Hysteretic damping model for laterally loaded piles

Fatigue assessment is a critical design aspect for many offshore structures. Soil-foundation interaction has a direct impact on the system dynamic response of these structures. While the stiffness of the soil-foundation interaction influences the system's natural frequency, the damping influences the amplification of the structural response to environmental excitations. This paper presents a simplified model for estimating the soil damping due to nonlinear soil response for pile foundations, which have wide applications in the offshore industry, such as for supporting jacket platforms, wind turbines and wellhead facilities. The proposed model is fundamentally linked to the damping response of the soil measured at element level therefore it offers design engineers an efficient and accurate way to estimate soil-pile interaction damping based on site-specific soil data. Approaches to include the suggested model for structural analysis are also proposed.     

海上风电场风机桩基局部冲刷计算

建设海上风电场时,风机所处的环境十分复杂,在风、浪、流等要素的影响下,风机桩基周围会出现冲刷坑,而风机桩基的局部冲刷深度是工程设计的重要参数.采用胜利埕岛油田海洋平台桩基局部冲刷现场观测资料,对常用的两个桩基局部冲刷经验公式进行验证,并对拟建的风电场工程风机桩基的局部冲刷深度进行计算,计算结果具有一定的参考价值.     

Monitoring of suction bucket jackets for offshore wind turbines: Dynamic load bearing behaviour and modelling

Suction bucket foundations for offshore wind turbines (OWT) have considerable advantages compared to conventional foundation types: Due to the installation process with dead weight and applied negative pressure, noise from pile driving can be completely avoided. In addition, the installation process of the whole substructure, consisting of the buckets connected to the jacket, can be carried out in one work step, which increases efficiency. A prototype of the suction bucket jacket was installed in the wind park ‘Borkum Riffgrund 1’ (North Sea) in August 2014. Due to the pre-installed and comprehensive measuring system, it was possible to monitor all installation and operating phases. The data analysis of a storm event show an amplitude and frequency-dependent behaviour of the soil stiffness and the suction bucket foundation without wind turbine. In the frequency range of the first and second eigenfrequency (0.2 Hz < f < 5 Hz), the system behaves linearly. Here, the Frequency Domain Decomposition is used for identification and monitoring. For the lower frequency band (0.05 Hz < f < 0.2 Hz) where higher forces and displacements occur, a non-linear multilayer perceptron is chosen to model the non-linear relations between measurements. By applying two mathematical models for the relevant frequency ranges, all the information from the measurement data can be used for system identification and novelty detection under varying environmental conditions.     

深水导管架的运输分析

大型导管架随着国内深水油气田的开发被逐步地采用。导管架拖航由站立运输方式转变为平躺运输方式，运输工况制约水平层桁架的布置和杆件的选取，导管架的重量和尺度对驳船的选择也具有较高的要求。介绍了深水导管架拖航的分析方法和原理，对影响稳性、运动、结构等敏感性参数做了进一步探讨。     

Strain estimation for offshore wind turbines with jacket substructures using dual-band modal expansion

Structural fatigue is a design driver for offshore wind turbines (OWT). In particular, the substructures, like jackets, are strongly affected by fatigue. Monitoring the fatigue progression in the welds is vital for the maintenance and a potential lifetime extension. However, inspections of critical locations are costly due to the limited accessibility of the mostly submerged jacket. Considering the high number of potentially critical welds, it is regarded as economically unfeasible to equip all fatigue hot spots with sensors. Thus, an indirect method to monitor the fatigue progress of the structure and point out critical locations is desirable. For a consistent support of ongoing maintenance, it has to yield reliable results for varying operational and environmental conditions. This paper applies a virtual sensing approach to jacket substructures. From a small set of sensors on the tower, fatigue at every desired location of the jacket is estimated using dual-band modal expansion. Simulations using the OC4 jacket design are performed to show potentials and limitations of the method. Namely fatigue progress on leg welds of K-joints is predicted with high accuracy over a wide range of load cases. However, some difficulties in fatigue prediction of X-joints due to the occurrence of local modes and limitations in the extrapolation of wave loading have to be resolved in future work.     

