared to ethanol. This study examined the effect of butanol isomer-gasoline blends on the performance and emission characteristics of a spark ignition engine. The butanol isomers; n-butanol, sec-butanol, tert-butanol and isobutanol are mixed with pure gasoline at a volume fraction of 20 vol%, and the physicochemical properties of these blends are measured. Tests are conducted on a SI engine at full throttle condition within an engine speed range of 1000–5000 rpm. The results show that there is a significant increase in the engine torque, brake power, brake specific fuel consumption and CO₂ emissions with respect to those for pure gasoline. The butanol isomers-gasoline blends give slightly higher brake thermal efficiency and exhaust gas temperature than pure gasoline at higher engine speeds. The iBu20 blend (20 vol% of isobutanol in gasoline) gives the highest engine torque, brake power and brake thermal efficiency among all of the blends tested in this study. The isobutanol and n-butanol blend results in the lowest CO and HC emissions, respectively. In addition, all of the butanol isomer-gasoline blends yield lower NO emissions except for the isobutanol-gasoline blend.     

Estimation of nitrogen oxides emissions from petrol and diesel passenger cars by means of on-board monitoring: Effect of vehicle speed,vehicle technology,engine type on emission rates

NO_X emission rates of 13 petrol and 3 diesel passenger cars as a function of average speed from 10 to 120 km/h, emission class (pre-Euro 1 – Euro 5), engine type were investigated by on-board monitoring on roads and highways of St. Petersburg using a portative Testo XXL 300 gas analyzer. The highest level of NO_X emission 0.5–2.5 g/km was inherent to old pre-Euro 1 petrol cars without a catalytic converter. NO_X emissions rates of Euro 1 and Euro 2 petrol cars changed within 0.15–0.9 g/km, Euro 3 – 0.015–0.27 g/km, Euro 4 – 0.013–0.1 g/km, Euro 5 – 0.002–0.043 g/km. Euro 3 – Euro 4 petrol cars generally satisfied corresponding NO_X Emission Standards (ES), except cold-start period, Euro 5 petrol cars did not exceed ES. Warmed, stabilized engines of Euro 3 – Euro 5 petrol cars showed 5–10 times lower NO_X emission rates than corresponding ES in the range of speed from 20 to 90 km/h. NO_X emission rates of diesel Euro 3 and Euro 4 cars varied from 0.45 to 1.1 g/km and from 0.31 to 1.1 g/km, respectively. Two examined diesel Euro 3 and one Euro 4 passenger vehicles did not satisfy NO_X ES at real use. Euro 3 diesel cars showed 28.9 times higher NO_X emissions than Euro 3 petrol cars and Euro 4 diesel car demonstrated 17.6 times higher NO_X emissions than Euro 4 petrol cars at warmed and stabilized engine at a cruise speed ranging from 30 to 60 km/h.     

Technical and environmental effects of biodiesel use in local public transport

Biodiesel use in local public transport could be especially significant in improving air quality in cities. The purpose of the experiments described in this paper was to evaluate the various (10, 20 and 50%) blends of biodiesel with diesel in the context of the engine and pollution aspects. As regards the experimental use of these findings on municipal buses, these experiments were the first reference in Hungary. The ages (15–20 years) and types of buses (Ikarus-280, Ikarus-260) used in the experiments are still common vehicles in Hungarian public transport. During our measurements, there was a significant difference between the change in fuel consumption of articulated and solo buses in traffic when compared to test bench measurements. The proportion of the engine performance reduction is nearly the same as that for biodiesel share in the blends. Most pollutants were decreasing (both at idle and full rpm), but this reduction is not directly proportional to the increase of the blending percentage. However, as for CO₂, emission increase was observed in the case of idle rpm in comparison to normal diesel operation, even though this phenomenon was not due to biodiesel use, but the catalytic converter and the fact that biodiesel was used for the first time in the engine concerned.     

Development of optimum friction new nano hybrid composite liner for biodiesel fuel engine

This work presents the preparation of aluminum (Al) 6061 nano hybrid composite samples reinforced with equal weight percentage of nano-ZrO₂, micro-SiC, micro-Gr particles of 0%, 0.75%, 1.5%, 2.25%, and 3% using stir casting method. Friction characteristics of the composite samples under reciprocating conditions were studied at 125 °C using L₂₇ orthogonal array and Taguchi method. The results of analysis of variance showed the influencing parameter for friction coefficient in the order of applied load and reciprocating sliding speed, followed by sliding distance and percent reinforcement. Hence, the total combined reinforcement sample of 6.75% was found to be optimum in terms of frictional characteristics and tensile strength. It was selected to synthesize lightweight nano hybrid composite cylinder liner (NL) and to replace the present cast iron cylinder liner (CL) used in biodiesel engine application. The developed NL had a 43.75% reduced weight than the currently used CL. Neat diesel and biodiesel from Jatropha oil and its diesel blends were used as test fuels. Experimental results proved that NL improved brake thermal efficiency, in-cylinder pressure, heat release rate and reduced carbon monoxide, hydrocarbon, and smoke emission in comparison with the existing liner. The results also showed that emission of the oxides of nitrogen (NO_x) increased marginally with the new liner. Thus, the newly developed NL was found suitable for both diesel- and biodiesel-operated internal combustion engines.     

