Additional 4WS and Driver Interaction

This investigation is based on a complex 4-wheel vehicle model of a passenger car that includes steering system and drive train. The tyre properties are described for all possible combined longitudinal and lateral slip values and for arbitrary friction conditions. The active part is an additional steering system of all 4 wheels, additionally to the driver's steering wheel angle input. Three control levels are used for the driver model that thereby can follow a given trajectory or avoid an obstacle.

The feedback control of the additional 4 wheel steering is based on an observer which can also have adaptive characteristics. Moreover a virtual vehicle model in a feedforward scheme can provide desired steering characteristics.

To get information for critical situations a cornering manoeuvre with sudden u-split conditions is simulated. Further a similar manoeuvre is used to evaluate the reentry in a high friction area from low friction conditions. And finally the performance of the controller is shown in a severe lane change manoeuvre.     

Integrated Control of Active Rear Wheel Steering and Direct Yaw Moment Control

SUMMARY

An integrated control system of active rear wheel steering (4WS) and direct yaw moment control (DYC) is presented in this paper. Because of the tire nonlinearity that is mainly due to the saturation of cornering forces, vehicle handling performance is improved but limited to a certain extent only by steering control. Direct yaw moment control using braking and/or driving forces is effective not only in linear but also nonlinear ranges of tire friction circle. The proposed control system is a model matching controller which makes the vehicle follow the desired dynamic model by the state feedback of both yaw rate and side slip angle. Various computer simulations are carried out and show that vehicle handling performance is much improved by the integrated control system.     

Vergleich einiger Rechen- und Messergebnisse zum Fahrverhalten von Sattelzügen

SUMMARY

In this paper some results of theoretical and experimental investigations on the dynamic directional properties of heavy tractor-semitrailer vehicles are presented.

A nonlinear digital computer model was developed on which the theoretical system analysis is based. This model takes account of the nonUnear tire properties and the friction couple of the fifth wheel. A combination of numerical computation methods (Runge-Kutta and Newton-Raphson techniques) is used for the digital computer simulation.

Full scale road tests with articulated vehicles of 38 ton total weight were conducted for experimental validation of the used theoretical model. As input signals to the vehicle, predetermined steering wheel angle functions were used. The system output signals corresponding to these input functions were measured and stored.

A comparison of the obtained theoretical and experimental results shows a very good qualitative agreement and hence leads to the conclusion that the developed theoretical model can give consistent estimates of the basic dynamic vehicle properties.     

Numerical Simulation of Vehicle Behavior during Straight Line Keeping on Undulating Road Surfaces

SUMMARY

Numerical design of vehicles having optimal straight line stability on undulating road surfaces requires an accurate vehicle model based on knowledge of the relevant phenomena. Therefore, vehicle behavior on undulating straight roads has been analyzed and modeled. Measurements on a flat road surface have shown that the dedicated vehicle model yields accurate simulation results of the steering response to medium steering wheel angle inputs. In addition, the model has been validated by measuring two vehicle responses during normal driving on an undulating straight road: viz. the responses to the small steering wheel angle input and to the input by the global inclination of the road surface.     

An Advanced Steering System with Active Kinesthetic Feedback for Handling Qualities Improvement

SUMMARY

Advanced Steering System with artificial steering wheel torque-active kinesthetic information feedback for improving handling qualities is discussed. Fundamentally the structure of the system may be considered to another form of model following control. In this system, a driver always remains in the control loop and receives steering control information which give him/her a direct hint to steer a steering wheel. This system works as a stability and control augmentation system of the vehicle to improve the vehicle handling qualities both in compensatory and pursuit control task, and is expected to reduce driver's workload. Effects of this system are analyzed in terms of man-machine system characteristics. Identification of driver dynamics was carried out to find why such improvement could be achieved. Availability of the proposed system is verified by analysis, simulator and proving ground tests.     

Comparison of All-Wheel Steerings in the System Driver-Vehicle

SUMMARY

Different load or tires and a drive on an ice-coated road can overcharge a driver to such an extend, that the result may be an accident. Therefore the aim of development is a self-acting compensation of the vehicle to different vehicle transfer behaviour (invariant vehicle behaviour).

The calculation of so called optimal characteristics shows, that only rear-wheel steering cannot realize this aim of development. Therefore an additional front-wheel angle, which is not influenced by the driver, is necessary. A transfer function can be calculated in order to get controlled steering of the rear wheels without the influence of load.

