船船水动力相互作用的CFD分析研究（英文）

A numerical study of ship-to-ship interaction forces is performed using a commercial CFD code, and the results are compared with experimental data and with the results of a panel method analysis. Two ship models have been used in the interaction forces analysis: a tug and a tanker, advancing parallel to each other with different lateral distances and two different values of the fluid depth. Computations are carried out with four different flow models: inviscid and viscous flow with the free surface modeled as a rigid wall and inviscid and viscous flow with the deformable free surface. A fair agreement was obtained with available experimental data and results obtained by panel method. The influence of viscosity in the computations is found to be comparatively weak, while the wavemaking effects may be important, at small magnitude of the horizontal clearance.     

绕船体粘性自由面流动的数值计算

考虑自由面的船舶粘性流动计算由于其复杂性和对计算机硬伯的较高要求，只是到了最近几年才得到较大发展，而在国内尚属起步阶段。本文使用VOF方法计算了绕Wigley船型的粘性自由面流动，流模式选择了SSTκ-ω模型。计算获得了船体上波形以及船波等值线图，同时考察了三个不同横截面上的流动状况。计算得到的阻力还和发表的试验结果作了对比，结果令人鼓舞。     

潜艇水面与水下粘性绕流数值模拟

本文采用求解RANS方程的方法结合四种湍流模型,对于带有不同附体的SUBOFF模型尾流场进行了数值模拟。数值预报的桨盘面处不同半径上的轴向无量纲速度与试验结果进行了对比,结果表明湍流模型在数值模拟中起到重要作用。潜艇水面航行性能十分重要,因而对于潜艇自由液面绕流的数值模拟备受关注。本文采用VOF方法对于两条潜艇模型在不同傅汝德数下的自由液面绕流进行了数值模拟。计算得到的阻力、波形与试验结果吻合较好。文中也探讨了潜艇自由液面绕流的一般特性。并验证了用CFD手段预报潜艇粘性流场的能力。     

Directly coupled fluid structural model of a ship rudder behind a propeller

A computational method is presented that models fluid structural interaction problems for three-dimensional marine structures. Flow can be modelled with either potential or viscous incompressible flow. The structure deformation is modelled by a shell finite element formulation. The two fields are coupled by a domain decomposition approach that uses virtual surfaces to transfer information. A typical spade rudder has been modelled for steady-state three-dimensional problems in a free stream and in way of a propeller race. These computational models have been tested for mesh dependancy in both the fluid and structural domains as well as the virtual surface definition. The results show increased correlation to experimental data from uncoupled hydrodynamic modelling as well as detailed structural deformation. Of note is the variation in rudder stock bending moment from that utilised by classification society scantling rules.     

Numerical study on the hydrodynamic forces on a ship berthing to quay by taking free-surface effect into account

In the present study, numerical simulation of the berthing maneuver of a ship in the prescribed translational motion is performed. The transient viscous flow and hydrodynamic forces on the hull are calculated by solving the unsteady Reynolds-Averaged Navier–Stokes equations in overset grid system, and the free surface is captured using volume-of-fluid (VOF) approach. The present numerical results have been compared with previous computational results by Toda and available experimental data respectively. Since the effects of the quaywall and free surface are taken into consideration in the present study, it is found that the agreement is significantly better than that resulting from Toda’s 3D CFD based approach. Then the effects of various standoff distances between the ship and quaywall on the lateral forces are investigated. Meanwhile, the detailed transient flow features around the berthing ship are obtained, which are helpful to understand the interactional effects between the ship and quaywall. The present results may provide helpful guidance for vessels’ safe maneuvering in berthing motion and the design of fender system in the quay.     

