Numerical simulation of the anti-shock performance of a gear case

Both sea battles and testing of ship in underwater explosions reveal unacceptably poor anti-shock performance of important shipboard equipment. Anti-shock performance of shipboard equipment is a significant factor determining fighting strength and survivability. The anti-shock performance of a shipboard gear case based on BV043/85 was investigated using numerical simulation. A geometric model of the gear case was built using MDT software and meshed in HyperMesh software, and then the finite element model of the gear case was formed. Using ABAQUS software, the anti-shock performance of the gear case was simulated. First, shock response of typical regions of gear case was determined. Next, some generalizations were made about the anti-shock performance of the gear case by analyzing the Mises stress of typical regions varied with shock inputs. Third, weak regions were determined from simulation results. The threshold values of shock resistance of the gear case at different impulse widths were obtained through interpolating the numerical simulation results selected from the most dangerous spot. This research provides a basis for further optimization of the design of gear cases.     

Analysis of ultimate uniaxial compressive strength of stiffened panel considering influence of shear load北大核心CSCD

［Objective］This study aims to explore the law of the critical compression stress of stiffened panels under the influence of in-plane shear load, and whether in-plane shear load combined with lateral pressure will introduce a strong coupling effect. ［Method ］ To this end, nonlinear finite element (FE) software ABAQUS is used to perform numerical simulation analysis under combined loads on a group of FE models. A limit state equation/curve is then derived from the dimensionless calculation results based on the minimum square error method. ［Results］The results show that the influence law of in-plane shear load on the critical compression stress of stiffened panels is clarified, and a limit state equation of stiffened panels that considers the effect of shear load is obtained. ［Conclusion］The limit state equation in this paper can provide references for modifying the ultimate strength of stiffened panels under the influence of in-plane shear load. © 2023 Chinese Journal of Ship Research. All rights reserved.     

FEA for designing of floating raft shock-resistant system

Choosing the equipment with good shock-resistant performance and taking shock protection measures while designing the onboard settings, the safety of onboard settings can be assured when warships, especially submarine subjected to non-contact underwater explosion, that is, these means can be used to limit the rattlespace (i. e. , the maximum displacement of the equipment relative to the base) and the peak acceleration experienced by the equipment. Using shock-resistant equipments is one of shock protection means. The shock-resistant performance of the shock-resistant equipments should be verified in the design phase of the equipments. The FEA (finite element analysis) software, for example, MSC. NASTRANw, can be used to verify the shock-resistant performance. MSC. PATRAN and MSC. NASTRAN are used for modeling and analyzing the floating raft vibration isolating equipment. The model of the floating raft and the floating raft vibration isolating system are theoretically analyzed and calculated, and the analysis results are in agreement with the test results. The transient response analysis of the system model follows the modal analysis of the floating raft vibration isolating system. And it is used to verify the shock-resistant performance. The analysis and calculation method used in this paper can be used to analyze the shock-resistant performance of onboard shock-resistant equipments.     

Fluid-structure coupled analysis of underwater cylindrical shells

Underwater cylindrical shell structures have been found a wide of application in many engineering fields, such as the element of marine, oil platforms, etc. The coupled vibration analysis is a hot issue for these underwater structures. The vibration characteristics of underwater structures are influenced not only by hydrodynamic pressure but also by hydrostatic pressure corresponding to different water depths. In this study, an acoustic finite element method was used to evaluate the underwater structures. Taken the hydrostatic pressure into account in terms of initial stress stiffness, an acoustical fluid-structure coupled analysis of underwater cylindrical shells has been made to study the effect of hydrodynamic pressures on natural frequency and sound radiation. By comparing with the frequencies obtained by the acoustic finite element method and by the added mass method based on the Bessel function, the validity of present analysis was checked. Finally, test samples of the sound radiation of stiffened cylindrical shells were acquired by a harmonic acoustic analysis. The results showed that hydrostatic pressure plays an important role in determining a large submerged body motion, and the characteristics of sound radiation change with water depth. Furthermore, the analysis methods and the results are of significant reference value for studies of other complicated submarine structures.     

