An adaptive integrated algorithm for active front steering and direct yaw moment control based on direct Lyapunov method

In this article, an adaptive integrated control algorithm based on active front steering and direct yaw moment control using direct Lyapunov method is proposed. Variation of cornering stiffness is considered through adaptation laws in the algorithm to ensure robustness of the integrated controller. A simple two degrees of freedom (DOF) vehicle model is used to develop the control algorithm. To evaluate the control algorithm developed here, a nonlinear eight-DOF vehicle model along with a combined-slip tyre model and a single-point preview driver model are used. Control commands are executed through correction steering angle on front wheels and braking torque applied on one of the four wheels. Simulation of a double lane change manoeuvre using Matlab^®/Simulink is used for evaluation of the control algorithm. Simulation results show that the integrated control algorithm can significantly enhance vehicle stability during emergency evasive manoeuvres on various road conditions ranging from dry asphalt to very slippery packed snow road surfaces.     

基于功能安全的分布式驱动电动汽车前轮失效补偿控制

分布式驱动电动汽车可以实现四轮转矩分配和差动转向,提升整车的动力学控制性能和经济性,但是四轮转矩独立可控的特点也对功能安全提出挑战。当前轮单侧电机出现执行器故障失效情况时,不仅会产生附加横摆力矩降低车辆安全性,差动转向功能的存在还会使车辆严重偏航。基于此,在设计分布式驱动-线控转向一体化底盘的基础上,基于功能安全提出一种分布式驱动电动汽车前轮失效补偿控制策略。首先建立分布式驱动失效动力学模型,分析前轮失效对车辆状态的影响机理,发现单一的驱动转矩截断控制无法满足车辆状态修正需求;其次设计一套备用的线控转向结构,通过变截距滑模控制算法提高切换状态下线控转向系统的转角跟踪性能,并用台架试验验证跟踪的准确性;然后设计自适应失效诊断观测器实时诊断驱动系统的电机故障,在将对应轮进行驱动转矩截断后,通过模型预测控制算法对车轮转矩重新分配实现纵向和侧向的状态跟踪;最后通过仿真和实车试验验证所提失效补偿控制策略的有效性和可用性。研究结果表明：分布式驱动电动汽车前轮单侧电机失效后,备用的线控转向系统能及时矫正前轮转角,所提出的失效补偿控制策略能够快速恢复车辆的稳定性和路径跟踪能力。     

Method for obtaining the modal properties of articulated trains equipped with independently rotating wheels

Independently rotating wheels in railway vehicles could represent an alternative to standard technology as a solution to dynamic problems such as hunting instability or steering forces in curves. Among the proposed design solutions, the train with independently rotating wheels and with the most practical applications is that developed by Talgo. The Talgo technology is based on the use of a passive steering technique of the wheelset through a mechanism. The absence of automatic control systems means that a careful selection of the mechanical parameters of the vehicle is required to improve its dynamic characteristics. Aspects such as dynamic stability or the effect of vibration on passenger comfort could be analysed by extracting the modal properties of the train from mathematical models. In this article, a methodology for determining the low-frequency modal properties of articulated trains equipped with independently rotating wheels and passive steering system (Talgo-type) is proposed. The singularity of this application based on the use of non-conventional wheelsets necessarily involves the development of a specific methodology.     

Method for obtaining the modal properties of articulated trains equipped with independently rotating wheels

Independently rotating wheels in railway vehicles could represent an alternative to standard technology as a solution to dynamic problems such as hunting instability or steering forces in curves. Among the proposed design solutions, the train with independently rotating wheels and with the most practical applications is that developed by Talgo. The Talgo technology is based on the use of a passive steering technique of the wheelset through a mechanism. The absence of automatic control systems means that a careful selection of the mechanical parameters of the vehicle is required to improve its dynamic characteristics. Aspects such as dynamic stability or the effect of vibration on passenger comfort could be analysed by extracting the modal properties of the train from mathematical models. In this article, a methodology for determining the low-frequency modal properties of articulated trains equipped with independently rotating wheels and passive steering system (Talgo-type) is proposed. The singularity of this application based on the use of non-conventional wheelsets necessarily involves the development of a specific methodology.     