固定式近岸风机导管架结构完全重叠节点的极限强度研究（英文）

This paper presents an innovative eccentric jacket substructure for offshore wind turbines to better withstand intense environmental forces and to replace conventional X-braced jackets in seismically active areas. The proposed eccentric jacket comprises of completely overlapped joint at every joint connection. The joint consists of a chord and two braces in a single plane. The two braces are fully overlapped with a short segment of the diagonal brace welded directly onto the chord. The characteristic feature of this joint configuration is that the short segment member can be designed to absorb and dissipate energy under cyclic load excitation. The experimental and numerical study revealed that the completely overlapped joint performed better in terms of strength resistance, stiffness, ductility, and energy absorption capacity than the conventional gap joints commonly found in typical X-braced jacket framings. The eccentric jacket could also be designed to becoming less stiff, with an inelastic yielding and local buckling of short segment member, so as to better resist the cyclic load generated from intense environmental forces and earthquake. From the design economics, the eccentric jacket provided a more straightforward fabrication with reduced number of welded joints and shorter thicker wall cans than the conventional X-braced jacket. It can therefore be concluded based on the results presented in the study that by designing the short segment member in accordance with strength and ductility requirement,the eccentric jacket substructure supporting the wind turbine could be made to remain stable under gravity loads and to sustain a significantly large amount of motion in the event of rare and intense earthquake or environmental forces, without collapsing.     

Dynamic impedances and load carrying mechanism for skirted foundations

Dynamic impedances of foundations include dynamic stiffness and damping which have important effect on the internal forces in the structure. In some cases, such as offshore wind turbines, the influence of the foundation impedances on the system's natural frequency and overall damping could potentially have a significant effect on the fatigue life of the structure. The vertical, horizontal and rocking impedances of a skirted foundation (also termed bucket foundation in offshore wind industry) embedded in a fully saturated poroelastic seabed are addressed in this paper. The vertical impedance is most relevant for jacket foundations supported on three or four bucket foundations, while horizontal and rocking impedances are applicable for mono-bucket foundations. The dynamic vibration problems are solved semi-analytically with the help of dual integral equations and Green's functions. Numerical results for dynamic impedances are obtained; damping ratio are also obtained to show the importance of radiation damping for bucket foundations, even at very small excitation frequencies. The influence of length-to-radius ratio, Poisson's ratio, permeability of soil, excitation frequency and thickness-to-radius ratio on the impedances are also studied. Besides, the dynamic load sharing among the top plate, bucket shaft and bucket tip is obtained for vertical load, horizontal load and moment to shed light on the carrying mechanism of bucket foundation at dynamic working loads. It is found that for a rigid bucket foundation, even when the length-to-radius ratio is small (e.g. l/a = 1.0), most of the loads are carried by the shaft, while the top plate and tip of the bucket take only a small portion of the loads. The results of this study will be helpful for understanding the load-carrying mechanism of offshore bucket foundations for normal operation conditions.     

Permanent accumulated rotation of offshore wind turbine monopile due to typhoon-induced cyclic loading

In order to study the effect of typhoons on the accumulated deformation of monopile foundations for offshore wind turbines, a series of 1-g laboratory model tests with a geometrical scale of 1:100 were carried out. Through the horizontal static and cyclic loading tests of a stiff pile embedded in a medium dense sand deposit, the relationship between the accumulated rotation of the pile and the number of loading cycles under different loading conditions was obtained. The results show that the final accumulated rotation is mainly caused by the typhoon load series and is not affected by the loading sequence. Based on these results, a method is presented to predict the accumulated rotation of the monopile foundation during its service life, and a case study of a 6 MW wind turbine supported by a monopile at a water depth of 30 m in sand is conducted by using the method. The results show that the permanent accumulated rotation of the monopile throughout the design life is mainly contributed by cyclic loading induced by typhoons and the contribution of cyclic loading with small amplitudes can be ignored.     

