Congestion and safety: A spatial analysis of London

A disaggregate spatial analysis, using enumeration district data for London was conducted with the aim of examining how congestion may affect traffic safety. It has been hypothesized that while congested traffic conditions may increase the number of vehicle crashes and interactions, their severity is normally lower than crashes under uncongested free flowing conditions. This is primarily due to the slower speeds of vehicles when congestion is present. Our analysis uses negative binomial count models to examine whether factors affecting casualties (fatalities, serious injuries and slight injuries) differed during congested time periods as opposed to uncongested time periods. We also controlled for congestion spatially using a number of proxy variables and estimated pedestrian casualty models since a large proportion of London casualties are pedestrians. Results are not conclusive. Our results suggest that road infrastructure effects may interact with congestion levels such that in London any spatial differences are largely mitigated. Some small differences are seen between the models for congested versus uncongested time periods, but no conclusive trends can be found. Our results lead us to suspect that congestion as a mitigator of crash severity is less likely to occur in urban conditions, but may still be a factor on higher speed roads and motorways.     

Incorporating work zone configuration factors into speed‐flow and capacity models

This study aims to develop work zone speed‐flow and capacity models, which incorporate work zone configuration factors including the number of work zones, geometrical alignment, work zone speed limit, and work zone length. On the basis of the traffic data from six work zone sites with various work zone configurations, two nonlinear traffic speed and flow models including work zone configuration factors are developed for the uncongested and congested traffic conditions, respectively. A work zone capacity model is proposed on the basis of the two models. The three models can further be used to examine the effects of work zone configuration factors on the speed‐flow relationship and capacity at work zones. Results show that traffic speed, traffic flow, and work zone capacity increase with the posted speed limit. Traffic speed under uncongested conditions decreases with the geometric alignment, the number of work zones, work zone length, and heavy vehicle percentage. Under congested conditions, the increase of the number of work zones is found to exhibit a larger negative impact on the traffic flow than the increase of geometric alignment. The number of work zones is also found to have the largest negative impacts on work zone capacity, followed by the geometric alignment. Short work zone length exhibits a relatively minor contribution to increasing work zone capacity. Copyright © 2014 John Wiley & Sons, Ltd.     

Identifying the onset of congestion rapidly with existing traffic detectors

From an operations standpoint the most important function of a traffic surveillance system is determining reliably whether the facility is free flowing or congested. The second most important function is responding rapidly when the facility becomes congested. These functions are complicated by the fact that conventional vehicle detectors are only capable of monitoring discrete points along the roadway while incidents may occur at any location on the facility. The point detectors are typically placed at least one-third of a mile apart and conditions between the detectors must be inferred from the local measurements.This paper presents a new approach for traffic surveillance that addresses these issues. It uses existing dual loop detector stations to match vehicle measurements between stations and monitor the entire roadway. Rather than expending a considerable effort to detect congested conditions, the research employs a relatively simple strategy to look for free flow traffic. Whenever a unique vehicle passes the downstream station, the algorithm looks to see if a similar vehicle passed the upstream station within a time window that is bounded by feasible travel times. The approach provides vehicle reidentification and travel time measurement on freeways during free flow and through the onset of congestion. If desired, other algorithms can be used with the same detectors to provide similar measurements during congested conditions. The work should prove beneficial for traffic management and traveler information applications, while promising to be deployable in the short term.     

Practical approach for travel time estimation from point traffic detector data

Accurate estimation of travel time is critical to the success of advanced traffic management systems and advanced traveler information systems. Travel time estimation also provides basic data support for travel time reliability research, which is being recognized as an important performance measure of the transportation system. This paper investigates a number of methods to address the three major issues associated with travel time estimation from point traffic detector data: data filling for missing or error data, speed transformation from time‐mean speed to space‐mean speed, and travel time estimation that converts the speeds recorded at detector locations to travel time along the highway segment. The case study results show that the spatial and temporal interpolation of missing data and the transformation to space‐mean speed improve the accuracy of the estimates of travel time. The results also indicate that the piecewise constant‐acceleration‐based method developed in this study and the average speed method produce better results than the other three methods proposed in previous studies. Copyright © 2011 John Wiley & Sons, Ltd.     