基于高阶面元法的浅水域中船-船水动力相互作用数值预报

文章开发了一种基于非均匀有理B样条（NURBS）的三维高阶面元法对浅水域中两船会遇和追越时的船-船水动力相互作用进行预报。该方法采用NURBS精确表达船体曲面,采用配置点法满足离散的边界积分方程,在边界面上的源强分布确定之后采用B样条表达物面速度势分布。基于低速假设,忽略了自由面的兴波效应,采用无穷镜像法处理刚性自由面和浅水效应,采用时间步进法在时域内求解速度势。将文中计算结果与基于RANS方程求解的CFD方法和细长体理论方法计算结果比较,验证了该方法的有效性。在此基础上,分别在不同水深、船间横向间距和船速下进行了系列的计算,分析了这些因素对船-船水动力相互作用影响。结果表明,在相同的工况下,船-船会遇时相互作用力比追越时更大,对水深变化更敏感,而对横向间距不如追越时敏感。     

重叠网格在船舶CFD中的应用研究

文章采用RANS方法和重叠网格计算了带自由液面的船舶绕流问题。计算网格采用重叠网格的型式,自由液面的模拟采用单相Level-Set方法,Reynolds应力采用k-ω模型,采用体单元有限差分方法和PISO算法求解RANS方程。文中简要描述了重叠网格和单相Level Set自由液面模拟方法的数学模型及求解。通过对S60单体船型约束模和自由模型采用重叠网格的数值求解及与试验结果的比较表明该重叠可较好地模拟带自由液面船舶自由态绕流问题。另采用重叠网格对一简单的双体船和三体船进行了数值求解,计算结果也表明重叠网格和单相Level-Set方法可较好地模拟带自由液面的船舶绕流问题。     

基于RANS方程的船模兴波阻力分离计算方法及其适用范围研究

运用空气-水两相流RANS方程计算了两型船模的粘性兴波流场,提出了兴波阻力的分离计算方法,并研究了该方法的适用范围.结果表明,在长度傅汝德数低于0.4时,文中对船模兴波阻力及波高的计算结果都与模型试验基本相符,但当长度傅汝德数高于0.4时,计算结果与试验还存在一定的差距.     

A numerical investigation of bubble dynamics based on the potential-flow theory

1 Introduction1 In the past, people researched into the underwater bubble dynamics by combining the theoretical analysis and experimental study, however, theoretical analysis is limited to simple and regular cases and the repeatability and alterability of…     

三体船阻力数值计算及方案优选

采用CFD技术模拟了船池试验三体船型在不同速度下的粘性流场,计算中考虑了自由表面效应影响,数值模拟结果与试验结果进行了比较,然后在此基础上计算了侧体对应于不同纵横向位置时的9种三体船方案的总阻力.分析比较各方案的计算结果后,得出三体船阻力性能较优时侧体布局的一般规律,即侧体纵向位置变化对三体船静水阻力性能影响较大,当侧体横向位置不变,在较高速度时侧体纵向向后布置对阻力性能更有利.最后按阻力性能,从9种计算方案中得出优选方案.     

绕船体自由面周围三维粘性流场的数值模拟

本文采用有限体积法通过求解不可压缩的雷诺平均(RANS)方程数值模拟了包括兴波的三维船体周围的粘性流场,湍流模式使用了子网格尺度模式(SGS)和Baldwin-Lomax模式相结合的混合模式.对于自由表面的处理,采用了任意拉格朗日-欧拉方法,网格为不仅与物体表面贴体,而且与自由表面贴体的动网格,即随着自由表面的变化要不断地重新划分网格.虽然此方法需要很长的计算时间,但能较好地描述船体的兴波情况.本文计算了系列60船模在Fn=0.316,Re=1.9×106时带自由面的粘性流场,计算结果与试验结果吻合较好.，An finite - volume method solving of incompressible RANS Equations is developed for the numeri-cal simulation of three - dimensional viscous flow with free - surface about a ship. A hybrid turbulence mod-el by combining the sub - grid scale (SGS) model and the Baldwin- Lomax model is used in this pa-per. The arbitrary - Lagrange - Euler formulation is devised for the treatment of free surface boundary condi-tion. The boundary - fitted coordinate system is fitted not only to the ship hull surface but also to the freesurface, so the computational grid is regenerated to follow the free surface deformation. Although this methodneeds spend much longer computational time, but it can fairly display wave pattern made by a ship. The nu-merical simulation has been carried out for viscous flow with free surface past Series 60 ship hull at Fn =0. 316, Re = 1.9 × 106. The computed results are in reasonable agreement with experimental measure-ments.     

