点蚀损耗对船体梁极限强度的影响（英文）

The paper focuses on the assessment of the hull girder ultimate strength,combined with random pitting corrosion wastage,by the incremental-iterative method.After a brief review about the state of art,the local ultimate strength of pitted platings under uniaxial compression is preliminarily outlined and subsequently a closed-form design formula is endorsed in the Rule incremental-iterative method,to account for pitting corrosion wastage in the hull girder ultimate strength check.The ISSC bulk carrier is assumed as reference ship in a benchmark study,devoted to test the effectiveness of the incremental-iterative method,by a comparative analysis with a set of FE simulations,performed by Ansys Mechanical APDL.Four reference cases,with different locations of pitting corrosion wastage,are investigated focusing on nine combinations of pitting and corrosion intensity degrees.Finally,a comparative analysis between the hull girder ultimate strength,combined with pitting corrosion wastage,and the relevant values,complying with the Rule net scantling approach,is performed.Based on current results,the modified incremental-iterative method allows efficiently assessing the hull girder ultimate strength,combined with pitting corrosion wastage,so revealing useful both in the design process of new vessels and in the structural health monitoring of aged ships.     

Improved design formulas for the ultimate strength of platings with circular openings and manholes under uniaxial compression

The paper focuses on the ultimate strength of perforated platings with circular openings and manholes, eventually reinforced by ringed or carling stiffeners, in order to develop a comprehensive and rationale format, useful to assess the ultimate capacity of perforated plate panels under uniaxial compression. In this respect, a large number of FE simulations is performed by Ansys Mechanical APDL, in order to provide new design formulas for the ultimate strength of platings with circular openings or manholes and, subsequently, for perforated plate panels reinforced by local stiffeners. The design formulas are developed by properly varying the opening size and the scantlings of ringed or carling stiffeners, in order to provide a comprehensive set of design curves. Hence, the incidence of the opening longitudinal position on the ultimate capacity of perforated platings, without and with local stiffeners, is also investigated. Finally, the proposed equations are applied in a straightforward design example. Based on current results, the new design formulas allow a reliable assessment of the ultimate capacity of platings with circular openings or manholes and the incidence of local stiffeners on the plating ultimate strength, so providing a rationale design format that could be easily embodied in current Rules and guidelines.     

Experimental and numerical study of localized pitting effect on compressive behavior of tubular members

Locally pitted tubular members are usually considered as stub columns to assess the ultimate strength. However, it is not suitable for those with relatively larger slenderness ratios as their failure behavior is more complex and closely related to corrosion features of localized pitting. This paper presents compressive column tests on locally pitted tubular members of a moderate slenderness ratio. Corrosion pits were artificially introduced on local surface of the members, forming corrosion patches with various corrosion features. A numerical modelling method was proposed to reproduce the test specimens. Localized pitting damage was proven to cause substantial declines in the load deformation capacity and ultimate strength, and have a significant effect on the failure mode. The failure of a pitted member is mostly initiated by local buckling after yielding occurs in the corrosion patch, concurrent with pitting closure, and even shear cracking of member wall due to the perforated pits. Moreover, shape change of the corrosion patch most likely results in the failure mode to alter from column buckling to local buckling or interactive buckling. The shape ratio of the corrosion patch is one of the critical factor to influence the ultimate strength of locally pitted members. The proposed modelling method is applicable for extensive stochastic simulations so as to develop an empirical formula and to clarify the probabilistic characteristics of ultimate strength.     

Effect of pitting corrosion on the ultimate strength of steel plates subjected to in-plane compression and bending

Corrosion pits with a circular cone shape are typically observed on coated hold frames of aged bulk carriers which carry exclusively coal and iron ore. In order to ensure the safety of these types of bulk carrier, it is necessary to understand the effect of pitting corrosion on the local strength of hold frames. In order to investigate this effect, a series of nonlinear finite-element (FE) analyses has been performed with pitted plates subjected to in-plane compressive loads and bending moments. It has been shown that the ultimate compression load or bending moment of pitted plates is smaller than that of uniformly corroded plates in terms of average thickness loss, and that predictions of the ultimate strength using the average thickness loss at the minimum cross section would be conservative. In order to establish a method of evaluating strength reduction due to pitting corrosion, it is important to identify the failure mode that would be most detrimentally affected by pitting corrosion. It was found that the reduction of the ultimate compressive load or bending moment due to pitting corrosion is smaller than that of the tensile strength in terms of equivalent thickness.     