Real-time identification of probe vehicle trajectories in the mixed traffic corridor

This paper proposes three enhanced semi-supervised clustering algorithms, namely the Constrained-K-Means (CKM), the Seeded-K-Means (SKM), and the Semi-Supervised Fuzzy c-Means (SFCM), to identify probe vehicle trajectories in the mixed traffic corridor. The proposed algorithms are able to take advantage of the strengthens of topological relation judgment and the semi-supervised learning technique by optimizing the selection of pre-labeling samples and initial clustering centers of the original semi-supervised learning technique based on horizontal Global Positioning System data. The proposed algorithms were validated and evaluated based on the probe vehicle data collected at two mixed corridors on Shanghai’s urban expressways. Results indicate that the enhanced SFCM algorithm could achieve the best performance in terms of clustering purity and Normalized Mutual Information, followed by the CKM algorithm and the SKM algorithm. It may reach a nearly 100% clustering purity for the uncongested conditions and a clustering purity greater than 80% for the congested conditions. Meanwhile, it could improve clustering purity averagely by 21% and 14% for the congested conditions and 6.5% and 6% for the uncongested conditions, as compared with the traditional K-Means algorithm and the basic SFCM. The proposed algorithms can be applied for both on-line and off-line purposes, without the need of historical data. Clustering accuracies under different traffic conditions and possible improvements with the use of historical data are also discussed.     

Impacts of driving patterns on tank-to-wheel energy use of plug-in hybrid electric vehicles

We evaluate the implications of a range of driving patterns on the tank-to-wheel energy use of plug-in hybrid electric vehicles. The driving patterns, which reflect short distance, low speed, and congested city driving to long distance, high speed, and uncongested highway driving, are estimated using an approach that involves linked traffic assignment and vehicle motion models. We find substantial variation in tank-to-wheel energy use of plug-in hybrid electric vehicles across driving patterns. Tank-to-wheel petroleum energy use on a per kilometer basis is lowest for the city and highest for the highway driving, with the opposite holding for a conventional internal combustion engine vehicle.     

The impact of speed post-processing methods on regional mobile emissions estimation

Average roadway segment travel speeds play an important role in estimating stabilized running vehicle emissions. Currently stabilized, or hot, running emissions are computed based on speeds produced during the travel demand modeling process. Speed data from the travel forecasting models are widely recognized as being insufficiently accurate for air quality purposes. Frequently post-processing techniques are seen as the most cost-effective means of improving the accuracy of the speed estimates. Using the Sacramento Metropolitan area, this paper focuses on the impacts of different speed post-processors on regional peak period emissions inventories. The results indicated that most post-processed speeds produce consistently and significantly higher running emissions, particularly in locations with heavy traffic. The observed differences in emissions between different types of post-processed speeds vary with congestion level, pollutant type and the underlying approach encapsulated in the speed post-processor calculations. The Sacramento case study suggests that the post-processor used to develop speeds for the purposes of calculating on-road emissions inventories can significantly influence the emissions inventories.     

Quantifying the effects of input aggregation and model randomness on regional transportation emission inventories

Accurate road-traffic emission inventories are of great interest to metropolitan planning agencies especially in the appraisal of regional transport policies. Integrated road transport emission models are an effective means of establishing emission estimates, yet their development requires significant investments in data and resources. It is therefore important to investigate which data inputs are the most critical to inventory accuracy. To address this issue, an integrated transport and emissions model is developed using the Montreal metropolitan region as a case-study. Daily regional hydrocarbon (HC) emissions from private individual travel are estimated, including the excess emissions due to engine starts. The sensitivity of emission estimates is then evaluated by testing various levels of input aggregation common in practice and in previous research. The evaluated inputs include the effect of start emissions, ambient weather conditions, traffic speed, path choice, and vehicle registry information. Inherent randomness within the integrated model through vehicle selection and path allocation is also evaluated. The inclusion of start emissions is observed to have the largest impact on emission inventories, contributing approximately 67 % of total on-road HC emissions. Ambient weather conditions (season) and vehicle registry data (types, model years) are also found to be significant. Model randomness had a minimal effect in comparison with the impact of other variables.     