Ultimate Strength of Completely Overlapped Joint for Fixed Offshore Wind Turbine Jacket Substructures

Journal of Marine Science and Application - This paper presents an innovative eccentric jacket substructure for offshore wind turbines to better withstand intense environmental forces and to...     

Numerical investigation of concrete-filled double skin steel tubular (CFDST) structure subjected to underwater explosion loading

With the increasing applications in the offshore industry such as oil and gas jackets, submarine pipelines and wind turbine foundations, concrete-filled double skin steel tubular (CFDST) structures are encountering the ever-increasing risk of threats to underwater explosions (UNDEX). This study presents a systematical investigation on the structural behaviors and design recommendations of the CFDST structures subjected to UNDEX loadings through finite element analysis (FEA) approaches. Finite element models have been developed, where the non-linear material properties of the constitutive steel and concrete parts and the composite actions in-between have been considered. The FEA models are verified against the experimentally determined shock wave pressure history, the deformation shapes, and the residual strength. The full-range analyses were firstly carried out on the structural responses of CFDST structures, including the typical damage patterns and residual strength of the specimen after UNDEX. Then, the parametric studies show that the cross-section hollow ratio, charge weight, and explosion distance play great roles in determining the residual strengths. Thereafter, damage indexes considering the parameter of the hollow ratio and the scaled explosion distance has been formulated, and design recommendations have been suggested accordingly.     

Calibration of safety factors for offshore wind turbine support structures using fully coupled simulations

The offshore wind industry experienced a boost during the last decade in terms of size of wind farms and rated capacity of the wind turbines: towers are getting taller and blades are getting longer, constantly facing new and complex challenges. Because of the relative immaturity of the wind industry, and the fact that the offshore design standards stemmed from the oil and gas industry, it is generally acknowledged that the reliability levels achieved, although not very well understood, might result in partial safety factors not optimal for OWT. This paper addresses this situation by studying the reliability levels delivered by the current standards and assessing the validity of the safety factors through a reliability-based code calibration. The combination of the low probability of failure imposed on the design of OWTs and the computational cost of the aero-elastic time-domain simulations brings out the need to develop new approaches for reliability analyses. In this paper, the reliability analysis is performed using a Kriging surrogate model to approximate the load-effect from the aero-elastic simulations converting expensive-to-evaluate limit state functions to explicit functions. Subsequently, a calibration of the safety factors is carried out using the probabilistic models from literature. The approach is applied to an industry-reference turbine and support structure. The results showed very low probabilities of failure for the most severe design cases and confirm that the safety factors from the IEC are mostly adequate.     

半潜型浮式风机平台研究综述

介绍了半潜型浮式风机的发展现状,基于已有的概念设计方案提出了半潜型浮式风机平台的初步设计流程图和优化设计方向,综述了半潜型浮式风机平台在稳定性、水动力性能和强度分析等性能方面的研究,提出了在这些研究领域中有待进一步解决的问题。结果表明,目前半潜型浮式风机在技术上已是可行的,但高成本制约了大规模应用,因此需在技术和成本上进一步优化。     

Semi-submersible wind turbine hull shape design for a favorable system response behavior

Floating offshore wind turbines are a novel technology, which has reached, with the first wind farm in operation, an advanced state of development. The question of how floating wind systems can be optimized to operate smoothly in harsh wind and wave conditions is the subject of the present work. An integrated optimization was conducted, where the hull shape of a semi-submersible, as well as the wind turbine controller were varied with the goal of finding a cost-efficient design, which does not respond to wind and wave excitations, resulting in small structural fatigue and extreme loads.The optimum design was found to have a remarkably low tower-base fatigue load response and small rotor fore-aft amplitudes. Further investigations showed that the reason for the good dynamic behavior is a particularly favorable response to first-order wave loads: The floating wind turbine rotates in pitch-direction about a point close to the rotor hub and the rotor fore-aft motion is almost unaffected by the wave excitation. As a result, the power production and the blade loads are not influenced by the waves. A comparable effect was so far known for Tension Leg Platforms but not for semi-submersible wind turbines. The methodology builds on a low-order simulation model, coupled to a parametric panel code model, a detailed viscous drag model and an individually tuned blade pitch controller. The results are confirmed by the higher-fidelity model FAST. A new indicator to express the optimal behavior through a single design criterion has been developed.     

