共查询到20条相似文献,搜索用时 35 毫秒
1.
2.
3.
《Vehicle System Dynamics: International Journal of Vehicle Mechanics and Mobility》2012,50(4):573-596
An existing driver–vehicle model with neuromuscular dynamics is improved in the areas of cognitive delay, intrinsic muscle dynamics and alpha–gamma co-activation. The model is used to investigate the influence of steering torque feedback and neuromuscular dynamics on the vehicle response to lateral force disturbances. When steering torque feedback is present, it is found that the longitudinal position of the lateral disturbance has a significant influence on whether the driver’s reflex response reinforces or attenuates the effect of the disturbance. The response to angle and torque overlay inputs to the steering system is also investigated. The presence of the steering torque feedback reduced the disturbing effect of torque overlay and angle overlay inputs. Reflex action reduced the disturbing effect of a torque overlay input, but increased the disturbing effect of an angle overlay input. Experiments on a driving simulator showed that measured handwheel angle response to an angle overlay input was consistent with the response predicted by the model with reflex action. However, there was significant intra- and inter-subject variability. The results highlight the significance of a driver’s neuromuscular dynamics in determining the vehicle response to disturbances. 相似文献
4.
SMA是沥青码蹄脂碎石(Stone Matrix Asphal)的缩写,是一种以沥青结合料与少量的纤维稳定剂、细集料,以及较多的填料(矿粉)组成的沥青玛蹄脂,填充于间断级配粗集料骨架间隙中组成一体所形成的沥青混合料,简称SMA。该文介绍了SMA在上海的应用及其施工技术。 相似文献
5.
预应力曲线箱梁和异形箱梁的研究 总被引:7,自引:0,他引:7
近年来 ,国内外学者对曲线箱梁和异形箱梁的静力分析理论和计算方法作过大量的研究 ,但这些理论和方法在某种程度上都存在着一定的局限性 ,特别是在实际设计工作中 ,运用起来不能得心应手。为此本文在综合前人已取得经验下 ,针对桥梁结构设计中分析曲线箱梁、异形箱梁 ,经常遇到的难题进行了研究 ,建立一个较为完善的理论和方法 ,编制了等参元空间分析程序。在实际工程中进行实桥试验 ,验证了本文理论和方法的正确性。本文的研究工作更准确描述了箱梁的荷载响应 ,为设计人员提供直观的设计依据。对曲线箱梁和异形箱梁受力特性有了更一步的理解 ,并提出了新的见解 相似文献
6.
利用AVL公司开发的BOOST软件可宏观地描述发动机的热力学过程且优化发动机的性能,而AVL的CRUISE软件可调用BOOST建立的发动机模型.在进行道路循环工况的仿真时,须对发动机全部工况点进行准确的标定.文中采用BOOST开发了发动机的仿真模型.通过调整节气门开度和燃烧模型参数,标定了发动机在多个转速和负荷点的转矩、功率和油耗,较好地模拟了发动机的动力性和经济性.最后基于ECE循环工况,将此模型与CRUISE进行联合仿真,分析了发动机瞬态工况的动力性、油耗和NO_x排放等参数. 相似文献
7.
混凝土的推广使用已有一个世纪,目前在现代工程建设中仍占有重要的地位。而在今天,混凝土的裂缝较为普遍,在桥梁工程中裂缝几乎无所不在,尽管我们在施工中采取各种各样的措施,但收效甚微,裂缝仍然时有出现。该文指出,究其原因,人们对混凝土温度变化所产生的应力注意不够是其中之一,尤其是大体积混凝土。对此,温度应力与温度控制具有重要的意义。 相似文献
8.
针对互通式立交出口可能出现的多种情况,结合工程实践,探讨其设计技术问题,提出设计思路及技术对策,并在技术分析中强调融入“安全至上”“动态设计”“灵活性设计”“宽容性设计”等设计新理念,使出口设计安全、合理. 相似文献
9.
J. R. Serrano F. J. Arnau V. Dolz A. Tiseira M. Lejeune N. Auffret 《International Journal of Automotive Technology》2008,9(3):277-288
This article presents a two-stage turbocharged heavy-duty diesel (HDD) engine designed to fulfil the US2007 anti-pollution
directive. This directive imposes very restrictive limits on the NOx and particle emissions of HDD engines. In this work,
the possibility of combining particle traps in the exhaust line to reduce soot emissions with very high EGR rates to reduce
NOx emissions is considered. This new generation engine implements two-stage turbocharging in order to improve the bsfc when
the engine is working on steady conditions as well as to optimize the engine transient response. After carrying out the tests,
the results were analyzed and the engine settings were adjusted to maximise its behaviour and minimise pollutant emissions.
NOx and soot emission peaks were also analyzed at engine transient conditions in order to keep them under certain levels,
and thus maintain the overall pollutant emissions to a level that is as low as possible. In summary, a double-stage turbocharging
configuration can greatly improve engine driveability (between 23% and 36% depending on engine speed), while reducing NOx
emissions during transient evolution without increasing opacity peaks beyond the stated limits. 相似文献
10.
水泥混凝土安全护栏 总被引:1,自引:0,他引:1
赵文光 《筑路机械与施工机械化》1994,11(2):9-14
通过水泥混凝土安全护栏在道路交通中的实际应用,对其结构形式和主要参数以及具体的施工方法进行了较为详实的叙述,并对比介绍了水泥混凝土安全护栏的使用效果。 相似文献
11.
介绍了三辊式和三螺杆式气门校正机的机械结构,分析了气门杆部、气门盘部偏歪校正的机理,讨论了机器结构、压辊形状、螺杆形状等对校正质量和效率的影响;对三螺杆式、三辊式、双螺杆式及搓板式气门校正机加以比较,阐述了它们各自的优缺点。 相似文献
12.
主要进述丰田雷克萨斯(凌志)ES300车防抱死制动系统(ABS)的结构,主要零件的检修,以及ABS轿故障灯常亮的故障诊断与排除。 相似文献
13.
14.
介绍CATIA软件的主要特点及应用CATIA软件进行客车底架设计的参数化建模和有限元强度分析的方法. 相似文献
15.
16.
目前我国的高速公路项目后评价 总被引:1,自引:0,他引:1
结合在北京、江苏、广西等地的调研经验,对现阶段高速公路项目后评价工作中存在的尖锐问题展开了细致剖析,并在此基础上提出自己的几点建议,以供相关部门借鉴参考。 相似文献
17.
18.
该文从研究超薄磨耗层的级配的选择入手,简单分析了超薄磨耗层的结构特点和强度形成机理,给出了几种国内外常用的超薄磨耗层级配范围,并提出了将SAC-10做为其研究的设计级配。在研究超薄磨耗层沥青混合料配合比设计的基础上,通过对SAC-10沥青混合料的马歇尔试验,确定了该沥青混合料的矿料级配和最佳沥青含量。最后采用车辙试验、浸水马歇尔和冻融劈裂试验及小梁弯曲试验等一系列试验,检测超薄磨耗层沥青混合料的各项路用性能,为在实际工程中的应用提供理论依据。 相似文献
19.
20.
公路工程监理人员市场供需模型研究 总被引:2,自引:0,他引:2
提出了建立监理人员需求和供给模型的方法,推导了计算公式。根据公路建设发展的历史数据,对历年公路建设监理人员需求和供给进行了计算和比较。 相似文献