Integrated vehicle and powertrain optimization for passenger vehicles with vehicle-infrastructure communication

This research proposes an optimal controller to improve fuel efficiency for a vehicle equipped with automatic transmission traveling on rolling terrain without the presence of a close preceding vehicle. Vehicle acceleration and transmission gear position are optimized simultaneously to achieve a better fuel efficiency. This research leverages the emerging Connected Vehicle technology and utilizes present and future information—such as real-time dynamic speed limit, vehicle speed, location and road topography—as optimization input. The optimal control is obtained using the Relaxed Pontryagin’s Minimum Principle. The benefit of the proposed optimal controller is significant compared to the regular cruise control and other eco-drive systems. It varies with the hill length, grade, and the number of available gear positions. It ranges from an increased fuel saving of 18–28% for vehicles with four-speed transmission and 25–45% for vehicles with six-speed transmission. The computational time for the optimization is 1.0–2.1 s for the four-speed vehicle and 1.8–3.9 s for the six-speed vehicle, given a 50 s optimization time horizon and 0.1 s time step. The proposed controller can potentially be used in real-time.     

Vehicle attribute trade-offs to meet the 2025 CAFE fuel economy target

The literature analyzes changes in vehicle attributes that can improve fuel economy to meet Corporate Average Fuel Economy (CAFE) standards. However, these analyses exclude either vehicle price, size, acceleration or technology advancement. A more comprehensive examination of the trade-offs among these attributes is needed, this case study focuses on technically feasible modifications to a reference 2012 vehicle to meet the 2025 fuel economy target. Scenarios developed to examine uncertainty in technology advancement indicate that expected technology cost reductions over time will be insufficient to offset the costs of additional fuel efficiency technologies that could be used to meet the 2025 fuel economy target while maintaining other vehicle attributes. The mid-price scenario results show the targeted 66% increase in fuel economy from 2012 to 2025 can be achieved with (i) a 10% ($2070) vehicle price increase (lightweight hybrid electric vehicle), (ii) a 31% (2.9 second) increase in the 0–97 km/h (60 mph) acceleration time (smaller engine), or (iii) a 17% (700 L) decrease in interior volume (smaller body) while maintaining other vehicle attributes. These results are consistent with those obtained using methods that generalize the US light-duty vehicle fleet, but are not a forecast of future vehicle attributes because combinations of less perceptible changes to vehicle price, acceleration and size would also be feasible. This study shows there are numerous ways that 2025 fuel economy targets can be met; therefore, the trade-offs quantified provide important insights on the implications of future CAFE standards.     

General statistics of diesel engines’ idle time: Shunting locomotives in industrial sidings in Poland 2009…2013

Shunting locomotive/switcher (AmE)/utilization profiles are analyzed in this paper, in particular on the basis of idle time data collected in nineteen Polish industrial sidings and yards. 40 years old, diesel-electric locomotives are observed during 1000 h. Idle times related to work cycles are analyzed statistically. The percentage of the shunting locomotive daily operating time that the engine is operating at idle amounts to 70% (from 55% to 90%), and average daily idle fuels consumption amounts to 150 l a day (from 90 to 240 l a day).Many European and Asian countries still operate a significant number of similar (ChME3, e.g. S200) old, diesel-electric locomotives (almost 8000 locomotives have been produced), for moving trains over long distances and as shunting locomotives.Observed frequent short idle time periods suggest necessity of widening future scope of idling times’ analysis. Adaptation of Polish rolling stock will be possible using prior general public education about dangerous carcinogens in diesel exhaust smoke and fuel waste related to diesel engines’ idling. Simple simultaneous depiction of diesel engine power time series together with idle time could be used for educational visualization of idling among a wider audience. In the future classical aggregated idle time statistics should be supplemented by models that are more related to the variability of shunting locomotives diesel generator’s power time series, e.g. distribution of frequent short individual idle time cases.     

