Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.     

An aircraft performance model implementation for the estimation of global and regional commercial aviation fuel burn and emissions

Estimates of global aviation fuel burn and emissions are currently nearly 10 years out of date. Here, the development of the Aircraft Performance Model Implementation (APMI) software which is used to update global commercial aviation fuel burn and emissions estimates is described. The results from APMI are compared with published estimates obtained using the US Federal Aviation Administration’s System for Assessing Aviation’s Global Emissions (SAGE) for the year 2006. The number of global departures modelled with the APMI software is 8% lower compared with SAGE and reflects the difference between their commercial air traffic statistics data sources. The mission fuel burn, CO₂ and H₂O estimates from APMI are approximately 20% lower than those predicted by SAGE for 2006 while the estimate for the total global aircraft SO_x emissions is approximately 40% lower. The estimates for the emissions of CO, HC and NO_x are 10%, 140% and 30% higher than those predicted by SAGE respectively. The reasons for these differences are discussed in detail.     

Exhaust emissions generated under actual operating conditions from a hybrid vehicle and an electric one fitted with a range extender

The paper describes exhaust emission tests performed on a PHEV (Plug-in Hybrid Electric Vehicle) and a BEV (Battery Electric Vehicle), in which the combustion engine was used as a range extender. The measurements of the exhaust emissions were performed for CO₂/fuel consumption, CO, THC and NO_x. The RDE measurements were performed including the engine operating parameters and emissions analysis. This analysis shows that the engines of BEVs and PHEVs operate in a different parameter range when under actual operating conditions, which directly translates into the exhaust emission values. This is particularly the case for the emission of NO_x. The investigations were carried out for two routes differentiated by the length and share of the urban and extra-urban cycles. For both routes, the emission of THC and CO were lower for the PHEV engine – HC by 69% (22 mg/km, route 1) and 6% (15 mg/km, route 2), CO by 69% (0.12 mg/km, route 1) and 80% (0.1 mg/km, route 2). For route 1, characterized by a greater share of the urban cycle, the emission of NO_x was lower by 70% (2 mg/km) for the BEV engine, and (route 2) lower by 60% (8 mg/km) for the PHEV engine. Additionally, the curves of the exhaust emissions in time for individual exhaust components have been presented that indicate that in the motorway cycle the emission of THC and CO from the BEV vehicle increases significantly up to ten times compared to urban cycle.     

Effects of the 80 km/h and variable speed limits on air pollution in the metropolitan area of barcelona

In 2008 the regional government of Catalonia (Spain) reduced the maximum speed limit on several stretches of congested urban motorway in the Barcelona metropolitan area to 80 km/h, while in 2009 it introduced a variable speed system on other stretches of its metropolitan motorways. We use the differences-in-differences method, which enables a policy impact to be measured under specific conditions, to assess the impact of these policies on emissions of NO_x and PM₁₀. Empirical estimation indicate that reducing the speed limit to 80 km/h causes a 1.7–3.2% increase in NO_x and 5.3–5.9% in PM₁₀. By contrast, the variable speed policy reduced NO_x and PM₁₀ pollution by 7.7–17.1% and 14.5–17.3%. As such, a variable speed policy appears to be a more effective environmental policy than reducing the speed limit to a maximum of 80 km/h.     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

Estimation of nitrogen oxides emissions from petrol and diesel passenger cars by means of on-board monitoring: Effect of vehicle speed,vehicle technology,engine type on emission rates