Influence of external restraint distribution on welding buckling of thin plate butt joint北大核心CSCD

［Objectives］It is easy to produce buckling distortion when welding thin plate butt joints, which affects the construction period, cost and performance, but this can be controlled by applying external restraints. ［Methods ］ First, a butt welding test of a thin plate under external restraints is carried out, and the out-of-plane deformation is measured by the optical surface scanning method. At the same time, finite element (FE) models in a free state and external restraint state are established, and the thermal mechanical phenomena of the two models are subjected to thermal-elastic-plastic FE analysis (TEP FE). The influence of different external restraint distributions on the welding buckling distortion of the joints is then studied, and reasons for controlling welding buckling distortion are analyzed from the perspective of longitudinal plastic strain and longitudinal contraction force.［Results ］ The out-of-plane deformation of the corresponding model is in good agreement with the measured results, and milder than the out-of-plane deformation of the model in a free state. When external restraints are applied, the longitudinal plastic strain of the weld and its adjacent metal decreases, and the longitudinal contraction force of the thin plate also decreases.［Conclusions ］ The results verify that external restraints can effectively control welding buckling distortion, and the control effects are different depending on the external restraint distribution. © 2023 Chinese Journal of Ship Research. All rights reserved.     

Fuzzy sliding mode control method for vertical motion of autonomous underwater gliders北大核心CSCD

［Objective］This paper proposes a fuzzy sliding mode controller based on T-S fuzzy logic for the vertical plane motion control of an autonomous underwater glider (AUG) with limited actuator capability. ［Methods］In the fuzzy sliding mode controller, the fuzzy switching rate is used to replace the switching rate in the fixed time controller to effectively suppress buffeting. The fuzzy switching rate is obtained by fitting the switching rate of the fixed time controller with T-S fuzzy rules. Based on the limited capabilities of AUG actuators, a saturation auxiliary system is designed to improve the actuator saturation effect. Finally, the performance of the system is verified by Lyapunov stability analysis and numerical simulation. ［Results］The results show that the AUG under the fuzzy sliding mode controller and the saturation auxiliary system can converge in finite time. The effectiveness of the fuzzy sliding mode controller and the saturation auxiliary system are verified by numerical simulation. ［Conclusions］By making comparisons with the fixed-time controller, it is verified that the two controllers have similar control performance, and the buffeting of the fuzzy sliding mode controller is lesser. © 2022 Journal of Clinical Hepatology. All rights reserved.     

Three-dimensional fluid-structure interaction case study on cubical fluid cavity with flexible bottom

In this paper, we report our study on a numerical fluid-structure interaction problem originally presented by Mok et al.(2001) in two dimensions and later studied in three dimensions by Valdés Vazquez(2007), Lombardi(2012), and Trimarchi(2012). We focus on a 3D test case in which we evaluated the sensitivity of several input parameters on the fluid and structural results. In particular, this analysis provides a starting point from which we can look deeper into specific aspects of these simulations and analyze more realistic cases, e.g., in sails design. In this study, using the commercial software ADINATM, we addressed a well-known unsteadiness problem comprising a square box representing the fluid domain with a flexible bottom modeled with structural shell elements. We compared data from previously published work whose authors used the same numerical approach, i.e., a partitioned approach coupling a finite volume solver(for the fluid domain) and a finite element solver(for the solid domain). Specifically, we established several benchmarks and made comparisons with respect to fluid and solid meshes, structural element types, and structural damping, as well as solution algorithms. Moreover, we compared our method with a monolithic finite element solution method. Our comparisons of new and old results provide an outline of best practices for such simulations.     

水下爆炸空化效应作用下全船响应的并行计算(英文)

As well as shock wave and bubble pulse loading, cavitation also has very significant influences on the dynamic response of surface ships and other near-surface marine structures to underwater explosive loadings. In this paper, the acoustic-structure coupling method embedded in ABAQUS is adopted to do numerical analysis of underwater explosion considering cavitation. Both the shape of bulk cavitation region and local cavitation region are obtained, and they are in good agreement with analytical results. The duration of reloading is several times longer than that of a shock wave. In the end, both the single computation and parallel computation of the cavitation effect on the dynamic responses of a full-scale ship are presented, which proved that reloading caused by cavitation is non-ignorable. All these results are helpful in understanding underwater explosion cavitation effects.     

