预喷射对轻型车用柴油机排放性能的影响

以某轻型车用柴油机为样机,研究了预喷射对柴油机排放及燃油经济性的影响.研究表明:采用预喷射可以对燃烧室进行预热.缩短主燃烧滞燃期,降低缸内最高燃烧温度,从而降低NOx的排放,同时炭烟排放及燃油经济性要好于单纯推迟喷油提前角的单次喷射方案;随着预喷油量的增加,NOx炭烟和燃油消耗率都有所上升,预喷提前角对轻型车用柴油机燃...     

进气节流对柴油机低负荷性能影响的试验研究

在柴油机上加装节流阀是提升小负荷工况排温、改善排放的途径之一,但会对柴油机的其他性能造成影响。本研究通过给柴油机加装节流阀,研究了进气节流对柴油机小负荷工况性能的影响。试验结果表明:进气节流对柴油机的排温和NOx排放提升明显;柴油机进气节流后缸内压力下降,缸内平均燃烧温度、机械效率升高,滞燃期延长,燃烧始点后移;中低转速小负荷工况,随着节流程度的增加,燃油消耗率和烟度增加;高转速小负荷工况,一定范围内通过进气节流可以实现燃油消耗率和烟度的降低。2 500r/min,29N·m工况,保持EGR阀全开,随着节流程度的增加,NOx和烟度出现同时下降趋势,当空气流量由191.4kg/h降至140.6kg/h时,燃油消耗率、NOx、烟度分别下降了7.9%,58.1%,27.3%,排温提升了42.5%。     

多次喷射对柴油机燃烧与排放影响的试验研究

基于1台高压共轨涡轮增压柴油机,采用不同的预喷正时、预喷油量与后喷正时等,研究了多次喷射对燃烧放热、排放生成与燃油经济性的影响,以实现均质压燃和低温燃烧过程。研究结果表明:随预喷正时提前,缸内峰值压力降低,主燃阶段的滞燃期缩短,NOx和炭烟排放均降低;随预喷油量增加,预喷阶段燃烧的放热率和最大压力升高率增大,NOx和HC排放增大,而PM和CO排放降低;随后喷始点推迟,缸内压力与主放热率峰值差异变小,NOx排放降低,但炭烟排放先增大后逐渐降低。     

后喷参数对柴油机燃烧与排放特性的影响

本文中研究了某电控高压共轨柴油机,在两种不同工况下,后喷参数对发动机的燃烧、排放和油耗的影响规律。结果表明,引入后喷对缸内压力无明显影响,放热率曲线出现二次尖峰,缸内平均温度降低;随着喷油间隔的增大,二次放热率峰值逐渐后移,Soot排放先降后升,喷油间隔对NOx和油耗无明显影响;随后喷油量增加,主燃烧段放热率峰值下降,二次放热率峰值上升,Soot和NOx排放均降低,油耗稍有上升。     

采用缸内后喷和排气管喷油的DOC辅助DPF再生技术的研究

为克服传统喷油助燃再生方式存在的火焰难以形成、点火容易丢失和引起二次污染等问题,采用了缸内后喷与排气管喷油相结合的微粒捕集器(DPF)再生系统。利用台架试验研究了缸内后喷对发动机性能的影响。为满足氧化催化器(DOC)工作温度需求,在发动机排气温度250~350℃范围内的工况进行试验,得到不同工况下的最佳缸内后喷时刻、喷油量和排气管喷油量,并绘制了相应的MAP图。     

燃油多次喷射控制策略对单缸柴油机燃烧与排放特性的影响

基于高压共轨系统对一台单缸柴油机采用燃油预喷射控制策略时的燃烧特性与排放特性变化规律进行了研究。在保持循环油量不变的前提下,通过控制每循环燃油的喷射次数、预喷油量、预喷与主喷的间隔角,对发动机缸内燃烧压力、放热规律、压力升高率及排放变化规律进行了分析。试验结果表明：当预喷油量小于5 mg/循环时,发动机能够在维持炭烟颗粒不增加的同时降低NO x的排放,同时发动机的压升率也较无预喷工况有所降低;多次喷射燃烧过程对燃油消耗率的影响较小,较无预喷工况略有上升,但通过对预喷角度、预喷油量及间隔角的合理匹配,能够实现对燃油消耗率的进一步优化。     