NO_X emission rates of 13 petrol and 3 diesel passenger cars as a function of average speed from 10 to 120 km/h, emission class (pre-Euro 1 – Euro 5), engine type were investigated by on-board monitoring on roads and highways of St. Petersburg using a portative Testo XXL 300 gas analyzer. The highest level of NO_X emission 0.5–2.5 g/km was inherent to old pre-Euro 1 petrol cars without a catalytic converter. NO_X emissions rates of Euro 1 and Euro 2 petrol cars changed within 0.15–0.9 g/km, Euro 3 – 0.015–0.27 g/km, Euro 4 – 0.013–0.1 g/km, Euro 5 – 0.002–0.043 g/km. Euro 3 – Euro 4 petrol cars generally satisfied corresponding NO_X Emission Standards (ES), except cold-start period, Euro 5 petrol cars did not exceed ES. Warmed, stabilized engines of Euro 3 – Euro 5 petrol cars showed 5–10 times lower NO_X emission rates than corresponding ES in the range of speed from 20 to 90 km/h. NO_X emission rates of diesel Euro 3 and Euro 4 cars varied from 0.45 to 1.1 g/km and from 0.31 to 1.1 g/km, respectively. Two examined diesel Euro 3 and one Euro 4 passenger vehicles did not satisfy NO_X ES at real use. Euro 3 diesel cars showed 28.9 times higher NO_X emissions than Euro 3 petrol cars and Euro 4 diesel car demonstrated 17.6 times higher NO_X emissions than Euro 4 petrol cars at warmed and stabilized engine at a cruise speed ranging from 30 to 60 km/h.     

Evaluating the social cost of cruise ships air emissions in major ports of Greece

Detailed NO_x, SO₂ and PM_2.5 emissions have been estimated for cruise ships in the five busiest Greek ports (i.e. Piraeus, Santorini, Mykonos, Corfu and Katakolo) for year 2013. The emissions were analyzed in terms of gas species, seasonality and activity. The total in-port inventory of cruise shipping accounted to 2742.7 tons: with NO_x being dominant (1887.5 tons), followed by SO₂ and PM_2.5 (760.9 and 94.3 tons respectively). Emissions during hotelling corresponded to 88.5% of total and have significantly outweighed those produced during ships’ maneuvering activities (11.5% of total). Seasonality was found to play a major role, as summer emissions and associated impacts were significantly augmented. The anticipated health impacts of ship emissions can reach to €24.3 million or to €5.3 per passenger proving the necessity of control of the emissions produced by cruise ships in port cities or policy and measures towards a more efficient cruise industry.     

Performance and emission characteristics of a spark ignition engine fuelled with butanol isomer-gasoline blends

The heavy reliance on petroleum-derived fuels such as gasoline in the transportation sector is one of the major causes of environmental pollution. For this reason, there is a critical need to develop cleaner alternative fuels. Butanol is an alcohol with four different isomers that can be blended with gasoline to produce cleaner alternative fuels because of their favourable physicochemical properties compared to ethanol. This study examined the effect of butanol isomer-gasoline blends on the performance and emission characteristics of a spark ignition engine. The butanol isomers; n-butanol, sec-butanol, tert-butanol and isobutanol are mixed with pure gasoline at a volume fraction of 20 vol%, and the physicochemical properties of these blends are measured. Tests are conducted on a SI engine at full throttle condition within an engine speed range of 1000–5000 rpm. The results show that there is a significant increase in the engine torque, brake power, brake specific fuel consumption and CO₂ emissions with respect to those for pure gasoline. The butanol isomers-gasoline blends give slightly higher brake thermal efficiency and exhaust gas temperature than pure gasoline at higher engine speeds. The iBu20 blend (20 vol% of isobutanol in gasoline) gives the highest engine torque, brake power and brake thermal efficiency among all of the blends tested in this study. The isobutanol and n-butanol blend results in the lowest CO and HC emissions, respectively. In addition, all of the butanol isomer-gasoline blends yield lower NO emissions except for the isobutanol-gasoline blend.     

A velocity and payload dependent emission model for heavy-duty road freight transportation

The paper develops a forecasting model of emissions from traffic flows embracing the dynamics of driving behavior due to variations in payload. To measure of emissions at the level of individual vehicles under varying payloads a portable emission measurement system is used. This paper reports on a model based on data at the level of individual vehicles for a representative road trajectory. The model aggregates the data to the level of a homogeneous flow dependent of velocity and specific power, which is dependent on payload weight. We find a lean specification for the model that provides emission factors for CO₂, NO_x, HC, CO, and NO₂. The results indicate that, in comparison with earlier models, NO_x emissions in particular tend to be underestimated.     

