船首外伸对规则波顶浪航行上水量的影响分析（英文）

This paper presents the results of an experimental investigation dealing with the effect of bow overhang extensions on the quantity of shipping water over the foredeck in case of ships advancing in regular head waves. To perform this investigation, a series of free-running tests was conducted in regular waves using an experimental model of a multipurpose cargo ship to quantify the amount of shipping water. The tests were performed on five bow overhang variants with several combinations of wavelength and ship speed conditions. It was observed that the quantity of shipping water was affected by some parameters such as wavelength, ship speed, and bow shape in terms of an overhang extension. The results show the significant influence of an overhang extension, which is associated with the bow flare shape, on the occurrence of water shipping. These results involve the combined incoming regular waves and model speed.     

Optimization of bow shape for a non ballast water ship

In this research,a commercial CFD code ＂Fluent＂ was applied to optimization of bulbous bow shape for a non ballast water ships（NBS）.The ship was developed at the Laboratory of the authors in Osaka Prefecture University,Japan.At first,accuracy of the CFD code was validated by comparing the CFD results with experimental results at towing tank of Osaka Prefecture University.In the optimizing process,the resistances acting on ships in calm water and in regular head waves were defined as the object function.Following features of bulbous bow shapes were considered as design parameters： volume of bulbous bow,height of its volume center,angle of bow bottom,and length of bulbous bow.When referring to the computed results given by the CFD like resistance,pressure and wave pattern made by ships in calm water and in waves,an optimal bow shape for ships was discovered by comparing the results in the series of bow shapes.In the computation on waves,the ship is in fully captured condition because shorter waves,λ/Lpp 0.6,are assumed.     

Validation of 6-DOF motion simulations for ship turning in regular waves

In this study, a six degrees of freedom (6-DOF) motion simulation method of a ship steering in regular waves is validated. The proposed simulation model is based on the two-time scale concept where the 6-DOF motions are expressed as the sum of the low-frequency maneuvering motions and high-frequency wave-induced motions. Turning simulations of a KCS container ship model with a rudder angle of \(\pm 35^\circ\) in calm water and regular waves are performed and the obtained results are compared with the results of a free-running model test. The model tests were conducted using a ship model of length 3.057 m in a square tank at the National Research Institute of Fisheries Engineering, Japan. The wave conditions were as follows: the wave height was 3.6 m at full-scale, ratio of wavelength to ship length was 1.0, and the ship approached in the head wave direction before it was steered. The present method can simulate both the turning motion and wave-induced motions in regular waves with practical accuracy.

     

Added resistance acting on hull of a non ballast water ship

In this paper, added resistances acting on a hull of non ballast water ship(NBS) in high waves is discussed. The non ballast water ships were developed at the laboratory of the authors at Osaka Prefecture University, Japan. In the present paper, the performances of three kinds of bow shapes developed for the NBS were theoretically and experimentally investigated to find the best one in high waves. In previous papers, an optimum bow shape for the NBS was developed in calm water and in moderated waves. For a 2 m model for experiments and computations, the wave height is 0.02 m. This means that the wave height is 15% of the draft of the ship in full load conditions. In this paper, added resistances in high waves up to 0.07 m for a 2 m model or 53% of the full load draft are investigated. In such high waves linear wave theories which have been used in the design stage of a ship for a long time may not work well anymore, and experiments are the only effective tool to predict the added resistance in high waves. With the computations for waves, the ship is in a fully captured condition because shorter waves, λ/Lpp0.6, are assumed.     