Novel stability control strategy for distributed drive electric vehicle based on driver operation intention

In this paper, a novel direct yaw control method based on driver operation intention for stability control of a distributed drive electric vehicle is proposed. It was discovered that the vehicle loses its stability easily under an emergency steering alignment (EA) problem. An emergent control algorithm is proposed to improve vehicle stability under such a condition. A driver operation intention recognition module is developed to identify the driving conditions. When the vehicle enters into an EA condition, the module can quickly identify it and transfer the control method from normal direct yaw control to emergency control. Two control algorithms are designed. The emergency control algorithm is applied to an EA condition while the adaptive control algorithm is applied to other conditions except the EA condition. Both simulation results and real vehicle results show that: The driver module can accurately identify driving conditions based on driver operation intention. When the vehicle enters into EA condition, the emergent control algorithm can intervene quickly, and it has proven to outperform normal direct yaw control for better stabilization of vehicles.     

分布式驱动电动汽车转向工况转矩分配控制研究

针对分布式驱动车辆转向工况在低速下期望提高转向机动性能,高速下期望保证行驶稳定性的需求,充分考虑转向行驶内外侧车轮的转向关系以及车辆动力学,制定了适应车速变化的四轮转矩分配策略,建立了四轮轮毂电机驱动模型以及二自由度参考模型。为了改善分布式驱动转向机动性能,建立自抗扰控制器调整内外侧车轮转矩,形成合理的转速差,减小转向半径,以提高转向机动性;对于高速转向行驶稳定性的需求,通过二次规划方法优化分配各车轮驱动力矩,分析轮胎纵横向附着裕度建立目标函数,并加入附加横摆力矩和路面附着力的限制,进行车轮驱动转矩的在线优化分配,提高车辆转向行驶的稳定性;另外为避免2种控制模式转换时驱动转矩突变,根据车速和稳定性参数制定模糊规则决策2种模式的协调系数,保证2种控制模式的平滑过渡。基于CarSim和MATLAB/Simulink进行联合仿真,并搭建硬件在环平台进行试验,对所提出的方法进行验证。结果表明：在低速转向工况下,提出的分配策略能够调节内外侧车轮产生差速效果,与转矩平均分配的策略相比,转向半径有所减小,提高车辆机动性;高速转向工况下,分配策略能够保证车辆稳定转向,与未考虑稳定性控制的分配策略相比,能更好地跟踪目标轨迹,且横摆角速度控制在参考横摆角速度附近,证明了所提控制策略的有效性。     

An Emergency Obstacle Avoidance Control Strategy for Automated Highway Vehicles

Summary This paper presents an emergency obstacle avoidance control strategy that may be used in automated highway vehicles. In the proposed control strategy, an inverse vehicle dynamics problem is solved on the selected emergency lane-change path to find out the nominal feedforward control inputs such as the steering wheel angle and the braking force. Then the overall vehicle lateral and yaw motion is controlled additionally in the feedback path by an active yaw moment for stability augmentation as well as a corrective steering angle that is added to the nominal steering angle in order to compensate for uncertainties involved in the nominal control input computation. The proposed control strategy has been tested by an ABS Hardware-In-the-Loop Simulation (HILS) system for rapid and safe control prototyping in a lab. Simulation results with a sample emergency avoidance distance (45 m) show that the proposed control strategy may be used as a feasible obstacle avoidance strategy for automated highway vehicles.     