System for assessing Aviation’s Global Emissions (SAGE), Part 1: Model description and inventory results

In early 2001, the US Federal Aviation Administration embarked on a multi-year effort to develop a new computer model, the System for assessing Aviation’s Global Emissions (SAGE). Currently at Version 1.5, the basic use of the model has centered on the development of yearly global inventories of commercial aircraft fuel burn and emissions of various pollutants to serve as the basis for scenario modeling. This paper describes the algorithms and data used in the model as well as the results from initial validation assessments. SAGE results indicate that global fuel burn and nitrogen oxide (NO_x) emissions decreased by over 6% from 2000 to 2001 (fuel burn and NO_x), and then steadily increased to over 12% (fuel burn) and 15.5% (NO_x) above 2000 levels in 2005. Comparisons to the results from previous studies have shown that SAGE tends to agree more closely with fuel burn and NO_x than with CO and HC. Validation assessments have shown that SAGE can predict per flight fuel burn to within 3% on an average basis with no apparent bias, when compared to about 60,000 flight’s worth of data from a major US airline and about 20,000 flight’s worth of data from two major Japanese airlines.     

The effects of small roundabouts on emissions and fuel consumption: a case study

The effects of small roundabouts on emissions and fuel consumption were evaluated using the “car-following” method in a before/after study. The results showed that at a roundabout replacing a signalised junction, CO emissions decreased by 29%, NO_x emissions by 21% and fuel consumption by 28%. At roundabouts, replacing yield regulated junctions, CO emissions increased on average by 4%, NO_x emissions by 6% and fuel consumption by 3%. The results indicate that the large reductions in emissions and fuel consumption at one rebuilt signalised junction can “compensate for” the increase produced by several yield-regulated junctions rebuilt as roundabouts.     

Are HOV/eco-lanes a sustainable option to reducing emissions in a medium-sized European city?

Innovative traffic management measures are needed to reduce transportation-related emissions. While in Europe, road lane management has focused mainly on introduction of bus lanes, the conversion to High Occupancy Vehicles (HOV) and eco-lanes (lanes dedicated to vehicles running on alternative fuels) has not been studied comprehensively. The objectives of this research are to: (1) Develop an integrated microscopic modeling platform calibrated with real world data to assess both traffic and emissions impacts of future Traffic Management Strategies (TMS) in an urban area; (2) Evaluate the introduction of HOV/eco-lanes in three different types of roads, freeway, arterial and urban routes, in an European medium-sized city and its effects in terms of emissions and traffic performance. The methodology consists of three distinct phases: (a) Traffic and road inventory data collection; (b) Traffic and emissions simulation using an integrated platform of microscopic simulation; and (c) Evaluation of scenarios. For the baseline scenario, the statistical analysis shows valid results. The results show that HOV and eco-lanes in a medium European city are feasible, and when the Average Occupancy of Vehicles (AOV) increases, on freeways, the majority of vehicles can reduce their travel time (2%) with a positive impact in terms of total emissions (−38% NO_x, −39% HC, −43% CO and −37% CO₂). On urban and arterial corridors, the reduction in emissions could be achieved only if the AOV increases from 1.50 to 1.70 passengers/vehicle. Total emissions of the corridor with an AOV of 1.70 passengers/vehicle can be reduced up to 35–36% for the urban route while the values can be reduced by 36–39% for the arterial road. With the introduction of Hybrid Electric Vehicles (HEV) and Electric Vehicles (EV) it is possible to reduce emissions, although the introduction of eco-lanes did not show significant reductions in emissions. When both policies are simulated together, an emissions improvement is observed for the arterial route and for two of the scenarios.     