浅水中低速斜航船舶水动力预报及验证与确认分析

浅水中的斜航船舶受到浅水阻塞效应和不对称流的综合影响。为预报该运动中的船舶水动力,文章采用基于定常雷诺平均纳维—斯托克斯方程的计算流体动力学方法,对浅水中做斜航运动的船舶粘性绕流场进行数值模拟。考虑低航速运动的特点,忽略航速影响下的自由面兴波,由数值计算得到水动力系数在漂角影响下的变化规律。针对计算精度问题,在数值模拟中从验证和确认角度分析和评估计算结果：通过网格收敛性分析分析数值误差与不确定度;结合试验数据考察计算模型的误差。此外,从计算区域尺度、湍流模型、边界条件、船体下沉和纵倾作用方面对模型误差的影响因素进行探讨,可为改进计算模型、提高数值模拟精度提供参考依据。     

带自由面肥大船粘性绕流场的数值模拟

采用直接求解RANS方程的方法对带自由面的肥大型船舶的流场和阻力进行了数值计算,湍流模型选用RNGk-ε两方程模式,自由面的处理采用VOF方法.数值计算结果与已公开试验数据的定量比较相当吻合.计算结果的分析表明:文中发展的CFD计算方法可以满足于带自由面肥大型船舶快速性工程预报的要求.     

Numerical analysis on free surface waves and stern viscous flow of a ship model

This paper deals with numerical techniques for computing the viscous flow past a ship hull with and without a free surface using a Reynolds-averaged Navier-Stokes solver with global conservation. In the first technique, a coarse grid is used to find an approximate solution to the free surface problem. Interpolation of a fine grid is subsequently carried out, and a more exact solution, particularly in the boundary layer and wake, is obtained. In the second technique, a modified Baldwin-Lomax model is introduced to compute the viscous flow with and without a free surface. These numerical techniques are applied to simulations of the flow around a Series 60 and an SR196C ship model. The results are compared with measurement data, and the usefulness of the numerical techniques is demonstrated.     

Hydro- and aerodynamic analysis for the design of a sailing yacht

The results of the design analysis for a sailing yacht’s hull and sails are reported. The results were used to confirm the design of a 30 ft long sloop, which was planned, designed, and built in Korea for the first time in history. Flows around a sailing yacht above and under the free surface were analyzed separately using both computational and experimental methods. For the underwater flow analysis, turbulent flow simulations with and without free surface wave effects were carried out for the canoe hull with keel/rudder. The computed drag and side forces on the hull model were compared with the measurement data obtained from the towing tank experiments. In order to assess the sail performance, another set of computations was carried out for the flow around a sail system composed of main and jib sails with a mast. The present study demonstrates that, for the design analysis of a sailing yacht, computational fluid dynamics techniques can be utilized with a reasonable level of confidence.     

直立圆柱体内孤立波载荷特性数值模拟

以三类内孤立波理论(KdV、eKdV和MCC)的适用性条件为依据,将内孤立波诱导上下层深度平均水平速度作为入口条件,采用Navier-Stokes方程为流场控制方程,建立了两层流体中内孤立波对直立圆柱体强非线性作用的数值模拟方法.结果表明,数值模拟所得内孤立波波形及其振幅与相应理论和实验结果一致,并且直立圆柱体内孤立波水平力、垂向力及其力矩数值模拟结果与实验结果吻合.直立圆柱体内孤立波载荷由波浪压差力、粘性压差力和摩擦力构成,其中摩擦力很小,可以忽略;对于水平力,其波浪压差力与粘性压差力量级相当,流体粘性的影响显著;对于垂向力,粘性压差力很小,流体粘性影响可以忽略.此外,直立圆柱体对内孤立波的波形及其诱导流场的影响很小,因此采用Morison公式和傅汝德—克雷洛夫力分别计算其内孤立波水平力和垂向力是可行的.     