Travel time estimation for urban road networks using low frequency probe vehicle data

The paper presents a statistical model for urban road network travel time estimation using vehicle trajectories obtained from low frequency GPS probes as observations, where the vehicles typically cover multiple network links between reports. The network model separates trip travel times into link travel times and intersection delays and allows correlation between travel times on different network links based on a spatial moving average (SMA) structure. The observation model presents a way to estimate the parameters of the network model, including the correlation structure, through low frequency sampling of vehicle traces. Link-specific effects are combined with link attributes (speed limit, functional class, etc.) and trip conditions (day of week, season, weather, etc.) as explanatory variables. The approach captures the underlying factors behind spatial and temporal variations in speeds, which is useful for traffic management, planning and forecasting. The model is estimated using maximum likelihood. The model is applied in a case study for the network of Stockholm, Sweden. Link attributes and trip conditions (including recent snowfall) have significant effects on travel times and there is significant positive correlation between segments. The case study highlights the potential of using sparse probe vehicle data for monitoring the performance of the urban transport system.     

On the macroscopic stability of freeway traffic

A simple model of traffic flow is used to analyze the spatio-temporal distribution of flow and density on closed-loop homogeneous freeways with many ramps, which produce inflows and allow outflows. As we would expect, if the on-ramp demand is space-independent then this distribution tends toward uniformity in space if the freeway is either: (i) uncongested; or (ii) congested with queues on its on-ramps and enough inflow to cause the average freeway density to increase with time. In all other cases, however, including any recovery phase of a rush hour where the freeway’s average density declines, the distribution of flow and density quickly becomes uneven. This happens even under conditions of perfect symmetry, where the percentage of vehicles exiting at every off ramp is the same. The flow-density deviations from the average are shown to grow exponentially in time and propagate backwards in space with a fixed wave speed. A consequence of this type of instability is that, during recovery, gaps of uncongested traffic will quickly appear in the unevenly congested stream, reducing average flow. This extends the duration of recovery and invariably creates clockwise hysteresis loops on scatter-plots of average system flow vs. density during any rush hour that oversaturates the freeway. All these effects are quantified with formulas and verified with simulations. Some have been observed in real networks. In a more practical vein, it is also shown that the negative effects of instability diminish (i.e., freeway flows increase) if (a) some drivers choose to exit the freeway prematurely when it is too congested and/or (b) freeway access is regulated in a certain traffic-responsive way. These two findings could be used to improve the algorithms behind VMS displays for driver guidance (finding a), and on-ramp metering rates (finding b).     

Variation in the value of travel time savings and its impact on the benefits of managed lanes

This paper examines the variation in the value of travel time savings (VTTS) for travelers with a managed lane (ML) option when taking an ordinary trip versus a trip that is unusual in some way. VTTS estimates vary substantially depending on the urgency of the trip made. At the low end, the mean VTTS for a traveler who wants to make extra stops and still arrive on time is approximately 10% higher than that for an ordinary trip. At the high end, a traveler running late for an appointment shows a mean VTTS that is approximately 300% higher than that for an ordinary trip. These estimates vary widely over the population of travelers. In light of these variations, the value of an uncongested travel alternative (such as MLs) is examined and found to be greatly undervalued if using typical VTTS estimates.     

Safety Effects of Winter Weather: The State of Knowledge and Remaining Challenges

Abstract

In recent years, there has been growing recognition of the effects of weather on the surface transportation system. Although considerable work has been done in quantifying the effects of weather on the highway system, there is still much that remains unknown about the relationship between weather and highway system performance. This paper synthesizes the findings from some of the major efforts in this area. The review of existing studies found consistent patterns that adverse weather reduces traffic speed and increases crash frequencies, while fatal crashes are decreased. A table is then presented which estimates the change in crash frequency and vehicle travel speed resulting from various winter weather conditions, based on a synthesis of earlier work. To estimate the safety and speed adjustment factors of compacted snow, a severity index is also developed. Recognizing the lack of comparability between the results of the studies, the paper concludes with a detailed discussion of avenues for future research which could help to address some of the gaps which currently exist. These challenges include, but are no limited to: quantification of the dynamic layer, development of the relationship between pavement friction and the composition of the dynamic layer, evaluation of the effects of pavement friction on vehicle speed, and evaluation of safety effects of weather conditions above the pavement.     