Effects of battery chemistry and performance on the life cycle greenhouse gas intensity of electric mobility

Lithium traction batteries are a key enabling technology for plug-in electric vehicles (PEVs). Traction battery manufacture contributes to vehicle production emissions, and battery performance can have significant effects on life cycle greenhouse gas (GHG) emissions for PEVs. To assess emissions from PEVs, a life cycle perspective that accounts for vehicle production and operation is needed. However, the contribution of batteries to life cycle emissions hinge on a number of factors that are largely absent from previous analyses, notably the interaction of battery chemistry alternatives and the number of electric vehicle kilometers of travel (e-VKT) delivered by a battery. We compare life cycle GHG emissions from lithium-based traction batteries for vehicles using a probabilistic approach based on 24 hypothetical vehicles modeled on the current US market. We simulate life-cycle emissions for five commercial lithium chemistries. Examining these chemistries leads to estimates of emissions from battery production of 194–494 kg CO₂ equivalent (CO₂e) per kWh of battery capacity. Combined battery production and fuel cycle emissions intensity for plug-in hybrid electric vehicles is 226–386 g CO₂e/e-VKT, and for all-electric vehicles 148–254 g CO₂e/e-VKT. This compares to emissions for vehicle operation alone of 140–244 g CO₂e/e-VKT for grid-charged electric vehicles. Emissions estimates are highly dependent on the emissions intensity of the operating grid, but other upstream factors including material production emissions, and operating conditions including battery cycle life and climate, also affect life cycle GHG performance. Overall, we find battery production is 5–15% of vehicle operation GHG emissions on an e-VKT basis.     

Environmental effect of CI engine using microalgae methyl ester with doped nano additives

Algae are organisms that grow in marine environments and use carbon dioxide and light to create bio-mass. There are two groupings of algae: microalgae and macroalgae. Macroalgae are the large, multi-cellular algae often seen growing in ponds. Microalgae, on the other hand, are tiny, unicellular algae that normally grow in suspension within a body of water. Algae oil from microalgae has the possible to become a sustainable fuel source as biodiesel. Microalgae are produced through photosynthesis by utilizing sunlight, water, carbon dioxide and other nutrients. The Botryococcus braunii algal oil was extracted by mechanical extraction method. The transesterification reaction of Botryococcus braunii algal oil with methanol and base catalyst was used for the production of biodiesel. The samples B20 were prepared for each methyl ester obtained from Botryococcus braunii algal oil separately and then the doping of TiO₂ and SiO₂ nanoparticles were added to the each B20 blend samples at a dosage of 50 ppm and 100 ppm with an aid of ultrasonicator. Moreover, in the absence of any engine modifications, the performance and emission characteristics of those blend samples have been investigated from the experimentally measured values such as density, viscosity, calorific value, etc. while the engine performance was also analyzed through the parameters like BSFC, BTH, exhaust emission of CO, HC, NOx and CO₂. The experimental results reveal that the use of biodiesel blend with nano additives in diesel engine has exhibited good improvement in performance characteristic and reduction in exhaust emissions.     

Development of a corrected average speed model for calculating carbon dioxide emissions per link unit on urban roads

The purpose of our study is to develop a “corrected average emission model,” i.e., an improved average speed model that accurately calculates CO₂ emissions on the road. When emissions from the central roads of a city are calculated, the existing average speed model only reflects the driving behavior of a vehicle that accelerates and decelerates due to signals and traffic. Therefore, we verified the accuracy of the average speed model, analyzed the causes of errors based on the instantaneous model utilizing second-by-second data from driving in a city center, and then developed a corrected model that can improve the accuracy. We collected GPS data from probe vehicles, and calculated and analyzed the average emissions and instantaneous emissions per link unit. Our results showed that the average speed model underestimated CO₂ emissions with an increase in acceleration and idle time for a speed range of 20 km/h and below, which is the speed range for traffic congestion. Based on these results, we analyzed the relationship between average emissions and instantaneous emissions according to the average speed per link unit, and we developed a model that performed better with an improved accuracy of calculated CO₂ emissions for 20 km/h and below.     