Fuel economy of hybrid-electric versus conventional gasoline vehicles in real-world conditions: A case study of cold cities in Quebec,Canada

This paper investigates the fuel efficiency of commercial hybrid electric vehicles (HEVs) and compares their performance with respect to standard gasoline vehicles in the context of cold Canadian urban environments. The effect of different factors on fuel efficiency is studied including road driving conditions (link type, city size), temperature, speed, cold-starts and eco-driving training. For this study, fuel consumption data at the link level in real-world conditions was used from a sample of 74 instrumented vehicles. From the study fleet, 21 vehicles were HEVs. Among other results, the beneficial fuel efficiency merits of hybrid vehicles were demonstrated with respect to gasoline cars, in particular at low speeds and in urban (city) environments. After controlling for other factors, sedan HEVs were 28% more efficient than sedan gasoline vehicles. However, the low temperatures (below 0 °C) observed regularly during winter season in the study cities were identified as a detrimental factor to fuel economy. In winter, the fuel efficiency of HEVs decrease about 20% with respect to summer. Other factors such as eco-driving training, city size, cold start and vehicle type were also found to be statistically significant.     

A new offline optimization approach for designing a fuel cell hybrid bus

In this study a hydrogen powered fuel cell hybrid bus is optimized in terms of the powertrain components and in terms of the energy management strategy. Firstly the vehicle is optimized aiming to minimize the cost of its powertrain components, in an official driving cycle. The optimization variables in powertrain component design are different models and sizes of fuel cells, of electric motors and controllers, and batteries. After the component design, an energy management strategy (EMS) optimization is performed in the official driving cycle and in two real measured driving cycles, aiming to minimize the fuel consumption. The EMS optimization is based on the control of the battery’s state-of-charge. The real driving cycles are representative of bus driving in urban routes within Lisbon and Oporto Portuguese cities. A real-coded genetic algorithm is developed to perform the optimization, and linked with the vehicle simulation software ADVISOR. The trade-off between cost increase and fuel consumption reduction is discussed in the lifetime of the designed bus and compared to a conventional diesel bus. Although the cost of the optimized hybrid powertrain (62,230 €) achieves 9 times the cost of a conventional diesel bus, the improved efficiency of such powertrain achieved 36% and 34% of lower energy consumption for the real driving cycles, OportoDC and LisbonDC, which can originate savings of around 0.43 €/km and 0.37 €/km respectively. The optimization methodology presented in this work, aside being an offline method, demonstrated great improvements in performance and energy consumption in real driving cycles, and can be a great advantage in the design of a hybrid vehicle.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Evaluation of eco-driving training for vehicle fuel use and emission reduction: A case study in Australia

This study evaluates effectiveness of driver education teaching greater fuel efficiency (Eco-Driving) in a real world setting in Australia. The driving behaviour, measured in fuel use (litres per 100 km of travel) of a sample of 1056 private drivers was monitored over seven months. 853 drivers received education in eco-driving techniques and 203 were monitored as a control group. A simple experimental design was applied comparing the pre and post training fuel use of the treated sample compared to a control sample. This study found the driver education led to a statistically significant reduction in fuel use of 4.6% or 0.51 litres per 100 km compared to the control group.     

Sulphur abatement globally in maritime shipping

In 2016, the International Maritime Organization (IMO) decided on global regulations to reduce sulphur emissions to air from maritime shipping starting 2020. The regulation implies that ships can continue to use residual fuels with a high sulphur content, such as heavy fuel oil (HFO), if they employ scrubbers to desulphurise the exhaust gases. Alternatively, they can use fuels with less than 0.5% sulphur, such as desulphurised HFO, distillates (diesel) or liquefied natural gas (LNG). The options of lighter fuels and desulphurisation entail costs, including higher energy consumption at refineries, and the present study identifies and compares compliance options as a function of ship type and operational patterns.The results indicate distillates as an attractive option for smaller vessels, while scrubbers will be an attractive option for larger vessels. For all vessels, apart from the largest fuel consumers, residual fuels desulphurised to less than 0.5% sulphur are also a competing abatement option. Moreover, we analyse the interaction between global SO_X reductions and CO₂ (and fuel consumption), and the results indicate that the higher fuel cost for distillates will motivate shippers to lower speeds, which will offset the increased CO₂ emissions at the refineries. Scrubbers, in contrast, will raise speeds and CO₂ emissions.     