商用车双转向桥中间杆系优化设计

商用车双转向桥包含两个独立的转向梯形机构,它们之间的运动是通过中间杆系来传递的.在设计双转向桥转向系统时,为了避免转向桥轮胎异常磨损,需要两个转向桥的车轮转角协调变化.提出了一种对现有双转向桥中间杆系优化设计的方法,可协调车辆第一、第二转向桥的转角关系,避免了横向滑移导致的双前桥车轮转向时造成的轮胎异常磨损.     

An Emergency Obstacle Avoidance Control Strategy for Automated Highway Vehicles

Summary This paper presents an emergency obstacle avoidance control strategy that may be used in automated highway vehicles. In the proposed control strategy, an inverse vehicle dynamics problem is solved on the selected emergency lane-change path to find out the nominal feedforward control inputs such as the steering wheel angle and the braking force. Then the overall vehicle lateral and yaw motion is controlled additionally in the feedback path by an active yaw moment for stability augmentation as well as a corrective steering angle that is added to the nominal steering angle in order to compensate for uncertainties involved in the nominal control input computation. The proposed control strategy has been tested by an ABS Hardware-In-the-Loop Simulation (HILS) system for rapid and safe control prototyping in a lab. Simulation results with a sample emergency avoidance distance (45 m) show that the proposed control strategy may be used as a feasible obstacle avoidance strategy for automated highway vehicles.     

Robust yaw stability control for electric vehicles based on active front steering control through a steer-by-wire system

A robust yaw stability control design based on active front steering control is proposed for in-wheel-motored electric vehicles with a Steer-by-Wire (SbW) system. The proposed control system consists of an inner-loop controller (referred to in this paper as the steering angle-disturbance observer (SA-DOB), which rejects an input steering disturbance by feeding a compensation steering angle) and an outer-loop tracking controller (i.e., a PI-type tracking controller) to achieve control performance and stability. Because the model uncertainties, which include unmodeled high frequency dynamics and parameter variations, occur in a wide range of driving situations, a robust control design method is applied to the control system to simultaneously guarantee robust stability and robust performance of the control system. The proposed control algorithm was implemented in a CaSim model, which was designed to describe actual in-wheel-motored electric vehicles. The control performances of the proposed yaw stability control system are verified through computer simulations and experimental results using an experimental electric vehicle.     

Risk management algorithm for rear-side collision avoidance using a combined steering torque overlay and differential braking

This paper describes a risk management algorithm for rear-side collision avoidance. The proposed risk management algorithm consists of a supervisor and a coordinator. The supervisor is designed to monitor collision risks between the subject vehicle and approaching vehicle in the adjacent lane. An appropriate criterion of intervention, which satisfies high acceptance to drivers through the consideration of a realistic traffic, has been determined based on the analysis of the kinematics of the vehicles in longitudinal and lateral directions. In order to assist the driver actively and increase driver's safety, a coordinator is designed to combine lateral control using a steering torque overlay by motor-driven power steering and differential braking by vehicle stability control. In order to prevent the collision while limiting actuator's control inputs and vehicle dynamics to safe values for the assurance of the driver's comfort, the Lyapunov theory and linear matrix inequalities based optimisation methods have been used. The proposed risk management algorithm has been evaluated via simulation using CarSim and MATLAB/Simulink.     

Desired yaw rate and steering control method during cornering for a six-wheeled vehicle

This paper proposes a steering control method based on optimal control theory to improve the maneuverability of a six-wheeled vehicle during cornering. The six-wheeled vehicle is believed to have better performance than a four-wheeled vehicle in terms of its capability for crossing obstacles, off-road maneuvering and fail-safe handling when one or two of the tires are punctured. Although many methods to improve the four-wheeled vehicle’s lateral stability have been studied and developed, there have only been a few studies on the six-wheeled vehicle’s lateral stability. Some studies of the six-wheeled vehicle have been reported recently, but they are related to the desired yaw rate of a four-wheeled vehicle to control the six-wheeled vehicle’s maneuvering during corning. In this paper, the sideslip angle and yaw rate are controlled to improve the maneuverability during cornering by independent control of the steering angles of the six wheels. The desired yaw rate that is suitable for a six-wheeled vehicle is proposed as a control target. In addition, a scaled-down vehicle with six drive motors and six steering motors that can be controlled independently is designed. The performance of the proposed control methods is verified using a full model vehicle simulation and scaled-down vehicle experiment.     

