一种具有鲁棒性的磁链观测器在异步电机直接转矩控制中的应用

对磁链的准确估计在异步电机直接转矩控制中具有至关重要的作用．针对参数不确定电机模型．利用Lyapunov函数方法，给出了一种基于线性矩阵不等式（LMI）的具有鲁棒性的磁链观测器设计方法．得到了磁链观测器辨识的收敛性条件：相对于基于参数辩识磁链估计方法，其计算量很小．容易满足实时性控制的要求、仿真结果表明．磁链受定转子电月且不确定性变化影响较小．具有较强的鲁捧性．     

基于非线性观测器的IPMSM无位置传感器控制

为了解决内嵌式永磁同步电机(IPMSM)无位置传感器控制中转子角度和速度估计问题,根据IPMSM的状态方程和非线性理论,设计了一种非线性状态观测器,并基于Lyapunov稳定性原理讨论了观测器稳定条件.同时考虑负载影响,加入了负载转矩的观测由于模型参数问题和采样精度问题,状态变量的观测值和实际值存在一定误差,因此对角度和速度观测值分别进行了修正.仿真和试验研究表明,改进后的非线性观测器能够准确估计转子角度和速度,可以获得良好的动态和稳态性能.     

考虑横向漂移的船舶路径跟踪自抗扰控制

针对船舶运动系统中内部动态不确定和外部干扰等问题,进行了欠驱动船舶路径跟踪的自抗扰方法研究。利用Backstepping设计参考航向角,并通过线性扩张状态观测器对流干扰和横向运动引起的横向漂移进行估计。其次,根据自抗扰算法对航向进行控制,采用线性扩张状态观测器对外界干扰及内部不确定项进行估计。最后仿真结果表明,在风流干扰下所设计的控制器仍能使船准确地跟踪上参考路径,验证了所提控制方案的有效性。     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Mooring line tension observed through a maximum entropy spectrum

A method for measuring mooring line tension is proposed based on observation of the natural frequencies of the mooring line segment between the winch and the fairlead. The anchor line tension is observed through the string equation where an analytical expression for the line's eigen-frequencies is obtained. The tension is observed on line by utilizing a nonparametric system identification approach in which the peaks of a maximum entropy spectrum of the transverse acceleration measures of the vibrating string are automatically identified. The method is verified against full-scale data from the Troll B floating concrete oil production platform operating in the North Sea. Received for publication on Feb. 24, 1999; accepted on July 26, 1999     

Simultaneous observation of the wheels’ torques and the vehicle dynamic state

The goal of the present study is to show how it is possible to estimate online the individual torques applied at each wheel of an automotive vehicle by using an unknown input observer together with a simple nonlinear state-space model. The necessary measurements are the steering angle, the usual rotation speed of each wheel plus the vertical load at the centre of each wheel. By doing this, this study anticipates the affordability of a new generation of wheel bearing with embedded measurements of transmitted forces. Successful simulated experimentations using a realistic simulator are shown. Validations are done using classical case studies of longitudinal, lateral and coupled dynamics. The present limits and some possible improvements of the proposed method are also discussed.     

Sensitivity analysis of side-slip angle observer based on a tire model

We investigated the sensitivity of an observer based on a tire model using simulation in linear and nonlinear regions. In the linear region, we investigated the influence of vehicle speed by doing the same simulation at three speed levels. In the nonlinear region, the simulation condition was set such that the vehicle became unstable. In the linear region, steering input and cornering stiffness have a relatively large effect on the estimation error because these quantities determine tire side force. In the nonlinear region, the road surface's friction coefficient becomes a crucial factor. In both the regions, the observer is sensitive to yaw rate and longitudinal speed.     

Sideslip angle estimation based on input–output linearisation with tire–road friction adaptation

An adaptive sideslip angle observer considering tire–road friction adaptation is proposed in this paper. The single-track vehicle model with nonlinear tire characteristics is adopted. The tire parameters can be easily obtained through road test data without using special test rigs. Afterwards, this model is reconstructed and a high-gain observer (HGO) based on input–output linearisation is derived. The observer stability is analysed. Experimental results have confirmed that the HGO has a better computational efficiency with the same accuracy when compared with the extended Kalman filter and the Luenberger observer. Finally, a road friction adaptive algorithm based on vehicle lateral dynamics is proposed and validated through driving simulator data. As long as the tires work in the nonlinear region, the maximal friction coefficient could be estimated. This algorithm has excellent portability and is also suitable for other observers.     

基于扩张观测器的船舶动力定位系统反演滑模变结构控制

针对海洋平台船舶动力定位控制系统,结合反演滑模控制与扩张观测器的优势,提出一种基于扩张观测器的船舶动力定位反演滑模控制方法.考虑到系统存在未知外部干扰以及船舶模型参数不确定性的问题,将系统分为内环观测器和外环控制器分别设计,首先利用扩张观测器估计系统的未知状态及不确定项,然后在外环的反演滑模控制器中进行补偿,最后用Lyapunov方法证明系统的稳定性.通过船舶定点控制仿真实验表明,基于扩张状态观测器的反演滑模控制器使得船舶纵荡和横荡的位置及首摇角度逐渐保持在期望值,具有较强的鲁棒性和控制性,能够有效抑制传统滑模控制的抖振问题,有益于船舶工程应用.     

未知时变扰动和输入饱和下的智能船舶鲁棒非线性控制

复杂海况下环境多变并且船舶具有多耦合、强非线性的特点，针对智能船舶定位控制问题，考虑在未知时变扰动和输入饱和约束之下船舶的定位控制问题，结合非线性扰动观测器提出一种带辅助动态系统的鲁棒非线性控制算法。通过Lyapunov理论证明了所提出的非线性扰动观测器与控制器结合后闭环系统的稳定性和信号的一致最终有界性。利用非线性扰动观测器对环境中存在的海浪扰动进行有效的估计处理。最后，通过仿真验证了所提出的控制算法不仅能保证船舶期望的位置和艏向，而且提高了控制速度，具有较好的控制性能。