预喷参数及EGR对柴油机噪声影响试验研究

柴油机的燃烧过程受喷油次数、喷油时间、喷油量、喷油压力以及EGR开度等参数影响。燃烧过程中缸内缸高频压力振荡与燃烧噪声有很强的关联性。为研究预喷策略以及EGR对4缸高压共轨柴油机整机噪声的影响规律,在柴油机不同方位布置了9个声压传感器,对平均声压级以及频谱特性进行了分析。试验结果表明:在低负荷低循环油量工况下,预喷会使整机噪声恶化;在高负荷高循环油量工况下,少量预喷油量可缩短滞燃期,达到较好的降噪效果,但随着预喷油量的增加,整机噪声仍会恶化;适当延迟主喷可以降低主燃烧对应的峰值频率段声压级;提前预喷会增加预燃烧对应频段的声压级,在频谱图上出现两个声压级峰值;适当地增加EGR开度可以降低整机噪声。     

DPF对柴油机性能影响的仿真研究

利用GT-Power软件,分别建立了柴油机颗粒捕集器(DPF)和D19柴油机的仿真模型,并把二者进行耦合,研究了DPF对D19柴油机的功率、扭矩、缸压及燃油消耗率等方面的影响。研究结果表明,加装DPF会使发动机排气背压升高,输出功率与扭矩下降,缸内最高燃烧压力降低,燃油消耗率上升,且随着载体内颗粒物数量的增加,这种趋势更为明显;当DPF内炭烟加载量接近满载达到10 g/L时,D19发动机的功率、扭矩已有明显的下降趋势,在高转速下最高降幅达4%左右,燃油消耗率增幅为3%左右。     

电控高压共轨柴油机燃用生物柴油-柴油混合燃料的燃烧特性

针对1台6缸增压中冷电控高压共轨柴油机,在不改变原柴油机结构和喷油参数的条件下,研究了生物柴油的掺混比例对发动机燃烧特性的影响。结果表明:小负荷时发动机有预喷射,随着生物柴油掺混比的增大,生物柴油-柴油混合燃料的滞燃期缩短、缸内最高燃烧压力下降,预喷阶段压力升高率峰值和瞬时燃烧放热率峰值减小,且对应的相位提前;主喷阶段压力升高率峰值和瞬时燃烧放热率峰值增大,且对应的相位后移。随着负荷的增大,发动机喷油策略改为单次喷射,随着生物柴油掺混比的增大,缸内最高燃烧压力下降,燃烧持续期缩短,压力升高率峰值略有增大,瞬时燃烧放热率峰值逐渐减小且对应的相位前移。两种不同负荷条件下,随着生物柴油掺混比的增大,混合燃料的指示热效率逐渐下降。     

柴油机燃用生物柴油低温燃烧性能的仿真研究

采用GT-Power软件模拟分析了不同EGR率和喷油正时对柴油机燃用生物柴油低温燃烧性能的影响。研究表明:随着EGR率的增加,最高燃烧压力下降,缸内最高平均温度逐渐升高,燃烧相位后移,有效燃油消耗率增加,热效率降低,NO_x排放大幅度降低,炭烟排放、CO排放和THC排放都升高。在相同的EGR率下,随着喷油正时的延迟,最高燃烧压力和缸内平均燃烧温度降低,燃烧放热相位后移,燃油消耗率先减小后增加,热效率先升高后降低,NO_x排放降低,炭烟排放先升高后降低,CO排放和THC排放同时升高。通过调节EGR率和喷油正时可同时使NO_x排放和炭烟排放低于原机,但是会导致燃油消耗率和热效率大幅度恶化,且CO和THC排放升高。     