Speed-spacing dependency on relative speed from the adjacent lane: New insights for car following models

This paper examines the traffic dynamics underlying a recently observed phenomenon, the so called “sympathy of speeds” whereby a high occupancy vehicle (HOV) lane seemingly exhibits lower vehicular capacity and lower flow at speeds throughout the congested regime compared to the adjacent general purpose (GP) lanes. Unlike previous studies this paper examines a time-of-day HOV lane. During the non-HOV periods the study lane reverts to a GP lane, thereby providing a control condition for the specific lane and location. This work uses the single vehicle passage (svp) method to group vehicle passages before measuring the traffic state and extends the svp to bin vehicles in the study lane based on the relative speed to the adjacent lane. The extended svp method allows the work to also study the impacts during the non-HOV periods when the study lane serves GP vehicles. This work finds that: (1) during the non-HOV periods the study lane exhibited behavior indistinguishable from the adjacent GP lane. (2) The sympathy of speeds persists throughout the day, even when the study lane serves GP vehicles. (3) The relative speed to the adjacent lane provided a better predictor of behavior than whether or not the HOV restriction is active. In short, the car following behavior that gives rise to the sympathy of speeds is unrelated to the HOV restriction per se, persisting under GP operations as well.This dependency on the relative speed in the adjacent lane is an important finding given the fact that most existing car following models assume that the longitudinal acceleration of a following vehicle is strictly a function of the relationship to the leading vehicle in the same lane. Because drivers in general adopt a larger spacing when faced with a high differential in speed between lanes means that car following behavior also depends on the relative speed to the adjacent lane. This fact has likely gone unnoticed to date because generally the conditions that give rise to a differential in speeds between lanes are usually short lived, and thus, do not become apparent in conventional macroscopic data except under exceptional circumstances that include confounding factors like HOV operations.     

Energy and emissions impacts of a freeway-based dynamic eco-driving system

Surface transportation consumes a vast quantity of fuel and accounts for about a third of the US CO₂ emissions. In addition to the use of more fuel-efficient vehicles and carbon-neutral alternative fuels, fuel consumption and CO₂ emissions can be lowered through a variety of strategies that reduce congestion, smooth traffic flow, and reduce excessive vehicle speeds. Eco-driving is one such strategy. It typically consists of changing a person’s driving behavior by providing general static advice to the driver (e.g. do not accelerate too quickly, reduce speeds, etc.). In this study, we investigate the concept of dynamic eco-driving, where advice is given in real-time to drivers changing traffic conditions in the vehicle’s vicinity. This dynamic strategy takes advantage of real-time traffic sensing and telematics, allowing for a traffic management system to monitor traffic speed, density, and flow, and then communicates advice in real-time back to the vehicles. By providing dynamic advice to drivers, approximately 10–20% in fuel savings and lower CO₂ emissions are possible without a significant increase in travel time. Based on simulations, it was found that in general, higher percentage reductions in fuel consumption and CO₂ emission occur during severe compared to less congested scenarios. Real-world experiments have also been carried out, showing similar reductions but to a slightly smaller degree.     

Prediction of travel time variability for cost-benefit analysis

Unreliable travel times cause substantial costs to travelers. Nevertheless, they are often not taken into account in cost-benefit analyses (CBA), or only in very rough ways. This paper aims at providing simple rules to predict variability, based on travel time data from Dutch highways. Two different concepts of travel time variability are used, which differ in their assumptions on information availability to drivers. The first measure is based on the assumption that, for a given road link and given time of day, the expected travel time is constant across all working days (rough information: RI). In the second case, expected travel times are assumed to reflect day-specific factors such as weather conditions or weekdays (fine information: FI). For both definitions of variability, we find that the mean travel time is a good predictor. On average, longer delays are associated with higher variability. However, the derivative of variability with respect to delays is decreasing in delays. It can be shown that this result relates to differences in the relative shares of observed traffic ‘regimes’ (free-flow, congested, hyper-congested) in the mean delay. For most CBAs, no information on the relative shares of the traffic regimes is available. A non-linear model based on mean travel times can then be used as an approximation.     