It is not possible to realize optimal characteristics, because the parameters of the vehicle are difficult to measure. Only an optimal diagnosis and control of driving condition realize a relief for the driver in every driving situation in order to avoid most of the accidents.

The often demanded sideslip angle compensation only worsens driving conditions on ice-coated roads. Therefore systems which identify the driving condition themselves have to be favoured in any case.     

Optimal Control of Four Wheel Steering Vehicle

SUMMARY

This paper derives a method of controlling four wheel steering using optimal control theory. The purpose of control is to minimize the sideslip angle at the center of gravity. The control method feeds forward the steering wheel angle and feeds back the yaw velocity and the sideslip angle to the front and rear wheel angles. Theoretical studies show that the sideslip angle is reduced to zero even in the transient state, and that the understeer characteristic and frequency response can be changed regardless of the vehicle static margin. This Paper also examines various characteristics of the influence of the side force nonlinearities of tires and crosswinds.     

Emergency steering control of autonomous vehicle for collision avoidance and stabilisation

ABSTRACT

Collision avoidance and stabilisation are two of the most crucial concerns when an autonomous vehicle finds itself in emergency situations, which usually occur in a short time horizon and require large actuator inputs, together with highly nonlinear tyre cornering response. In order to avoid collision while stabilising autonomous vehicle under dynamic driving situations at handling limits, this paper proposes a novel emergency steering control strategy based on hierarchical control architecture consisting of decision-making layer and motion control layer. In decision-making layer, a dynamic threat assessment model continuously evaluates the risk associated with collision and destabilisation, and a path planner based on kinematics and dynamics of vehicle system determines a collision-free path when it suddenly encounters emergency scenarios. In motion control layer, a lateral motion controller considering nonlinearity of tyre cornering response and unknown external disturbance is designed using tyre lateral force estimation-based backstepping sliding-mode control to track a collision-free path, and to ensure the robustness and stability of the closed-loop system. Both simulation and experiment results show that the proposed control scheme can effectively perform an emergency collision avoidance manoeuvre while maintaining the stability of autonomous vehicle in different running conditions.     

Drive control system design for stability and maneuverability of a 6WD/6WS vehicle

This paper describes a drive controller designed to improve the lateral vehicle stability and maneuverability of a 6-wheel drive / 6-wheel steering (6WD/6WS) vehicle. The drive controller consists of upper and lower level controllers. The upper level controller is based on sliding control theory and determines both front and middle steering angle, additional net yaw moment, and longitudinal net force according to the reference velocity and steering angle of a manual drive, remotely controlled, autonomous controller. The lower level controller takes the desired longitudinal net force, yaw moment, and tire force information as inputs and determines the additional front steering angle and distributed longitudinal tire force on each wheel. This controller is based on optimal distribution control and takes into consideration the friction circle related to the vertical tire force and friction coefficient acting on the road and tire. Distributed longitudinal/lateral tire forces are determined as proportion to the size of the friction circle according to changes in driving conditions. The response of the 6WD/6WS vehicle implemented with this drive controller has been evaluated via computer simulations conducted using the Matlab/Simulink dynamic model. Computer simulations of an open loop under turning conditions and a closed-loop driver model subjected to double lane change have been conducted to demonstrate the improved performance of the proposed drive controller over that of a conventional DYC.     

Design of Optimal Four-Wheel Steering System

SUMMARY

Optimal design of the four wheel steering (4WS) system of the ground vehicle is studied. 4WS vehicles with the optimal control scheme are considered first. General formulation of the optimal control law is developed based on the linear quadratic regulator theory. The vehicle speed function (VSF) based 4WS vehicle with a simple feedback controller is considered as a special case of the optimal system. Two new designs of the VSF 4WS system are proposed and their performances are compared with the optimal 4WS systems and the existing VSF 4WS system. The first system is designed for the maximum stability while the second system is designed to emulate the response of the optimal 4WS vehicle. Advantages of the new VSF designs are discussed.     