基于塑性模型的钢悬链立管疲劳分析（英文）

The most critical issue in the steel catenary riser design is to evaluate the fatigue damage in the touchdown zone accurately. Appropriate modeling of the riser-soil resistance in the touchdown zone can lead to significant cost reduction by optimizing design. This paper presents a plasticity model that can be applied to numerically simulate riser-soil interaction and evaluate dynamic responses and the fatigue damage of a steel catenary riser in the touchdown zone. Utilizing the model, numerous riser-soil elements are attached to the steel catenary riser finite elements, in which each simulates local foundation restraint along the riser touchdown zone. The riser-soil interaction plasticity model accounts for the behavior within an allowable combined loading surface. The model will be represented in this paper, allowing simple numerical implementation. More importantly, it can be incorporated within the structural analysis of a steel catenary riser with the finite element method. The applicability of the model is interpreted theoretically and the results are shown through application to an offshore 8.625″ steel catenary riser example. The fatigue analysis results of the liner elastic riser-soil model are also shown. According to the comparison results of the two models, the fatigue life analysis results of the plasticity framework are reasonable and the horizontal effects of the riser-soil interaction can be included.     

Analysis on acoustic performance of floating raft vibration isolation system with liquid tank北大核心CSCD

［Objective］This paper aims to establish a dynamic model of a floating raft vibration isolation system with a liquid tank in order to study the mass effect of the liquid medium, tank form, structural stiffness and loading rate on acoustic performance. ［Methods］A floating raft system with a cuboidal or cylindrical liquid tank is taken as the research object, and a fluid-structure coupling finite element dynamic model is established. The dynamic force transmission rate and power flow are then used to evaluate the acoustic performance of the system. The influence of the mass effect of the liquid medium, tank form, structural stiffness and loading rate of tank volume on the acoustic performance of the floating raft system are analyzed.［Results］The results show similar laws obtained through the calculation and analysis of the floating raft system with two types of tanks. The structural stiffness of the tank affects the mass effect of the liquid medium in the tank to a certain extent. ［Conclusions］If full advantage is to be taken of the liquid mass effect in the tank with a large loading rate to improve the acoustic performance of the floating raft system, the design of the liquid tank and raft structure must have sufficient stiffness. In addition, under the condition that the floating raft structure has sufficient stiffness, its acoustic performance will improve significantly as the tank loading rate increases in the relevant low frequency range. © 2022 Journal of Clinical Hepatology. All rights reserved.     

Numerical analysis of impact resistance of honeycomb structures with different Poisson's ratios北大核心CSCD

［Objectives］This papers aims to analyze the impact resistance of honeycomb structure with different Poisson's ratio. ［Methods］Based on the explicit dynamic finite element method, this paper analyzes the dynamic mechanical properties of honeycomb structures with different Poisson's ratios under in-plane impact load, and explores the influence laws of Poisson's ratios on their impact resistance. Three typical honeycomb structures with negative/zero/positive Poisson's ratios (reentrant hexagon, hexagon and semi-reentrant hexagon) are selected, their geometric parameters are changed to give them the same relative density and different Poisson's ratios (−2.76 – +3.63), and their dynamic mechanical properties under low/medium/high-speed dynamic displacement loads are analyzed. ［Results ］ The results show that the zero Poisson's ratio semi-reentrant honeycomb structure has the best structural stability without transverse deformation under compression deformation; without structural instability, the platform stress has little correlation with the Poisson's ratio; and the compact strain and total energy absorbtion increases with the absolute value of the Poisson's ratio. Negative Poisson's ratio honeycomb structures with large t/l and small θ are suitable for applications with high platform stress (strong deformation resistance), and negative Poisson's ratio honeycomb structures with small t/l and small θ are suitable for high total energy absorbtion applications, while zero Poisson's ratio semi-reentrant honeycomb structures are suitable for applications with high platform stress (strong deformation resistance). ［Conclusions］This study can provide references for the type selection and geometric parameter design of side impact honeycomb structures. © 2023 Authors. All rights reserved.     