含点蚀损伤船体加筋板在纵向压力下的极限强度

针对老龄化船舶结构上的点状腐蚀,利用非线性有限元方法进行计算,分析304个船体加筋板的极限强度,探讨带板柔度、加强筋柔度、腐蚀面积比和腐蚀深度比对纵向压力下含点蚀损伤船体加筋板极限强度的影响,拟合出点状腐蚀下船体加筋板极限强度折减公式并对其适用性进行验证,研究结果具有一定的工程参考意义和价值。     

Buckling and ultimate capability of plates and stiffened panels in axial compression

This paper presents extensive non-linear finite element (FE) analysis and formulation development work carried out on the ultimate compressive strength of plates and stiffened panels of ship structures. A review of contemporary designs for large ships was carried out. The existing formulae for plate ultimate compressive strength were reviewed and compared with non-linear FE analysis results. A semi-analytical formula for ultimate compressive strength assessments of stiffened panels was proposed and is described. The developed formula was verified against results using ABAQUS non-linear FE software for a series of 61 stiffened panels and a good agreement between the proposed formula and FE results were achieved. The method was verified against a large number of published FE results and was also compared with 58 experimental results. The developed method was also applied to the deck and bottom structures for a range of various sizes oil tankers and bulk carriers.     

Compressive strength of tubular members with localized pitting damage considering variation of corrosion features

Localized pitting corrosion often occurs on marine and offshore structures in the form of patch corrosion with great uncertainties in the location, size and shape. The variation of corrosion features affects ultimate strength of tubular members significantly, but it is still not well understood. This paper presents a numerical study on tubular members of diverse slenderness ratios to clarify the localized pitting effect on ultimate strength. Numerical analyses were performed based on novel models of pitted members that were calibrated against benchmark column tests. Corrosion pits were randomly introduced on the local outside surfaces of members via stochastic simulation, forming corrosion patches varied in the location, size and shape. Numerical results obtained were regressed to propose a unified empirical formula to predict ultimate strength. It turned out that the shape of the corrosion patch has a significant influence on the ultimate strength. The shape change of the patch can alter failure modes of medium length columns. The reduction of ultimate strength is closely related to the shape ratio of the patch besides the volume loss of corroded material. The unified empirical formula incorporating the shape ratio and the volume loss shows a good ability to predict the experimental results.     

Effect of pitting corrosion on local strength of hold frames of bulk carriers (2nd Report)—Lateral-distortional buckling and local face buckling

Pitting corrosion is typical corrosion observed on coated hold frames of bulk carriers which exclusively carry coal and iron ore. In order to secure the safety of these types of bulk carriers, it is important to understand the effect of pitting corrosion on local strength of hold frames.

In order to investigate this effect, a series of 4- and 3-point bend tests on structural models which consist of web, shell and face plates has been carried out. Artificial pitting was created on the web plate to simulate pitting. In the 4-point bend tests, two equal concentrated loads have been applied vertically at the one-third points of simply supported models so that compression load due to bending would act on the face plate. In this testing condition, lateral-distortional buckling occurred before reaching the ultimate strength and local buckling of the face plate was observed after reaching the ultimate strength. The effect of web plate pitting on the lateral-distortional buckling strength was found to be small but the ultimate strength decreases with increase in the degree of pitting intensity. In the 3-point bend tests, concentrated load has been applied vertically at the center of simply supported models so that compression load due to bending would act on the face plate. In this testing condition, local face buckling occurred just after reaching the ultimate strength. The ultimate strength is found to be decreasing with increase in the degree of pitting intensity.

A series of non-linear FE analyses has been performed to simulate the deformation behavior observed in the tests. It has been revealed that even in the case of randomly distributed pitting corrosion the ultimate strength of the structural models was almost the same as that of the structural models with uniform corrosion corresponding to the average thickness loss.     

A computational investigation of the effects of both-sides general corrosion on the buckling/plastic collapse behaviour and strength of stiffened plates

This paper presents the results of an investigation into the post-buckling behaviour and ultimate strength of imperfect corroded stiffened steel plates used in ships and other marine-related structures. A series of elastic–plastic large deflection finite element analyses is performed on stiffened steel plates suffering general corrosion wastage with random distribution. General corrosion is introduced into the finite element models using a random thickness surface model. The effects of corroded stiffened plate parameters on the post-buckling and ultimate strengths are evaluated in detail. The stiffeners of different symmetrical or unsymmetrical cross-sections are introduced into the models for analysis. Some distinctions are explored and highlighted between the behaviours of steel plates suffering general corrosion in unstiffened and stiffened cases. Finally, a proposal is given in order to simulate the average stress–average strain relationship of stiffened steel plates having both-surface general corrosion wastage.     

