基于居民出行时间价值的SP调查设计

不同城市和地区的居民出行时间价值研究方法各异,SP调查逐渐成为研究出行时间价值的重要手段。首先系统梳理SP调查的方法、设计、实施和特点。基于北京市第四次居民出行调查的SP分项调查,详细阐述SP调查的技术方案、实施方法、调查规模和抽样方式,重点分析SP调查方案的设计。基于均匀设计方法,采用SP调查和RP调查相结合的方案,通过确定影响因素、设定情景模式和主要参数,基于不同出行方式分别设计了SP调查表格和情景模式卡。通过对北京市SP调查相关实证分析,提出SP调查实施改进的对策建议。     

铑催化剂用水合三氯化铑的制备

水合三氯化铑是制备铑催化剂的关键原材料之一。随着化工及汽车行业的发展,对铑催化剂有了更多的需求,由此对水合三氯化铑的需求量越来越大。本文综述了当前铑催化剂的应用,以及其原材料水合三氯化铑制备技术的研究进展,并且展望了未来水合三氯化铑的制备技术。     

Study on shaft alignment of propulsion shafting system depending on single reaction force supporting position of aft stern tube bearing

Journal of Marine Science and Technology - Trends of large-scale ships have seen propulsion shaft and propeller sizes increase. This has enabled shafts to have greater stiffness, yet has caused...     

台风"莎莉嘉"过境期间某泻湖内波浪特征分析

通过在某岛礁泻湖内布置ADCP波流测量仪器,采集到2016年21号台风"莎莉嘉"期间的波浪数据.结合布置在泻湖口处风速仪的风实测数据,本文对该时间段内的波浪特征进行分析.由波浪统计数据分析发现有义波高随时间的变化趋势与风速的变化趋势高度重合;谱峰周期的变化则要晚于风速的变化;谱峰方向在台风起主导作用期间与风向高度一致.通过分析多个无因次参数以及对风浪和涌浪进行分离发现测点与台风中心距离开始变大的这个时间点有着重要的意义.在该时间点,波长开始变长,波浪由无限水深波浪转变为有限水深波浪.一些波浪特征值,比如谱峰周期、a/L,也发生比较大的变化.此后在七级风半径不再覆盖测点时,该处波浪由风浪转变为涌浪.对波浪谱进行分析发现,在台风主导期间,其谱为单峰谱,其余时间则为双峰谱.     

基于STM32的蓄电池检测系统设计

蓄电池检测系统是蓄电池质量指标中非常重要的一环,直接影响蓄电池的性能和寿命。本文介绍一种以STM32微处理器STM32F103RCT6为核心的铅酸蓄电池高精度智能检测系统,可以同时检测电压、温度、液位,并根据神经网络计算得到电解液密度,用户在上位机完成测试参数设置,自动对电池的各项数据进行存储和报警。文中详细介绍了系统组成、硬件和软件设计。实践证明该检测系统满足实际需求。     

离线船舶机电设备振动采集仪系统设计

设计了离线振动采集仪的硬件系统，通过对传感器电源模块的进行了节电控制设计，优化振动信号的采集策略和采集节奏，提出了振动信号数据处理和存储方法，实现了无人关注下自主对船舶机电设备振动信号连续近百天的采集任务。应用结果显示，采集仪系统结果准确可靠，实现了全工况的实船振动数据的采集设备。     

Hybrid process of fabricating high-quality micro wine-glass fused silica resonators

A new hybrid method, which combines improved glass-blown technology with wet etching, is reported to fabricate micro wine-glass resonators with high-quality fused silica. The optimum placement is compared to achieve the resonators with good shell shape. The typical shell diameter is about 4mm and its thickness covers from dozens to hundreds of micrometers. The etching rates in corrosion solutions with different ratios and at different thicknesses of hemispherical shells are studied. We also conclude how to precisely control the thickness. The corrosion solutions with different ratios of HF solution to NH₄F solution make the spherical shells rougher in different degrees. The best roughness is 0.581 nm in the 1: 8 ratio corrosion solution while the original roughness is 0.537 nm. This fact shows that the resonator remains atomically smooth surface. Based on the glassblowing spherical fused silica structure, the thickness of the resonator is effectively controlled by buffered oxide etch (BOE) technology according to the measured etching rate. The measured resonant frequency of the hemispherical shell at ambient pressure and room temperature is 1.75 kHz of rocking mode which is close to the simulated frequency. Using such a low-cost hybrid approach, we can fabricate high-quality microscale resonators in batch.     

减摇复合船型首部构型设计与水池模型试验研究

船舶在波浪中航行时的纵向运动性能是衡量船舶综合航行性能的重要指标.为了改善船舶在波浪中的纵向运动性能,本文基于首部减摇组合附体技术对某型船首部构型进行改造并通过水池模型试验对其静水阻力和耐波性进行了分析研究.在分析该船作业及航区特点的基础上,通过船首部线型改造及减纵摇组合附体构型优化,给出适用于该船的首部构型方案.应用CFD软件和修正切片法进行水动力性能分析,并对船首构型方案进行优选.将优选出的性能较优复合船型方案和原船型开展水池模型静水阻力与耐波性对比试验分析,验证减摇复合船型的静水阻力性能与耐波性能.试验结果表明,改造后的复合船型减纵摇效果明显,对应实船四级海况18节航速下纵摇与首部加速度有义值较原船型降低15%以上;复合船型静水阻力有所增加,实船18节航速下静水阻力增加13.5%.     

Purification effects of C2Cl6 on A00 aluminum

The effects of several fluxes on purification, microstructures and properties of A00 aluminum have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C₂Cl₆ and that the film is floc and mostly composed of Al₂O₃ and pure aluminum, which carries many carbon particles and AlCl₃ not fully volatilized. And then over 50% (mass fraction) of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there are many inclusions which size is under 10 ??m in the microstructure of A00 aluminum purified with C₂Cl₆ or fluxes containing C₂Cl₆. With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100?C150 ??m. In addition, small size inclusions have little affected on tensile strength and micro inclusions under 10 ??m have little affected on elongation.     

Novel experimental strategy for high resolution AFM imaging of membrane-associated bacterial toxins

Bacterial pore-forming toxins （PFTs） are essential virulence factors of many human pathogens. Knowl- edge of their structure within the membrane is critical for an understanding of their function in pathogenesis and for the development of useful therapy. Atomic force microscopy （AFM） has often been employed to structurally interrogate many membrane proteins, including PFTs, owing to its ability to produce sub-nanometer resolution images of samples under aqueous solution. However, an absolute prerequisite for AFM studies is that the samples are single-layered and closely-packed, which is frequently challenging with PFTs. Here, using the prototypical member of the cholesterol-dependent cytolysin family of PFTs, perfringolysin O （PFO）, as a test sample, we have developed a simple, highly robust method that routinely produces clean, closely-packed samples across the entire specimen surface. In this approach, we first use a small Teflon well to prepare the supported lipid bilayer, remove the sample from the well, and then directly apply the proteins to the bilayer. For reasons that are not clear, bilayer preparation in the Teflon well is essential. We anticipate that this simple method will prove widely useful for the preparation of similar samples, and thereby enable AFM imaging of the greatest range of bacterial PFTs to the highest possible resolution.