基于环境因素的海上风机支撑结构方案比选多级模糊决策

海上风电是最有前途的清洁能源之一,在概念设计时,海上风机的支撑结构选型优化非常重要。选型优化是一个多属性决策问题,本文将广泛应用的多因素、多层次模糊优选理论引入支撑结构的选型决策中。针对环境等影响因素复杂、确定隶属函数主观因素较强的问题, 成功引入因素的优先关系法来确定优选矩阵的隶属度,较好地减少了确定隶属函数的人为影响。通过此优选模型成功地将四种优选方案(单桩,三脚架,五桩,高桩门架)和影响支撑结构选型的8种因素(施工难度,维护成本,CO2排放量,海水浑浊度,珊瑚礁形成,强度,刚度,耐久性)进行了多级模糊综合优选决策,得到了比较科学的决策结果,本研究为海上风机支撑结构的方案选型决策提出了一种量化分析的手段。     

Ultimate load analysis of a 10 MW offshore monopile wind turbine incorporating fully nonlinear irregular wave kinematics

Loads from storm waves can in some cases be dimensioning for offshore wind turbine substructures. Accurate determination of nonlinear wave loads is therefore important for a safe, yet economic design. In this paper, the fully nonlinear waves, realized by a fully nonlinear potential wave solver OceanWave3D, are incorporated into coupled aero-servo-hydro-elastic simulations for a reduced set of wave-sensitive design load cases, in comparison with the widely used linear and constrained waves. The coupled aero-elastic simulations are performed for the DTU 10 MW reference wind turbine on a large monopile at 33 m water depth using the aero-elastic code HAWC2. Effect of the wave nonlinearity is investigated in terms of the ultimate sectional moments at tower bottom and monopile mudline. Higher ultimate moments, 5% at tower bottom and 13% at monopile mudline as maximum, are predicated when the nonlinear waves are used. It could be explained by the fact that the extreme nonlinear waves, that are close to the breaking limit, can induce resonant ringing-type responses, and hereby dominate the ultimate load responses. However, the constrained wave approach shows marginal difference compared to the standard linear wave approach. It can be concluded at least for the present configuration that the industry standard approaches (linear and constrained wave approach) underestimate the ultimate load responses on offshore wind turbines in severe sea states.     

Field experiments on laterally loaded piles for an offshore wind farm

Pile foundations are widely used to support offshore wind turbines due to their cost effectiveness and rapid constructions. Offshore piles must be designed with enough capacity to withstand overturning moments caused by wind turbines and other environmental factors such as wave excitations and extreme winds. In this study, a full-scale field experimental test is undertaken to determine the pile behaviour under various lateral loading conditions. A distributed fiber optic sensing technology is used to measure strains along two instrumented piles. The bending moments and lateral deflections are calculated from distributed fiber optic sensors, and then analysed with the various p-y methods. Field measurements indicated that for two offshore piles ZK01 and ZK28 with diameter of 2 m and length of 71.5 m and 77.5 m, the maximum lateral movements under a given lateral load of 800 kN were 369.1 mm and 351.7 mm, respectively. The maximum bending moment occurred at 6.5 m and 5.5 m below seabed level with the corresponding depth of 12.15D and 11.95D for pile ZK01 and ZK28, respectively. The position of “zero crossing” of soil resistance for two instrumented piles is almost the same, even though the piles have different lengths. The lateral deflections and bending moments of the two instrumented piles are predicted by the API and hyperbolic method, which indicates that the hyperbolic method yields larger prediction errors than the API method. A modified p-y approach is then proposed for more reliable predictions when compared with field measurements.     