Marginal costs of freeway traffic congestion with on-road pollution exposure externality

The health cost of on-road air pollution exposure is a component of traffic marginal costs that has not previously been assessed. The main objective of this paper is to introduce on-road pollution exposure as an externality of traffic, particularly important during traffic congestion when on-road pollution exposure is highest. Marginal private and external cost equations are developed that include on-road pollution exposure in addition to time, fuel, and pollution emissions components. The marginal external cost of on-road exposure includes terms for the marginal vehicle’s emissions, the increased emissions from all vehicles caused by additional congestion from the marginal vehicle, and the additional exposure duration for all travelers caused by additional congestion from the marginal vehicle. A sensitivity analysis shows that on-road pollution exposure can be a large portion (18%) of marginal social costs of traffic flow near freeway capacity, ranging from 4% to 38% with different exposure parameters. In an optimal pricing scenario, excluding the on-road exposure externality can lead to 6% residual welfare loss because of sub-optimal tolls. While regional pollution generates greater costs in uncongested conditions, on-road exposure comes to dominate health costs on congested freeways because of increased duration and intensity of exposure. The estimated marginal cost and benefit curves indicate a theoretical preference for price controls to address the externality problem. The inclusion of on-road exposure costs reduces the magnitudes of projects required to cover implementation costs for intelligent transportation system (ITS) improvements; the net benefits of road-pricing ITS systems are increased more than the net benefits of ITS traffic flow improvements. When considering distinct vehicle classes, inclusion of on-road exposure costs greatly increases heavy-duty vehicle marginal costs because of their higher emissions rates and greater roadway capacity utilization. Lastly, there are large uncertainties associated with the parameters utilized in the estimation of health outcomes that are a function of travel pollution intensity and duration. More research is needed to develop on-road exposure modeling tools that link repeated short-duration exposure and health outcomes.     

Empirical flow-density and speed-spacing relationships: Evidence of vehicle length dependency

Traffic flow theory has come to a point where conventional, fixed time averaged data are limiting our insight into critical behavior both at the macroscopic and microscopic scales. This paper develops a methodology to measure relationships of density and vehicle spacing on freeways. These relationships are central to most traffic flow theories but have historically been difficult to measure empirically. The work leads to macroscopic flow-density and microscopic speed-spacing relationships in the congested regime derived entirely from dual loop detector data and then verified against the NGSIM data set. The methodology eliminates the need to seek out stationary conditions and yields clean relationships that do not depend on prior assumptions of the curve shape before fitting the data. Upon review of the clean empirical relationships a key finding of this work is the fact that many of the critical parameters of the macroscopic flow-density and microscopic speed-spacing relationships depend on vehicle length, e.g., upstream moving waves should travel through long vehicles faster than through short vehicles. Thus, the commonly used assumption of a homogeneous vehicle fleet likely obscures these important phenomena. More broadly, if waves travel faster or slower depending on the length of the vehicles through which the waves pass, then the way traffic is modeled should be updated to explicitly account for inhomogeneous vehicle lengths.     

A study of traveler behavior under traffic information-provided conditions in the Beijing area

ABSTRACT

The quality of traffic information has become one of the most important factors that can affect the distribution of urban and highway traffic flow by changing the travel route, transportation mode, and travel time of travelers and trips. Past research has revealed traveler behavior when traffic information is provided. This paper summarizes the related study achievements from a survey conducted in the Beijing area with a specially designed questionnaire considering traffic conditions and the provision of traffic information services. With the survey data, a Logit model is estimated, and the results indicate that travel time can be considered the most significant factor that affects highway travel mode choice between private vehicles and public transit, whereas trip purpose is the least significant factor for private vehicle usage for both urban and highway travel.     

The effects of in-car speed limiters: field studies

Field trials in three European countries, the Netherlands, Spain and Sweden were carried out in order to investigate the effects of an in-car speed limiter. The trials were carried out on urban and rural roads including motorways. A so-called unobtrusive instrumented car was used, where all the measuring equipment was hidden. All the speed limit categories in the respective countries, ranging from 30 to 120 km/h were included. The results showed that the effects of the limiter were greatest in free driving conditions outside platoons. However, the limiter also had effects in congested traffic. Momentary high speeds were suppressed effectively, which resulted in less variation of speeds. Approach speeds at roundabouts, intersections and curves became smoother, car-following behaviour became safer in the speed range of 30–50 km/h. On the other hand, in the speed range of 70–90 km/h a slightly higher number of short time-gaps suggested less safe car-following behaviour. Other negative behavioural effects were slightly increased travel time and the increased frustration and stress for the drivers caused by the limiter. The majority of the subjects accepted the speed limiter as a driver-operated system. Half of the drivers would accept the limiter voluntarily in their cars.