Coordinated control strategies for active steering,differential braking and active suspension for vehicle stability,handling and safety improvement

ABSTRACT

In this paper, a coordinated control strategy is proposed to provide an effective improvement in handling stability of the vehicle, safety, and comfortable ride for passengers. This control strategy is based on the coordination among active steering, differential braking, and active suspension systems. Two families of controllers are used for this purpose, which are the high order sliding mode and the backstepping controllers. The control strategy was tested on a full nonlinear vehicle model in the environment of MATLAB/Simulink. Rollover avoidance and yaw stability control constraints have been considered. The control system mainly focuses on yaw stability control. When rollover risk is detected, the proposed strategy controls the roll dynamics to decrease rollover propensity. Simulation results for two different critical driving scenarios, the first one is a double lane change and the other one is a J-turn manoeuvre, show the effectiveness of the coordination strategy in stabilising the vehicle, enhancing handling and reducing rollover propensity.     

Adaptive Control of 4WS System by Using Neural Network

SUMMARY

An adaptive control system of the model following type is proposed for drive motion control of a four wheel steering (4WS) car with using neural network (NN) which has mastered nonlinear friction force between tire and road surface. A model of one rigid body is adopted which represents appropriately two kinds of car motion caused by steering action, namely the lateral displacement and the yawing rotation, and an equation of motion is described in a simplified form to make a system equation for motion control possible. Nonlinear relation between the cornering force of tire and the slip angle is obtained by numerical analysis with the tire model proposed by E. Fiala, taking friction coefficient and car speed as the parameters. The result is used as the teaching signal for NN. Three NN are used in the control system composed of both the feed-forward and the feedback circuits in order to realize adaptive control. Validity and usefulness of the proposed adaptive control system with NN are verified by three kinds of computer simulation.     

Development and Evaluation of Vehicle Simulation Models for a 4WS Application

SUMMARY

In the scope of the European Prometheus project a passenger car with active rear wheel steering was developed by TNO in cooperation with PSA. During development and engineering of the rear wheel steering system simulation tools have been used to reduce development costs. This paper describes the evaluation of different simulation models, from simple to complex, with results of full vehicle driving tests. The optimal balance for model complexity and accuracy was achieved with a 2-dimensional model with an added roll degree of freedom. The results show that validation using time responses can give ambiguous and inaccurate results, and that frequency response functions are much more usable in validation.     

基于 MPC 的分布式驱动越野车辆原地转向控制研究

针对轮毂电机分布式驱动越野车辆在狭小空间快速机动的需求，设计了一种分层结构的原地转向控制策略。基于动力学原理分析了各轮载荷、附着条件对原地转向横摆速度的影响机理，并搭建原地转向运动学模型，上层采用模型预测控制算法设计原地转向理想轨迹以及期望的横摆角速度，开发基于 PI滑模控制的横摆运动跟踪算法，通过补偿转向横摆力矩以提高方向角控制的鲁棒性和稳定性，下层以最优轮胎利用率为目标，设计二次规划算法优化分配各轮附加横摆力矩。dSPACE 硬件在环测试结果表明，所提出的控制算法可在保证稳定性的前提下实现原地转向，大幅提高了车辆的转向机动性，在方向盘动态输入仿真中，车辆最大转弯半径为 0.157 m，转向中心的最大偏移量为 3.610 m；同时，驾驶员能对转向过程进行闭环控制，实现了原地转向过程中横摆速度的实时调节。     

An adaptive integrated algorithm for active front steering and direct yaw moment control based on direct Lyapunov method

In this article, an adaptive integrated control algorithm based on active front steering and direct yaw moment control using direct Lyapunov method is proposed. Variation of cornering stiffness is considered through adaptation laws in the algorithm to ensure robustness of the integrated controller. A simple two degrees of freedom (DOF) vehicle model is used to develop the control algorithm. To evaluate the control algorithm developed here, a nonlinear eight-DOF vehicle model along with a combined-slip tyre model and a single-point preview driver model are used. Control commands are executed through correction steering angle on front wheels and braking torque applied on one of the four wheels. Simulation of a double lane change manoeuvre using Matlab^®/Simulink is used for evaluation of the control algorithm. Simulation results show that the integrated control algorithm can significantly enhance vehicle stability during emergency evasive manoeuvres on various road conditions ranging from dry asphalt to very slippery packed snow road surfaces.     

Optimization of Vehicles Elasto-Damping Elements Characteristics from the Aspect of Ride Comfort

SUMMARY

Spatial random vibrations of a vehicle that arise during driving represent an important factor in functioning of a dynamic system: Driver - Vehicle - Environment. They carry certain information for driver and also cause fatigue of driver and passenger.

This is the reason why the tendency is towards the minimization of vibratory loads, what in practice can be achieved by optimization of characteristics of elasto - damping elements of a vehicle.