Probabilistic modelling of the ultimate strength of ship plates with non-uniform corrosion

This paper presents the results of a parametric study of probabilistic modelling of the ultimate strength of ship plates with non-uniform corrosion represented by random fields. The load-shortening behaviour of the plates with non-uniform reduction of thickness due to corrosion under longitudinal compression is obtained using a general-purpose nonlinear finite element analysis program. A nonlinear time-dependent corrosion model is used to define the probabilistic characteristics of the random fields based on corrosion data measured in plate elements at different locations of bulk carriers. Based on the probabilistic models derived by Monte Carlo simulation, equations to predict the mean and the 5 % characteristic value of the ultimate strength of plates with non-uniform corrosion are developed. Finally a regression equation is proposed to take into account the effect of non-uniform corrosion patterns in the predictions of the ultimate strength of plates with uniform corrosion.     

Time-variant ultimate longitudinal strength of corroded bulk carriers

Many bulk carrier losses have been reported of late, and one of the possible causes of such casualties is thought to be the structural failure of aging hulls in rough weather. In aging ships, corrosion and fatigue cracks are the two most important factors affecting structural safety and integrity. This paper uses a set of the time-dependent corrosion wastage models for 23 different member locations/categories of bulk carriers previously developed by the authors, based on the available corrosion measurements for existing large bulk carrier structures. Differences due to the location and corrosion severity of every member type are taken into account. The nominal design corrosion values for the primary members are suggested based on the annualized corrosion rates obtained in the present study. The effect of time-variant corrosion wastage on the ultimate hull girder strength as well as the section moduli is studied. The criteria for repair and maintenance of heavily corroded structural members so as to keep the ultimate longitudinal strength at an acceptable level are discussed. Important insights and conclusions developed are summarized.     

考虑腐蚀影响的船舶结构可靠性研究现状与展望

对近年来考虑腐蚀影响的船舶结构可靠性计算各主要研究层面的研究现状做了介绍与评述.通过这一综述可以发现:此领域研究工作重心已由考虑线性、非线性均匀腐蚀的影响逐步向局部腐蚀尤其是点腐蚀方向转变.今后的研究重点为以下三个方面,即:①发展符合基本腐蚀机理、与实测腐蚀数据较为吻合的点腐蚀多指标模型;②确定蚀点几何参数在各类荷载条件下对构件强度的影响;③深入评估腐蚀与疲劳的相互作用对结构可靠性计算的影响.     

船体桁材开孔后的极限强度研究

采用非线性有限元直接计算方法,对轴向受压船体桁材开孔后的极限强度进行系列结构计算分析,并基于有限元数值分析结果,提出轴向受压船体桁材开孔后的极限强度的预报公式.计算结果比较表明,该公式更为合理,其预报具有较高精度.     

Experimental assessment of the ultimate strength of a box girder subjected to severe corrosion

The objective of this paper is to describe the experimental assessment of the ultimate strength of a severely corroded box girder subjected to a uniform bending moment resulting from four-point loading. Three box girders that could simulate the behaviour of midship sections have been deteriorated in corrosive seawater environment to simulate different levels of corrosion degradation of ageing ship structures. During the deterioration process, various parameters have been controlled and the total weight lost was registered. Corroded plate thicknesses have been measured in 212 points and a statistical analysis has been performed. The resulting corrosion wastage has been fitted by a non-linear time variant degradation model. The experimental results of the ultimate strength test of a severely corroded box girder subjected to a four-point loading have been analysed. The load-displacement and moment-curvature relationship is discussed, different failure modes are identified, and the strain gauges readings are analysed.     