Experimental study of drillship resistance performance in open and closed state of moonpool北大核心CSCD

[Objective] This paper carries out an experimental study of a multi-function dirllship model with moonpool structure in towing tank, aiming at analyzing the effects of the moonpool structure on the ship resistance in open and closure condition.[Methods]Taking a dirllship as the research object, the ship motion response in regular and irregular waves is investigated. The resistance of the ship in hydrostatic water and waves is measured with tension sensors, and the acceleration characteristics of the bow, midship and stern are analyzed by acceleration sensors.[Results]The results indicate that hull resistance under light load conditions is greater when open moonpool, while hydrostatic water resistance with closed moonpool is greater under design load conditions. The closed moonpool in regular waves reduces stern acceleration by 58.2%, bow resistance by 46.7% and heave response by 41.8%. The peak of resistance at the bow in irregular waves is about ten times higher than that at the stern, and the peak of resistance occurs more often when the moonpool is open at the same time.[Conclusions]The experimental study shows that the difference in load conditions changes the waterplane area and affects the hull resistance in hyrostatic water. In contrast, the closure of the moonpool not only reduces acceleration and resistance, but also improves surge and heave. As such, this paper can provide references for the structural design of drillships with moonpools. © 2023 Journal of Nanjing Agricultural University. All rights reserved.     

水翼辅助推进船舶波浪中运动和增阻特性研究

基于在船首两侧增添（固定）水翼的水翼辅助推进船舶的设想,选取集装箱船型作为研究对象,采用三维面元法对原型和水翼船在规则波中的运动和增阻响应进行了预报,并与试验结果进行比较,验证了计算结果的准确性。研究结果表明水翼能够有效地减小船舶在波浪中的纵摇、垂荡和增阻响应,其中添加水翼船在波浪中的纵摇和垂荡响应峰值分别减少了21%和24%,而增阻响应则减小了80%。此外还对水翼展弦比和安装位置对船舶在波浪中的运动和增阻响应的影响进行了研究。     

Estimation and prediction of effective inflow velocity to propeller in waves

A free running test using a container ship model clarified properties of effective inflow velocity to propellers in waves. The analysis assumes that thrust and torque vary keeping their relation to the effective inflow velocity as represented by open-water characteristics of a propeller in a steady calm water condition. Measurement in regular waves confirmed the variation of average values of the effective wake coefficient and ship speed depending on wavelength and wave encounter angle. Comparison with the longitudinal flow velocity measured at the sides of the propeller using an onboard vane-wheel current meters confirmed that one can estimate the effective inflow velocity based on thrust or torque data. Theoretical estimates in regular waves based on a strip method are provided and compared with the experimental data. A prediction model of the future inflow velocity is proposed to cope with a time delay of a propeller pitch controller for higher propeller efficiency in waves.     

船体表面海洋污损生物附着规律分析

阐述了海洋污损生物的在船体表面的附着过程,分析了海水温度、盐度、水体流速、海水透明度以及附着基材料性质对污损生物附着情况的影响状况,基于实船调查,探讨了船舶水线区、船艏、船舯、船艉、船底、螺旋桨、舵等7大浸水部位污损情况的差异,获得船体表面海洋污损生物附着的初步规律,认为船体表面污损生物的附着种类和数量与船舶的类型、航线、营运性质等都有关系,船底是船舶污损最为严重的部位,船艏的附着量比船舯和船艉要小,螺旋桨和舵的污损不是很严重,附着的主要是粘附力极强的底栖生物,藻类是水带线附近的优势附着种。此结论可为研制高效、环保的防污手段提供参考依据。     

Numerical and experimental analysis of bow flare slamming on a Ro–Ro vessel in regular oblique waves

A method for the prediction of slamming loads on ship hulls is presented and validated for a 20-knot, 120-m car carrier. A nonlinear strip theory is used to calculate the relative motions of ship and wave. The relative vertical and roll velocities for a slamming event are given as input to the slamming calculation program, which is based on a generalized two-dimensional Wagner formulation and solved by the boundary element method. The method is fast and robust. Model tests of a car carrier have been carried out in regular head, bow, and bow quartering waves of various heights. Slamming on two panels in the upper part of the bow flare has been studied. It has been found that the water pile-up around the bow due to the forward speed of the vessel significantly increases the slamming pressures. A simplified way of including this effect is presented. When the calculated slamming pressures are corrected for 3D effects, they compare well with the measured data. Since the effect of the wave elevation due to the forward speed and the effect of three-dimensional flow act in opposite directions, excluding both of them produced results that also agreed quite well with the experiments, especially for the most severe slamming events.     