不同喷油模式下柴油机可用能分析的试验研究

通过台架试验的方法,对1台0.5L单缸柴油机进行了热力学分析,将缸内燃烧所释放能量的热量分布和可用能分布进行计算和比较,在此基础之上比较了喷油规律相关参数对热平衡的影响,提出了相应减少不可逆损失、提升热效率的解决途径。试验结果表明:在相同工况下,对于不同的喷油模式,燃烧不可逆损失差异不大,差异主要体现在排气损失和其他部分损失;预喷参数和后喷参数对热量分布影响较小,而喷油压力和主喷正时的影响较为明显。随着喷油压力的增大或主喷正时的提前,燃烧不可逆程度降低,排气可用能损失减少,热力循环的热效率得以提升。而对于余热能回收,排气中流失的可用能回收的潜力和价值较大,将这一部分能量妥善地利用可对整机性能起到明显的改善效果,若排气温度从750K降至500K,通过排气余热能的利用可提升指示功20.91%,达到提升动力性和燃油经济性的目的。     

缸内直喷LNG发动机燃烧过程测量分析

将1台直列4缸汽油机改装为缸内直喷LNG发动机,用自行开发的发动机工作过程测量分析系统测量其缸内压力.分析了标定转速和最大扭矩转速下最高燃烧压力、压力升高率、缸内温度的变化,并计算分析了其放热规律.结果表明:与汽油机相比,改装后的天然气发动机燃烧较慢,后燃现象较严重;最大扭矩点的最大压力及最大压力升高率大于标定点;转速...     

外部热EGR对基于优化动力技术的汽油HCCI燃烧的影响

考察了外部热EGR对基于优化动力技术的汽油HCCI发动机燃烧的影响。试验结果表明:外部热EGR可以推迟HCCI燃烧的着火时刻,减缓放热速率,但对于高辛烷值燃料的HCCI燃烧,它对更高EGR率的兼容能力不强,需要提高进气温度来提高燃烧的稳定性;随着EGR率的增加,燃烧持续期延长,缸内温度和压力峰值均减小,指示热效率也随着减小;NOx排放随着EGR率的增加在经过一个"拐点"后始终维持在一个较低的水平,而CO和HC的排放随着EGR率的增加显著增加,燃烧恶化。     

Optimize combustion of compressed natural gas engine by improving in-cylinder flows

In order to solve the problem of slow flame propagation in a spark-ignition engine fueled with compressed natural gas (CNG), the influence of in-cylinder flows on combustion process was investigated in CA6SE3-21E4N CNG-engine by means of numerical simulation and experiment. The status of in-cylinder flows from intake to expansion stroke was described by computational fluid dynamic tool, which revealed that the in-cylinder flows were one of the main reasons of slow burning rate. Therefore, a special-shaped combustion chamber called Cross was used to improve the in-cylinder flows. The results showed that peak turbulent kinetic energy of Cross was 43.9% higher than that of original combustion chamber called Cylinder during the late compression period at 1450 rpm 100% load. The combustion parameters, brake specific fuel consumption (BSFC) and regulated emissions were obtained by means of experiment. At 1450rpm 25%, 50%, 75% and 100% load conditions, the ignition delay of Cross was longer than that of Cylinder, moreover, the Cross produced averagely 5.75°CA shorter combustion duration. The BSFC of Cross was on an average of 4.3% reduction at 1450 rpm as well as the HC and CO emissions were reduced whereas the NOx emissions were significantly increased.     

换气与压缩过程对汽油机燃烧特性的影响研究

针对增压气道喷射汽油机进行了发动机换气与压缩过程对燃烧特性的影响研究,对比了两种状态下的气门升程与配气正时,基于发动机试验台架测试数据,重点分析了发动机动力性、经济性和燃烧特性。试验数据表明了配气相位的改变对燃烧有较大的影响,可使燃烧效率大幅度提高,爆震倾向减小。同时基于AVL-fire软件进行发动机进气与压缩过程三维CFD分析,分析结果表明:对燃烧特性的影响不能仅靠瞬态滚流比和缸内平均湍动能进行判断,真正影响燃烧的是火花塞附近湍动能的变化,即发动机换气与压缩过程对燃烧特性的影响来自压缩上止点火花塞附近的湍动能。     

Effects of Injection Timing on Transient Performance of A Regulated Two-Stage Turbocharged Diesel Engine with Turbine Bypass Valve