Modified environmental contour method for predicting long-term extreme responses of bottom-fixed offshore wind turbines

Predicting extreme responses is very important in designing a bottom-fixed offshore wind turbines. The commonly used method that account for the variability of the response and the environmental conditions is the full long-term analysis (FLTA), which is accurate but time consuming. It is a direct integration of all the probability distribution of short-term extremes and the environmental conditions. Since the long-term extreme responses are usually governed by very few important environmental conditions, the long-term analysis can be greatly simplified if such conditions are identified. For offshore structures, one simplified method is the environmental contour method (ECM), which uses the short-term extreme probability distribution of important environmental conditions selected on the contour surface with the relevant return periods. However, because of the inherent difference of offshore wind turbines and ordinary offshore structures, especially their non-monotonic behavior of the responses under wind loads, ECM cannot be directly applied because the environmental condition it selects is not close to the actual most important one.The paper presents a modified environmental contour method (MECM) for bottom-fixed offshore wind turbine applications. It can identify the most important environmental condition that governs the long-term extreme. The method is tested on the NREL 5 MW wind turbine supported by a simplified jacket-type support structure. Compared to the results of FLTA, MECM yields accurate results and is shown to be an efficient and reliable method for the prediction of the extreme responses of bottom-fixed offshore wind turbines.     

Estimation of natural frequencies and damping using dynamic field data from an offshore wind turbine

The dynamic characteristics of offshore wind turbines are heavily affected by environmental loads from wave and wind action and nonlinear soil behaviour. In the design of the monopile structures, the fatigue load due to wind and wave loading is one of the most important problems to consider. Since the fatigue damage is sensitive to the foundation stiffness and damping, increasing the accuracy of analysis tools used in the design and optimization process can improve the reliability of the structure and reduce conservatism, thereby leading to a more cost-efficient design. In this context, analysis of field data is important for calibrating and verifying purposes. This paper presents analysis of measured accelerations and strains from a wind farm in the North Sea with monopile foundations. Field data during idling conditions, collected over long periods of operation, are analysed and the natural frequencies are determined, and damping is estimated. The measured natural frequencies are compared to calculated values using an aero-servo-hydro-elastic code, showing a good agreement in the frequency range below 2 Hz. Variation of the natural frequencies with intensity of loading may indicate effect of soil nonlinearity on the overall OWT response. Since the first natural bending modes have the largest potential to mobilize soil reactions, they are of primary interest in this context. The effect of load (wave, wind and dynamic bending moment) on the first natural frequency is investigated using different analysis techniques in the frequency domain and time domain. A clear correlation between load level and first natural frequency is demonstrated. A simple nonlinear SSI model of the tower/soil system is employed to numerically investigate the observed changes in the measured first natural frequency with the level of loading and increased overall damping. The simulated results reproduce the general trends in the observed reduction in the first natural frequency and increased damping ratio with the load level. However, the effect of the load level is less than that observed in the measurements, indicating contribution also from other factors than soil nonlinearity.     

浮式海上风力机运动性能和锚泊系统(英文)

The development of offshore wind farms was originally carried out in shallow water areas with fixed(seabed mounted) structures.However,countries with limited shallow water areas require innovative floating platforms to deploy wind turbines offshore in order to harness wind energy to generate electricity in deep seas.The performances of motion and mooring system dynamics are vital to designing a cost effective and durable floating platform.This paper describes a numerical model to simulate dynamic behavior of a new semi-submersible type floating offshore wind turbine(FOWT) system.The wind turbine was modeled as a wind block with a certain thrust coefficient,and the hydrodynamics and mooring system dynamics of the platform were calculated by SESAM software.The effect of change in environmental conditions on the dynamic response of the system under wave and wind loading was examined.The results indicate that the semi-submersible concept has excellent performance and SESAM could be an effective tool for floating wind turbine design and analysis.