Regional climate impact of aerosols emitted by transportation modes and potential effects of policies on demand and emissions

The transportation system is one of the main sectors with significant climate impact. In the U.S. it is the second main emitter of carbon dioxide. Its impact in terms of emission of carbon dioxide is well recognized. But a number of aerosol species have a non-negligible impact. The radiative forcing due to these species needs to be quantified. A radiative transfer code is used. Remote sensing data is retrieved to characterize different regions. The radiative forcing efficiency for black carbon are 396 ± 200 W/m²/AOD for the ground mode and 531 ± 190 W/m²/AOD for the air transportation, under clear sky conditions. The radiative forcing due to contrail is 0.14 ± 0.06 W/m² per percent coverage. Based on the forcing from the different species emitted by each mode of transportation, policies may be envisioned. These policies may affect demand and emissions of different modes of transportation. Demand and fleet models are used to quantify these interdependencies. Depending on the fuel price of each mode, mode shifts and overall demand reduction occur, and more fuel efficient vehicles are introduced in the fleet at a faster rate. With the introduction of more fuel efficient vehicles, the effect of fuel price on demand is attenuated. An increase in fuel price of 50 cents per gallon, scaled based on the radiative forcing of each mode, results in up to 5% reduction in emissions and 6% reduction in radiative forcing. With technologies, significant reduction in climate impact may be achieved.     

Characteristics of gaseous and particulate pollutants exhaust from logistics transportation vehicle on real-world conditions

On-road vehicle tests of three heavy duty diesel trucks were conducted by a portable emission measurement system (PEMS) in Chengdu, China. SEMTECH-ECOSTAR provided by Sensors Inc. was employed to detect gaseous emissions and MI2, an emissions measuring instrument powered by the Pegasor Particulate Sensor (PPS) was used to detect particulate emissions during the tests. The impacts of speed, acceleration and engine load on emissions were analyzed. The average nitrogen oxides (NOx) emission factors of the heavy duty diesel truck (HDDT), medium-duty diesel truck (MDDT), light duty diesel truck (LDDT) were 7.29, 5.29 and 5.53 g/km. The particulate emission factors were 0.60, 0.30 and 0.14 g/km respectively, higher than the similar reported in the previous studies. Both gaseous and particulate emission exhibit significant correlations with the change in vehicle speed, acceleration and power demand. The highest emission was generally in high VSPs and higher loads. High engine load caused by aggressive driving was the main factor of high emissions for the vehicles on real-world conditions.     

Preferences for alternative fuel vehicles by Dutch local governments

Using a choice model, we estimate the preferences for alternative fuel vehicles by Dutch local governments. The analysis shows that local governments are willing to pay between 25% and 50% extra for an alternative fuel vehicle without a serious loss of utility. Further, local emissions are an important criterion on which to base a decision, especially for municipalities and provinces. We also calculate the utility for a number of prominent alternative fuel vehicles. We find that show that local governments value the battery electric vehicle and biogas internal combustion engine equally. It is important, however, that the time to refuel for electric vehicles is reduced to about 30 min.     

An assessment of gasoline motorcycle emissions performance and understanding their contribution to Tehran air pollution

Motorcycles are the third most common means of transportation in the megacity of Tehran. Hence, measurements of emission factors are essential for Tehran motorcycle fleets. In this study, 60 carburetor motorcycles of various mileages and engine displacement volumes were tested in a chassis dynamometer laboratory according to cold start Euro-3 emissions certification test procedures. For almost all of the tested samples, the average carbon monoxide (CO) emission factors were about seven times higher than the limits for Euro-3 certification. No motorcycle fell within the Euro-3 certification limit on CO emissions. 125 cc engine displacement volume motorcycles, which are dominant in Tehran, have the most total unburned hydrocarbons and CO emission rates, and they have less nitrous oxides (NO_X) emission rates and fuel consumption compared to those of larger engine volume motorcycles. Calculation of fuel-based emission factors and moles of combustion products shows that about 40% of fuel consumed by 125 cc engine volume motorcycles burns to incomplete combustion products. This proportion is lower for larger engine volume motorcycles. Approximation of relative air–fuel ratio results shows very rich combustion in selected motorcycles. Using a carburetor fuel supply system, low engine compression ratio, aging, and no catalyst could be reasons for high emission rates. These reasons could possibly result in high ultrafine particles emission rates from motorcycles. Comparison of total motorcycle pollutant emissions to that of passenger cars from previous studies in Tehran shows that motorcycles contribute to pollutant much higher than their contribution to the total fleet or total travels.     

Fuel price elasticities for single-unit truck operations in the United States

This paper provides fuel price elasticity estimates for single-unit truck activity, where single-unit trucks are defined as vehicles on a single frame with either (1) at least two axles and six tires; or (2) a gross vehicle weight greater than 10,000 lb. Using data from 1980 to 2012, this paper applies first-difference and error correction models and finds that single-unit truck activity is sensitive to certain macroeconomic and infrastructure factors (gross domestic product, lane miles expansion, and housing construction), but is not sensitive to diesel fuel prices. These results suggest that fuel price elasticities of single unit truck activity are inelastic. These results may be used by policymakers in considering policies that have a direct impact on fuel prices, or policies whose effects may be equivalent to fuel price adjustments.