Numerical evaluation method of lightning rod protection probability北大核心CSCD

［Objectives］Aiming at the current situation in which it is difficult to efficiently evaluate protection probability through traditional lightning rod evaluation methods, an efficient numerical evaluation algorithm is developed on the basis of an electrogeometric model (EGM) and attractive volume to realize the efficient calculation of lightning protection probability at any point in space.［Methods］This method first determines the attractive volume boundary of the lightning rod and protection object according to the interception process of the upward and downward leaders. The collection surface and exposure arc of the lightning stroke distance are then calculated, enabling the attractive risk and interception effect of the lightning rod to be quantified. Finally, the attraction and interception characteristics of the lightning rod are integrated to establish a numerical evaluation model of protection probability. To verify the accuracy of this method, the general rule of lightning rod protection probability is analyzed and the results compared with the existing analysis method.［Result］The evaluation results of this method show good agreement with those of classical leader progression model (LPM) theory.［Conclusions］ The method proposed herein has a high degree of quantification and can realize the efficient calculation of lightning protection probability at any point in space, which can provide useful references for lightning protection design work. © 2023 Authors. All rights reserved.     

有限元法在非线性波浪与结构物相互作用中的应用(英文)

We review recent advances in the finite element method (FEM) simulations of interactions between waves and structures. Our focus is on the potential theory with the fully nonlinear or second-order boundary condition. The present paper has six sections. A review of previous work on interactions between waves and ocean structures is presented in Section one. Section two gives the mathematical formulation. In Section three, the finite element discretization, mesh generation and the finite element linear system solution methods are described. Section four presents numerical methods including time marching schemes, computation of velocity, remeshing and smoothing techniques and numerical radiation conditions. The application of the FEM to the wave-structure interactions are presented in Section five followed by the concluding remarks in Section six.     

非结构化有限体积法研究薄板的冲击动力学问题(英文)

The examination of an unstructured finite volume method for structural dynamics is assessed for simulations of systematic impact dynamics. A robust display dual-time stepping method is utilized to obtain time accurate solutions. The study of impact dynamics is a complex problem that should consider strength models and state equations to describe the mechanical behavior of materials. The current method has several features. 1) Discrete equations of unstructured finite volume method naturally follow the conservation law. 2) Display dual-time stepping method is suitable for the analysis of impact dynamic problems of time accurate solutions. 3) The method did not produce grid distortion when large deformation appeared. The method is validated by the problem of impact dynamics of an elastic plate with initial conditions and material properties. The results validate the finite element numerical data.     

基于流固耦合方法的两自由度水翼流激振动特性研究（英文）

The flutter of a hydrofoil can cause structural damage and failure, which is a dangerous situation that must be avoided. In this work, based on computational fluid dynamics and structural finite element methods, a co-simulation framework for the flow-induced vibration of hydrofoil was established to realize fluid-structure interaction. Numerical simulation research was conducted on the flow-induced vibration characteristics of rigid hydrofoil with 2-DOF under uniform flow, and the heave and pitc...     

Dynamic plastic response of clamped stiffened plates with large deflection

Study on the dynamic response, and especially the nonlinear dynamic response of stiffened plates is complicated by their discontinuity and inhomogeneity. The finite element method （FEM） and the finite strip method are usually adopted in their analysis. Although many useful conclusions have been obtained, the computational cost is enormous. Based on some assumptions, the dynamic plastic response of clamped stiffened plates with large deflections was theoretically investigated herein by a singly symmetric beam model. Firstly, the deflection conditions that a plastic string must satisfy were obtained by the linearized moment-axial force interaction curve for singly symmetric cross sections and the associated plastic flow rule. Secondly, the possible motion mechanisms of the beam under different load intensity were analysed in detail. For structures with plastic deformations, a simplified method was then given that the arbitrary impact load can be replaced equivalently by a rectangular pulse. Finally, to confirm the validity of the proposed method, the dynamic plastic response of a one-way stiffened plate with four fully clamped edges was calculated. The theoretical results were in good agreement with those of FEM. It indicates that the present calculation model is easy and feasible, and the equivalent substitution of load almost has no influence on the final deflection.     