In this paper for optimization of elasto - damping elements of a vehicle we used a complex nonlinear model of a driver and a vehicle during the straight - line motion of the vehicle on a rough road. Optimization was performed by application of the Hooke - Jeeves method and by use of outside penalty functions as well as the objective function that enabled simultaneous optimization of vertical vibrations of the driver's seat, vibrations of the steering wheel, and normal reactions in the contact surface of the tyre and road. The optimization was performed with application of the computer HP 9000/800 SE on the example of a medium passenger car.     

Literature review and fundamental approaches for vehicle and tire state estimation*

ABSTRACT

Most modern day automotive chassis control systems employ a feedback control structure. Therefore, real-time estimates of the vehicle dynamic states and tire-road contact parameters are invaluable for enhancing the performance of vehicle control systems, such as anti-lock brake system (ABS) and electronic stability program (ESP). Today's production vehicles are equipped with onboard sensors (e.g. a 3-axis accelerometer, 3-axis gyroscope, steering wheel angle sensor, and wheel speed sensors), which when used in conjunction with certain model-based or kinematics-based observers can be used to identify relevant tire and vehicle states for optimal control of comfort, stability and handling. Vehicle state estimation is becoming ever more relevant with the increased sophistication of chassis control systems. This paper presents a comprehensive overview of the state-of-the-art in the field of vehicle and tire state estimation. It is expected to serve as a resource for researchers interested in developing vehicle state estimation algorithms for usage in advanced vehicle control and safety systems.     

Advanced emergency braking under split friction conditions and the influence of a destabilising steering wheel torque

The steering system in most heavy trucks is such that it causes a destabilising steering wheel torque when braking on split friction, that is, different friction levels on the two sides of the vehicle. Moreover, advanced emergency braking systems are now mandatory in most heavy trucks, making vehicle-induced split friction braking possible. This imposes higher demands on understanding how the destabilising steering wheel torque affects the driver, which is the focus here. Firstly, an experiment has been carried out involving 24 subjects all driving a truck where automatic split friction braking was emulated. Secondly, an existing driver–vehicle model has been adapted and implemented to improve understanding of the observed outcome. A common conclusion drawn, after analysing results, is that the destabilising steering wheel torque only has a small effect on the motion of the vehicle. The underlying reason is a relatively slow ramp up of the disturbance in comparison to the observed cognitive delay amongst subjects; also the magnitude is low and initially suppressed by passive driver properties.     

Optimisation of driver actions in RWD race car including tyre thermodynamics

ABSTRACT

The paper presents an innovative method for a lap time minimisation by using genetic algorithms for a multi objective optimisation of a race driver–vehicle model. The decision variables consist of 16 parameters responsible for actions of a professional driver (e.g. time traces for brake, accelerator and steering wheel) on a race track part with RH corner. Purpose-built, high fidelity, multibody vehicle model (called ‘miMa’) is described by 30 generalised coordinates and 440 parameters, crucial in motorsport. Focus is put on modelling of the tyre tread thermodynamics and its influence on race vehicle dynamics. Numerical example considers a Rear Wheel Drive BMW E36 prepared for track day events. In order to improve the section lap time (by 5%) and corner exit velocity (by 4%) a few different driving strategies are found depending on thermal conditions of semi-slick tyres. The process of the race driver adaptation to initially cold or hot tyres is explained.     

Unified decision-making and control for highway collision avoidance using active front steer and individual wheel torque control

ABSTRACT

Collision avoidance is a crucial function for all ground vehicles, and using integrated chassis systems to support the driver presents a growing opportunity in active safety. With actuators such as in-wheel electric motors, active front steer and individual wheel brake control, there is an opportunity to develop integrated chassis systems that fully support the driver in safety critical situations. Here we consider the scenario of an impending frontal collision with a stationary or slower moving vehicle in the same driving lane. Traditionally, researchers have approached the required collision avoidance manoeuver as a hierarchical scheme, which separates the decision-making, path planning and path tracking. In this context, a key decision is whether to perform straight-line braking, or steer to change lanes, or indeed perform combined braking and steering. This paper approaches the collision avoidance directly from the perspective of constrained dynamic optimisation, using a single optimisation procedure to cover these aspects within a single online optimisation scheme of model predictive control (MPC). While the new approach is demonstrated in the context of a fully autonomous safety system, it is expected that the same approach can incorporate driver inputs as additional constraints, yielding a flexible and coherent driver assistance system.