潜艇近水面航行兴波特征研究

潜艇作为一种水下航行器，其近水面运动时产生的绕流场远比无界直航运动时要复杂得多，其近水面航行时对自由液面的影响不容忽视。本文采用粘性流体力学计算方法，对SUBOFF潜艇近水面航行时的粘性绕流场进行模拟，对自由液面的兴波进行计算，并对波形特点进行深入分析。通过本文的研究，得到潜艇近水面航行时自由液面兴波的特点和相关规律。     

带定子导管螺旋桨定常和非定常性能预估的基于速度势的面元法

开发了一个带定子导管螺旋桨定常和非定常水动力性能预报的数值计算方法,该方法采用基于速度势的面元法分别处理绕对带桨毂螺旋桨、导管和定子周围的流动,并通过迭代计算处理它们之间的相互干扰影响.为简化计算,采用了诱导速度的周向平均值来考虑螺旋桨、导管和定子之间定常水动力相互干扰影响.它们之间的非定常水动力相互干扰通过时间域内迭代方法求解,然而螺旋桨泄出涡、导管泄出涡和定子泄出涡之间的非定常干扰采用了时域内简化处理,这样的简化处理既保证了计算精度,又大幅度地减少了计算时间.对于螺旋桨、导管和定子的计算程序分别依次逐个运行直至每个部分的水动力收敛.算例考核表明该数值方法的计算结果与试验数据吻合较好.     

Computational fluid dynamics (CFD) prediction of bank effects including verification and validation

Restricted waters impose significant effects on ship navigation. In particular, with the presence of a side bank in the vicinity of the hull, the flow is greatly complicated. Additional hydrodynamic forces and moments act on the hull, thus changing the ship's maneuverability. In this paper, computational fluid dynamics methods are utilized for investigating the bank effects on a tanker hull. The tanker moves straight ahead at a low speed in two canals, characterized by surface piercing and sloping banks. For varying water depth and ship-to-bank distance, the sinkage and trim, as well as the viscous hydrodynamic forces on the hull, are predicted by a steady state Reynolds averaged Navier–Stokes solver with the double model approximation to simulate the flat free surface. A potential flow method is also applied to evaluate the effect of waves and viscosity on the solutions. The focus is placed on verification and validation based on a grid convergence study and comparisons with experimental data. There is also an exploration of the modeling errors in the numerical method.     

基于完全耦合算法的绕水翼流固耦合特性研究

基于完全耦合算法对绕二维NACA0009水翼流固耦合特性进行了数值模拟研究。采用Theodorsen模型和Munch模型对刚性和弹性水翼的水弹性响应进行了数值计算,分析了流体与结构的相互作用关系,研究了影响结构水弹性响应和流固耦合特性的因素。研究结果表明:考虑了流体黏性的Munch模型与基于势流理论的Theodorsen模型对气动弹性响应的数值计算结果基本一致,而Theodorsen模型由于没有考虑流体黏性在一定程度上低估了结构的水弹性响应。结构的惯性、阻尼和刚度力矩与流体的相应附加载荷均处于同一数量级,故流体与结构的相互作用不可忽略,尤其对于弹性水翼,流体的惯性、附加阻尼作用增大,流固耦合算法的数值稳定性对流固耦合特性的计算结果影响将更大。外部激励频率为非共振频率时,结构的刚度作用是影响水弹性响应的主要因素,外部激励频率为共振频率时,流体的附加阻尼和附加刚度作用减弱,除结构的刚度作用外,流体与结构的惯性作用对水弹性响应和流固耦合特性的影响也较大。