The object of this paper is to reduce soot emissions under typical 5s transient conditions of constant speed and increasing torque. And effects of fuel injection timing on combustion and emissions parameters were experimentally and numerically studied in a regulated two-stage turbocharged diesel engine with a turbine bypass valve (TBV). The test results indicated that: the smaller TBV opening could improve deterioration of smoke emissions and BSFC at medium and heavy loads. Afterward, the full-stage injection timing (FSIT) strategies (delaying injection timing during the entire transient process) could reduce soot and NO_X emissions simultaneously. However, when TBV opening became larger, smoke emissions and BSFC were deteriorated gradually. Moreover, the sectional-stage injection timing (SSIT) strategies (advancing injection timing from 10 % load to a preset load and delaying injection timing from the preset load to 100 % load) could markedly reduce soot emissions by 75.8 % with TBV opening 20 %; the degradation of fuel consumption could be effectively suppressed. Finally, coupling the SSIT strategies with the TBV control strategies could significantly improve the transient performance.     

Comparison of HC species from diesel combustion modes and characterization of a heat-up doc formulation

This study summarizes engine speed and load effects on HC species emissions from premixed charge compression ignition (PCI) and conventional diesel combustion, and it evaluates diesel oxidation catalyst (DOC) formulations on a gas flow reactor for the purpose of diesel particulate filter regeneration or lean NO_x trap desulfation. HC emissions are sampled simultaneously by a Tedlar bag for light HC species and by a Tenax TA™ adsorption trap for semi-volatile HC species, and they are analyzed by gas chromatography with a flame ionization detector. The bulk temperature and residence time during combustion are key parameters that are important for understanding the effects of speed and load on engine-out HC emissions. The degree of post-flame oxidation is higher in PCI than in conventional combustion, and it is increased for PCI with a higher speed and load, as indicated by a lower fuel alkanes/THC ratio, a higher alkenes/fuel alkanes ratio, and a higher methane/THC ratio. Ethene and n-undecane are two representative HC species, and they are used as a surrogate mixture in the gas flow reactor to simulate PCI and conventional combustion with in-cylinder post fuel injection. Among the three DOC formulations tested, the catalyst with constituent precious metals of platinum and palladium (PtPd) showed the best light-off performance, followed by PtPd with an addition of cerium dioxide (PtPd+CeO₂), and platinum (Pt), regardless of exhaust compositions. Conventional combustion exhaust composition shows a lower light-off temperature than that of PCI, regardless of catalyst formulation.     

柴油机微粒捕集器催化再生技术

柴油机微粒捕集器（DPF）能降低柴油机的微粒（PM）排放量,文章提出了DPF催化再生技术方案,将氧化催化器（DOC）与DPF相结合,通过DOC催化氧化未燃HC等来提高排气温度达到微粒着火温度500～600℃,点燃微粒从而完成再生过程。以YN4100QB–1A柴油机为研究对象,对不同喷油量下的DPF升温特性进行了试验研究,试验结果表明：当喷油量大于60mL/min时,再生系统能迅速将排气温度提高到500℃以上。可变喷油量的喷油控制方案可使DPF升温平缓,降低再生造成的二次污染。     

大气压力和冷却液温度对柴油机性能影响的试验研究

利用内燃机高海拔(低气压)模拟试验系统,研究了大气压力和冷却液温度对柴油机性能与燃烧特性的影响规律。试验结果表明:随着进气压力降低,柴油机最高燃烧压力下降,缸内平均温度大幅升高,燃烧始点推迟且持续期延长,后燃严重,燃烧过程未能及时释放热量,动力性能和燃料经济性下降明显;随着冷却液温度的升高,最高燃烧压力增大,燃烧始点提前且持续期略有延长,燃烧重心略微前移,燃烧放热率减小,且大气压力越低冷却液温度对柴油机燃烧过程的影响越明显。在高海拔(低气压)条件下,提高柴油机冷却液工作温度,可以明显减少冷却液散热量,提高柴油机的热-功转换效率,显著改善柴油机的高原动力性和经济性,同时柴油机热负荷升高幅度并不大。