A novel vehicle dynamics stability control algorithm based on the hierarchical strategy with constrain of nonlinear tyre forces

Direct yaw moment control (DYC), which differentially brakes the wheels to produce a yaw moment for the vehicle stability in a steering process, is an important part of electric stability control system. In this field, most control methods utilise the active brake pressure with a feedback controller to adjust the braked wheel. However, the method might lead to a control delay or overshoot because of the lack of a quantitative project relationship between target values from the upper stability controller to the lower pressure controller. Meanwhile, the stability controller usually ignores the implementing ability of the tyre forces, which might be restrained by the combined-slip dynamics of the tyre. Therefore, a novel control algorithm of DYC based on the hierarchical control strategy is brought forward in this paper. As for the upper controller, a correctional linear quadratic regulator, which not only contains feedback control but also contains feed forward control, is introduced to deduce the object of the stability yaw moment in order to guarantee the yaw rate and side-slip angle stability. As for the medium and lower controller, the quantitative relationship between the vehicle stability object and the target tyre forces of controlled wheels is proposed to achieve smooth control performance based on a combined-slip tyre model. The simulations with the hardware-in-the-loop platform validate that the proposed algorithm can improve the stability of the vehicle effectively.     

基于MPC的分布式驱动越野车辆原地转向控制研究

针对轮毂电机分布式驱动越野车辆在狭小空间快速机动的需求,设计了一种分层结构的原地转向控制策略。基于动力学原理分析了各轮载荷、附着条件对原地转向横摆速度的影响机理,并搭建原地转向运动学模型,上层采用模型预测控制算法设计原地转向理想轨迹以及期望的横摆角速度,开发基于PI滑模控制的横摆运动跟踪算法,通过补偿转向横摆力矩以提高方向角控制的鲁棒性和稳定性,下层以最优轮胎利用率为目标,设计二次规划算法优化分配各轮附加横摆力矩。dSPACE硬件在环测试结果表明,所提出的控制算法可在保证稳定性的前提下实现原地转向,大幅提高了车辆的转向机动性,在方向盘动态输入仿真中,车辆最大转弯半径为0.157 m,转向中心的最大偏移量为3.610 m;同时,驾驶员能对转向过程进行闭环控制,实现了原地转向过程中横摆速度的实时调节。     

基于变权重系数的分布式驱动无人车轨迹跟踪

为了提高分布式无人车轨迹跟踪的精度，提出了基于自主与差动协调转向控制的轨迹跟踪方法。首先，在车辆三自由度模型基础上，基于模型预测控制（MPC）实时计算前轮转角以控制车辆进行自主转向轨迹跟踪。在此过程中，为了提高自主转向下车辆的轨迹跟踪精度与行驶的稳定性，考虑多种因素，利用经验公式及神经网络控制对MPC的预瞄步数和预瞄步长进行多参数调整，实现预瞄时间的自适应控制。其次，在恒转矩需求的情况下，以轨迹偏差为PID控制器的输入及左右轮毂电机转矩为输出进行差动转向控制，实现了差动转向下的轨迹跟踪控制。然后，通过设置权重系数的方法将自主与差动转向相结合。考虑到车辆横纵向动力学因素，采用模糊控制及经验公式对权重系数进行了调整，从而在提高车辆转向灵活性与轨迹跟踪效果的同时保证车辆行驶的稳定性。CarSim与Simulink联合仿真以及实车试验结果表明：与自主转向轨迹跟踪相比，采用变权重系数的协调控制可以在不同的工况下提高车辆的转向灵活性与轨迹跟踪的精度，轨迹跟踪偏差的均方根值改善率达到了11%。所提出的协调转向控制方法可为分布式驱动车辆转向灵活性的提高及轨迹跟踪精度的改善提供一种新的思路。     