Carbon emission from urban passenger transportation in Beijing

Urban passenger transport significantly contributes to global greenhouse gas emissions, especially in developing countries owing to the rapid motorization, thus making it an important target for carbon reduction. This article established a method to estimate and analyze carbon emission from urban passenger transport including cars, rail transit, taxis and buses. The scope of research was defined based on car registration area, transport types and modes, the stages of rail transit energy consumption. The data availability and gathering were fully illustrated. A city level emission model for the aforementioned four modes of passenger transport was formulated, and parameters including emission factor of electricity and fuel efficiency were tailored according to local situations such as energy structure and field survey. The results reveal that the emission from Beijing’s urban passenger transport in 2012 stood at 15 million tonnes of CO₂, of which 75.5% was from cars, whereas car trip sharing constitutes only 42.5% of the total residential trips. Bus travel, yielding 28.6 g CO₂, is the most efficient mode of transport under the current situations in terms of per passenger kilometer (PKM) emission, whereas car or taxi trips emit more than 5 times that of bus trips. Although a decrease trend appears, Beijing still has potential for further carbon reduction in passenger transport field in contrast to other cities in developed countries. Development of rail transit and further limitation on cars could assist in reducing 4.39 million tonnes CO₂ emission.     

New car preferences move away from greater size,weight and power: Impact of Dutch consumer choices on average CO2-emissions

This paper assesses the separate effects of consumer preferences and technological advances on sales-weighted average CO₂ emissions of new passenger cars in the Netherlands. Since 2008, consumer preferences have been moving away from large size, weight and power whereby car buyers were offsetting more than 50% of the potential CO₂ reduction from technological advances. From 2008 to 2011 consumer choices not only ceased to offset a large share of the technological advances, but contributed more than an additional 30% to CO₂ reductions. Had consumer preferences not decoupled from the historical upward trend, the Dutch sales-weighted average CO₂ emissions of new passenger cars would have been 139 g/km rather than the 126 grams CO₂ per km in 2011.     

Potential of low viscosity oils to reduce CO2 emissions and fuel consumption of urban buses fleets

This paper shows the results of a comparative fleet test the main objective of which was to measure the influence of Low Viscosity Oils (LVO) over the fuel consumption and CO₂ emissions of urban buses. To perform this test, 39 urban buses, classified into candidate and reference groups depending on the engine oil viscosity, covered a 60,000 km mileage corresponding to two rounds of standard Oil Drain Interval (ODI). In the same way, for 9 buses of the 39 buses, the effect of differential LVO over fuel consumption and their interaction with engine LVO was assessed during the second ODI.Test results confirm that the use of LVO could reduce fuel consumption, hence CO₂ emissions. However, special attention should be taken prior to its implementation in a fleet, particularly if the vehicles are powered by engines with high mechanical and thermal stresses during vehicle operation because this could lead to friction loss increase, loss of the potential fuel consumption reduction of LVO and, in the worst scenario, higher rates of engine wear.     

Sulphur abatement globally in maritime shipping

In 2016, the International Maritime Organization (IMO) decided on global regulations to reduce sulphur emissions to air from maritime shipping starting 2020. The regulation implies that ships can continue to use residual fuels with a high sulphur content, such as heavy fuel oil (HFO), if they employ scrubbers to desulphurise the exhaust gases. Alternatively, they can use fuels with less than 0.5% sulphur, such as desulphurised HFO, distillates (diesel) or liquefied natural gas (LNG). The options of lighter fuels and desulphurisation entail costs, including higher energy consumption at refineries, and the present study identifies and compares compliance options as a function of ship type and operational patterns.The results indicate distillates as an attractive option for smaller vessels, while scrubbers will be an attractive option for larger vessels. For all vessels, apart from the largest fuel consumers, residual fuels desulphurised to less than 0.5% sulphur are also a competing abatement option. Moreover, we analyse the interaction between global SO_X reductions and CO₂ (and fuel consumption), and the results indicate that the higher fuel cost for distillates will motivate shippers to lower speeds, which will offset the increased CO₂ emissions at the refineries. Scrubbers, in contrast, will raise speeds and CO₂ emissions.