Three-dimensional numerical analysis of shipping water onto a moving ship using a particle method

The objective of this study was to develop a numerical analysis method based on the moving particle semi-implicit method for simulating shipping water on a moving ship. Towing tests of a very large crude carrier were numerically analyzed for three typical wavelengths. The ship was forced to move in order to express previously measured ship oscillations, and the calculated fluid behavior and the impact pressure on the deck were compared with the experimental results.     

Computational and experimental study on local ship loads in short and steep waves

Currently, little information exists on the validity of interface-capturing methods in predicting local ship wave loads in short and steep waves. This study compares computational and experimental results in such a case (kA = 0.24, L _wave /L _ship = 0.16). The results allow the variation of wave loading between ten locations in the bow area of the ship to be observed. The computations were performed with an unstructured RANS solver that models free-surface flows with a volume-of-fluid method. In the model tests, the wave loads were measured with pressure sensors. The analysis of the results focuses on the wave conditions and on the pressure histories of the local wave loads. The computational and experimental results are in good qualitative agreement and encourage the further use of the computational results.     

SBD技术在"探索一号"科考船线型设计中的应用

文章介绍了"探索一号"科考船船体改型设计及基于数值仿真方法(Simulation Based Design,SBD)的艏部线型优化设计。首先,依据总体设计要求,对原船艏部进行了加长并开展了线型设计,采用基于RANS的数值评估方法对改型前后船舶阻力进行计算分析。在此基础上,采用SBD技术开展了艏部线型优化设计,以设计航速时的总阻力作为目标函数,FFD方法实现船体几何自动重构,利用粒子群优化算法对线型优化设计问题进行求解,设计结果表明:在满足工程约束条件下,最优方案总阻力收益十分显著,航速12kns时模型总阻力减小了7.7%,剩余阻力系数减小了26.6%。     

规则波浪中舰船操纵与横摇耦合运动模拟及特性分析

采用六自由度舰船操纵性方程与横摇波浪力矩耦合构成动力学模型,对舰船在规则波浪中的操纵与横摇耦合运动特性进行了模拟研究.其中操纵性方程采用MMG模型,波浪力矩由切片法计算,舰船航向按PD控制.模拟计算了某船正横规则波浪下保持航向的横摇运动,计算结果与单自由度理论结果进行了比较,其幅频曲线与相频曲线两者符合较好,间接证明了耦合构成动力学模型的有效性.在此基础上计算了不同浪向角和航速下的横摇运动,以横摇等值极坐标曲线表征舰船规则波浪中的横摇特性,从而给出了规则波浪下舰船耦合动力学所描述的运动特征.     

迎浪规则波中波浪增阻和船体垂向运动的数值预报(英文)

The numerical prediction of added resistance and vertical ship motions of one ITTC (International Towing Tank Conference) S-175 containership in regular head waves by our own in-house unsteady RANS solver naoe-FOAM-SL JTU is presented in this paper. The development of the solver naoe-FOAM-SJTU is based on the open source CFD tool, OpenFOAM. Numerical analysis is focused on the added resistance and vertical ship motions (heave and pitch motions) with four very different wavelengths (0.8Lpp≤λ≤1.5Lpp) in regular head waves. Once the wavelength is near the length of the ship model, the responses of the resistance and ship motions become strongly influenced by nonlinear factors, as a result difficulties within simulations occur. In the paper, a comparison of the experimental results and the nonlinear strip theory was reviewed and based on the findings, the RANS simulations by the solver naoe-FOAM-SJTU were considered competent with the prediction of added resistance and vertical ship motions in a wide range of wave lengths.     