大深度载人潜水器极限承载能力非线性有限元分析方法研究

大深度载人潜水器载人舱的极限承载能力是载人潜水器安全性的保障,在设计制造中非常关键。本文基于非线性有限元方法,对大深度载人潜水器球形载人舱极限承载能力进行了分析计算,提出了大深度载人潜水器球形载人舱极限承载能力非线性有限元计算中的影响因素;并与极限承载能力设计新公式计算结果进行对比,验证了本文非线性有限元分析方法和设计新公式的广泛适用性,为大深度载人潜水器建造规范和检验指南的制定奠定了基础。     

联合弯矩作用下含裂纹船体结构剩余极限强度评估方法研究

裂纹损伤对于船体结构来说难以避免,将削弱结构的极限强度,所以研究含裂纹损伤船体结构的剩余极限强度意义重大.对于含裂纹舱段结构,现有的研究主要针对垂向弯矩作用下的剩余极限强度,对于联合弯矩作用下的研究还很欠缺.本文采用非线性有限元分析方法,研究了垂向弯矩和水平弯矩联合作用下含裂纹舱段的剩余极限强度.提出了计算含裂纹船舯舱段在联合弯矩作用下剩余极限强度的计算公式,通过对含裂纹箱型梁的有限元计算结果进行拟合,得到公式中待定系数的表达式.研究结果表明,本文提出的方法可以快速预测船体结构在联合弯矩作用下的剩余极限强度.     

Computation of ultimate strength of locally corroded unstiffened plates under uniaxial compression

Over the past decades there have been many losses of the merchant vessels due to either accidents or exposure to large environmentally induced forces. The potential for the structural capability-degrading effects of both corrosion and fatigue induced cracks are of profound importance and must be both fully understood and reflected in vessel's inspection and maintenance programme. The present study is focused on assessing the effects of localized pitting corrosion which concentrates at one or several possibly large area on the ultimate strength of unstiffened plates. Over 256 nonlinear finite element analyses (FEA) of panels with various locations and sizes of pitting corrosion have been carried out. The multi-variable regression method is applied to derive new formulae to predict ultimate strength of unstiffened plates with localized corrosion. The results indicate that the length, breadth and depth of pit corrosion have weakening effects on the ultimate strength of the plates while plate slenderness has only marginal effect on strength reduction. Transverse location of pit corrosion is also an important factor determining the amount of strength reduction. When corrosion spreads transversely on both edges, it has the most deteriorating effect on strength. It was also found out that the proposed formulae can accurately predict the ultimate strength of unstiffened plate with localized corrosion.     

FPSO舷外排水管及支撑结构强度分析

采用三维势流理论和MORISON公式相结合的方法,预报了FPSO舷外排水管的波浪载荷,并进一步应用梁系方法和有限元方法对排水管及其支撑结构进行了强度评估。为类似海洋工程结构物舷外排水管及支撑结构的波浪载荷预报和强度分析提供了一条解决途径。     

Ultimate hull girder strength of a bulk carrier under combined global and local loads in the hogging and alternate hold loading condition using nonlinear finite element analysis

For bulk carriers in hogging, the most critical situation is the alternate hold loading (AHL) condition with odd numbered holds loaded with high density cargoes and even numbered holds empty. The effect of the local lateral pressure loads should be considered in the assessment of ultimate hull girder strength in the hogging and AHL conditions. In the present paper the ultimate strength of a Capesize bulk carrier hull girder under combined global and local loads in the hogging and AHL condition is extensively and systematically investigated using nonlinear finite element (FE) analysis with ABAQUS software. Since the bulk carrier used as a reference vessel in this study is an old design we also studied the effect of modified scantlings by multiplying the plate thickness in the bottom structure by a design modification factor (DMF). In particular, it should be noted that a DMF of 1.4 gives a design in accordance with the new CSR rules. Based on the results obtained by nonlinear FE analyses, a practical interaction equation is established between global hogging bending capacity and average external sea pressure over the bottom.     

深海载人潜水器耐压球壳极限强度研究

对现有的潜水器耐压壳的研究主要都围绕薄壳结构,而深海载人潜水器耐压球壳,已属于厚壳的范围.国际上还没有均匀外压下厚球壳的解析解,只有美国海军泰勒水池耐压球壳设计公式及俄罗斯相应的公式可以参考.因此本文基于有限元的分析方法,对大深度载人潜水器耐压球壳极限强度进行了研究.通过对有限元参数的比较,提出了一个合理的有限元分析模型,计算结果与实验数据相符,而泰勒水池公式及俄罗斯公式的误差较大.然后计算了一系列半径厚度比下的耐压球壳的极限强度,并研究了初挠度的影响.本文认为对于深海载人潜水器耐压球壳可以直接根据有限元计算确定其极限强度,泰勒水池公式和俄罗斯公式偏于保守;耐压球壳经过精加工,初挠度对于其极限强度的影响不大.为了实用起见,本文还给出了完善耐压球壳极限强度与经典值的比值曲线,以及初挠度效应曲线.