Vehicle steering returnability with maximum steering wheel angle at low speeds

In this paper, an analytical model with suitable vehicle parameters, together with a multi-body model is proposed to predict steering returnability in low-speed cornering with what is expected to be adequate precision as the steering wheel moves from lock to lock. This model shows how the steering response can be interpreted in terms of vertical force, lateral force with aligning moment, and longitudinal force. The simulation results show that vertical steering rack forces increase in the restoring direction according to steering rack displacement for both the inner and outer wheels. As lateral forces due to side-slip angle are directed toward the medial plane of the vehicle in both wheels, the outer wheel pushes the steering wheel in the returning direction while the inner wheel does not. In order to improve steering returnability, it is possible to increase the total steering rack force in both road wheels through adjustments to the kingpin axis and steering angle. This approach is useful for setting up a proper suspension geometry during conceptual chassis design.     

汽车转向控制

本文研究侧偏角有约束条件下，汽车四轮转向控制系统的设计问题。根据汽车转向动力学的特点，建立了具有不确定的汽车转向模型，给出了车体质心处侧偏角有约束条件下，二自由度鲁棒四轮转向控制器的设计方法，最后基于ＬＭＩＴｏｏｌ给出了控制器的迭代算法，并给出了仿真计算实例。     

Active approach to Electronic Stability Control for front-wheel drive in-wheel motor electric vehicles

Recently, motion control for electric vehicles has gradually gained respect in automotive society due to increased strictness of vehicle safety evaluation over time. Electronic Stability Control (ESC) is the kernel technology, which refers to two-dimensional motion stabilization. Many investigations have demonstrated that Direct Yaw-moment Control (DYC) is an effective and practical way to carry out the ESC of electric vehicles. However, based on the drive train of conventional steering, conventional approaches are using braking to achieve the DYC. This paper proposes a new ESC based on the construction of DYC. The presented approach is based on a core of individual traction control measures for propulsion wheels. This approach not only constrain the longitudinal slip, but also ensure the performance and the effectiveness of two-dimensional motion control. With a proper control, the vehicle can be maintained to a nearly neutral-steering under high speed turning. Hence, the vehicle’s dynamic stability can be enhanced under aggressive driving by yaw-moment control. Evaluation of the entire control system is performed by well-acknowledged software, which demonstrates that the vehicle’s dynamic stability can be enhanced under aggressive driving by the proposed approach.     

一种减轻装有EPS汽车转向扭矩的控制策略

本文提出了一种新的电动助力转向系统的控制策略,以减小车辆静止时改变方向所需的转向力。以前尝试通过减少不良的转向振动来减少转向扭矩失败的原因是因为高辅助增益往往会产生震荡或增加噪声敏感性。为了消除此种振动,开发出一种基于控制齿轮角速度的控制策略,它是在简化的转向模型的基础上开发出来的。这个实验获得了很好的齿轮角速度的估计值,这样就有可能消除方向盘所有旋转速度下的振动。实验证明在方向盘大转速变换下,转向扭矩显著降低,无振动传输给司机。所提出的控制策略使用一个辅助来获得超过原来的三倍以上的增益。此外,所提出的控制策略不需要补充传感器。     

Transaction of the International Association for Vehicle System Dynamics (IAVSD)

SUMMARY

Automatic steering control algorithm has been proposed, which uses the motion of objects in a visual image (Optical Flow) obtained from an ITV camera looking ahead in the situation without forward vehicles. This algorithm is improved to be applicable to the situation in which the forward tracking course is invisible owing to the interfarence of the forward vehicles. The adjustment of the control parameters against the change in vehicle speed is confirmed by the computer simulation experiments.