Parameter optimization and parametric deviation influence for shock resistance of double-stage vibration isolation system with limiters北大核心CSCD

［Objectives］For marine nuclear power plants, the relative displacement of the pump supported by a vibration isolation system should be strictly restricted. In order to improve the shock resistance of a vibration isolation system with displacement limiters, the parameter optimization and parametric deviation influence are studied. ［Methods］The theoretical model of a double-stage vibration isolation system with typical limiter parameters is established, the analysis of the shock response characteristics of the system is carried out using the direct integration method, the optimal limiter parameters are obtained using a genetic algorithm, and the influence of parameter deviation on the shock resistance of the system is studied. ［Results］Limiter parameters significantly affect the shock response characteristics of the vibration isolation system. The optimal limiter parameters improve the shock resistance of the system, but parameter deviation has a great influence on shock resistance. Based on the influence of parameter deviation, a deviation control strategy is proposed in which the elastic parameter should have a positive deviation and the gap parameter a negative deviation. The simulation results show that the proposed strategy can effectively alleviate the shock resistance degradation caused by deviation.［Conclusions］The results of this study can be used to guide the design, manufacturing and variation control of limiters for vibration isolation systems. © 2022 Journal of Clinical Hepatology. All rights reserved.     

Design of underwater robot lines based on a hybrid automatic optimization strategy

In this paper, a hybrid automatic optimization strategy is proposed for the design of underwater robot lines. Isight is introduced as an integration platform. The construction of this platform is based on the user programming and several commercial software including UG6.0, GAMBIT2.4.6 and FLUENT12.0. An intelligent parameter optimization method, the particle swarm optimization, is incorporated into the platform. To verify the strategy proposed, a simulation is conducted on the underwater robot model 5470, which originates from the DTRC SUBOFF project. With the automatic optimization platform, the minimal resistance is taken as the optimization goal;the wet surface area as the constraint condition; the length of the fore-body, maximum body radius and after-body＇s minimum radius as the design variables. With the CFD calculation, the RANS equations and the standard turbulence model are used for direct numerical simulation. By analyses of the simulation results, it is concluded that the platform is of high efficiency and feasibility. Through the platform, a variety of schemes for the design of the lines are generated and the optimal solution is achieved. The combination of the intelligent optimization algorithm and the numerical simulation ensures a global optimal solution and improves the efficiency of the searching solutions.     

Numerical method of electromagnetic pulse response of conductor with complex load北大核心CSCD

[Objectives]Electromagnetic pulse can seriously affect and even destroy naval shipborne electronic information systems, weapons, equipment and so on. Due to the complexity of the antenna port load circuit, it is necessary to formulate a numerical method which can easily obtain the antenna load current. [Methods]The induced current of the terminal is obtained on the basis of the finite-difference time-domain (FDTD) and Holland model. According to the Thévenin equivalent circuit, the conductor is equivalent to the voltage source to realize decoupling between the conductor and load end, and the load circuit is solved using Simulink software.[Results]Compared with the traditional terminal model, this method is simple and feasible for high-order circuit processing. The effectiveness of the model is verified using non-linear elements and parallel capacitors and resistors as the load respectively. The results show that the calculation results of this method are consistent with those of the traditional methods. Finally, the antenna of the end-connected protect- or is calculated. The results show that the lead inductance caused by the installation of the protector is an important factor affecting the protection performance.[Conclusions]The method proposed in this paper can greatly reduce the simulation complexity of the coupling current of an antenna with a complex load, giving it useful reference value for the field of ship electromagnetic pulse protection design. © 2023 Editorial Department of Chinese Journal of Ship Research. All Rights Reserved.