Wave responses of a coastal cargo ship consisting of unit modules

This article discusses the dynamic responses of a coastal cargo ship that consists of unit modules with advance forward speed in waves. We introduce a simple way of connecting the modules that has enough capability to link the modular parts of the ship as a unified whole. The flexible connection consists of male and female rubber fenders with additional pretensioned ropes. This kind of connection system is proposed for use in coastal regions with relatively calm waters wherein the modular ship can move at a moderate speed. The modules are assumed to be rigid compared to the connections. Computations were performed to investigate the vertical elastic responses of four modules connected end-to-end with the assumption that in the simple hinge, no gaps occur in the flexible rubber connections between adjacent modules. A simple method, which is an extension of the computational analysis we reported previously, is presented to study the hydroelasticity and rope tension forces of the modular ship with forward speed in waves. Experiments with a three-dimensional model at Froude numbers of 0 and 0.16 in head waves were performed to evaluate the effectiveness of the calculation method. In the experiments, deflections for each part were measured using calibrated potentiometers. Force transducers were used to measure the rope tension force between the modules of the articulated cargo ship. Some slight differences were observed, but generally the calculated results showed the same trends as the experimental values.     

基于船波相对运动的船艏砰击仿真方法

在分析船波相对运动表达式的基础上计算船艏典型剖面的船波相对运动,探讨船艏入水过程中的砰击问题,对比船体某剖面3种入水仿真模型计算所得的砰击载荷,讨论三维外形和航行速度对船艏剖面砰击外载荷的影响。在该分析中,船体在规则波浪中的运动用基于三维势流理论的水动力软件AQWA计算获得,船波相对运动通过理论推导计算获得,用对船艏结构施加强迫运动的方式模拟船波相对运动的真实过程。采用An—sys／Ls—Dyna软件的流固耦合分析进行入水仿真,流体划分为ALE体积网格,船艏视为刚体,划分为Lagrange有限元网格。对比结果表明：在三维模型中,相邻剖面引起剖面最大压力点处的液面变化对该点的砰击压力有增大效果,航速有增大剖面砰击压力的作用,减小船艏底部纵向斜升角有利于降低砰击压力。     

基于模型试验与三维水弹性理论的船舶波激振动响应研究

船体波激振动使得船体结构中产生高频、持续和具有一定幅值的振动应力,可能引起结构发生严重的疲劳损伤,因而对船舶结构的安全性带来严峻的挑战。文章以一艘大型LNG船为研究对象,采用三维线性水弹性理论与水池模型试验方法对船舶波激振动响应进行了比较分析,研究了规则波与不规则波中的波激振动特性。改变该LNG船的刚度,并保持船型、重量分布等其它主船体特征不变,在模型试验和理论计算中探讨了刚度对波激振动的影响。通过两种刚度船体梁的模型试验与理论计算结果的比较分析,给出了波浪周期和船体刚度的变化对波激振动影响的几点结论。     

数值波浪水池及顶浪中船舶水动力计算

基于粘流理论建立了三维数值波浪水池,模拟了非线性波浪,并对规则波顶浪中前进的拘束船模的水动力进行了计算.数值模拟中,控制方程-RANS方程和连续性方程使用有限体积法离散,非线性自由面采用VOF方法处理;在入口边界模拟柔性造波板运动产生入射波,使用位于波浪水池尾部的人工阻尼区消波.给出了非线性规则波的模拟结果以及规则波顶浪中前进的拘束船模的水动力计算结果,并与理论解及DUT(Delfi University of Technology)的试验数据进行了比较,二者吻合良好.     

人工气泡船水动力性能试验研究

文章通过试验途径研究了人工大气泡船的水动力性能,试验包括气泡船流量测试试验、气泡船通气对比试验、气泡船与其原型船静水及波浪中对比试验。结果表明,气泡船充气后阻力能大大下降;对于气泡船有一最经济的充气流量;气泡船在静水及波浪中的综合性能均优于常规船型,特别是阻力下降很多。根据试验结果还分析了气泡降阻的原理:具有一定压力的气泡腔,除了减小船底的摩擦阻力之外,还支撑了艇的一部分重量,减小了艇体的吃水,从而阻力也相应地减少。     

运输船舶在波浪中失速的近似估算

如何准确、快速、简便地估算船舶在波浪中的失速,已成为船舶研究、设计人员及航运界有关人员共同关心的一个重要课题。文中给出了近似估算运输船舶在波浪中失速的2个方法。对处于初步设计阶段且尚未做过静水快速性能模型试验的运输船舶,可直接应用第2个方法。该方法提出的近似估算公式应用方便,也不用编程便可直接人工计算,且与模型试验结果相当吻合。