Development of an LIF image processing technique for measuring drop sizes in a pre-swirl spray

Depth of field effects in laser sheet imaging were considered for droplet sizing of a pre-swirl spray. A pre-swirl spray is formed before the hollow-cone type main-swirl spray from a D.I. gasoline injector, and shows transient characteristics with high axial velocity. A microscopic imaging technique was applied to obtain high spatial resolution LIF tomograms of the pre-swirl spray. A 1 mm thick Nd:YAG laser sheet was used as a light source to make the LIF tomograms that were imaged using a high-resolution CCD camera. The droplet sizing of the pre-swirl spray was carried out using an image processing technique. In the image processing procedure, the laser sheet-straddling large-sized droplets were carefully taken into account to remove the errors caused by the depth of field effects from the limited thickness and the energy distribution of the laser sheet. The mean intensity of the individual droplets and the line profile of the LIF signal around the droplet edge were inspected to screen the laser sheet-straddling large-sized droplets. In order to consider the effects of the size-dependent LIF signal intensity, the size-classified or ensemble-averaged mean intensity of the individual droplets was introduced. The mean droplet sizes such as AMD and SMD were calculated using only screened droplets, and they slightly increase before considering the depth of field effects.     

Links between subjective and objective evaluations regarding the steering character of automobiles

This work presents an experiment on the relationships between subjective and objective evaluations of vehicle handling. Ten cars were examined objectively in several open-loop driving dynamics manoeuvres and subjectively by test persons in typical traffic situations. Results are extracted from a stationary test (the Slowly Increasing Steer Test), and a dynamical test (the Frequency Response Test). The subjective measurements are obtained from drivers on a rural road course via a questionnaire, which was developed to separately investigate the quantity level perception, the so-called “Niveau”, and the more qualitative “Liking”. These subjective “measurements” are embedded into a two-channel definition of “Steering Comfort” as a genus for “Steering Discomfort” and “Character”. The article concentrates on developing a statistical method for the consideration of correlations amongst the subjective/objective data. In doing so, the variance in example subjective Niveau ratings can be significantly explained by several objective quantities. Indicators for co-domains of validated discomfort characteristics and hints for endeavouring character Liking ranges are detected.     

Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges

The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.     

Analysis process of a steering system using a concept model for idle vibration

This paper describes the development of an optimal design process for a steering column system and supporting system. A design guide is proposed at the initial concept stage of the development process to obtain sufficient stiffness of the steering system while reducing the idle vibration sensitivity of the system. Case studies on resonance isolation are summarized, where vibration modes among the systems are separated by applying a vibration mode map at the initial stage of the design process. This study also provides design guidelines for an optimal dynamic damper system using a CAE (computer aided engineering) analysis. The damper FE (finite element) model is added to the vehicle model to analyze the relation between the frequency and the sensitivity of the steering column system. This analysis methodology makes it possible to achieve target performance in the early design stage and reduction of damper tuning activity after the proto car test stage. Through the proposed steering column system development process, a lightweight vehicle with high stiffness is possible prior to the proto build stage. Furthermore, the improved process is expected to contribute to reducing the overall development period and the number of proto car tests necessary to achieve the desired steering system performance.     

Desired yaw rate and steering control method during cornering for a six-wheeled vehicle

This paper proposes a steering control method based on optimal control theory to improve the maneuverability of a six-wheeled vehicle during cornering. The six-wheeled vehicle is believed to have better performance than a four-wheeled vehicle in terms of its capability for crossing obstacles, off-road maneuvering and fail-safe handling when one or two of the tires are punctured. Although many methods to improve the four-wheeled vehicle’s lateral stability have been studied and developed, there have only been a few studies on the six-wheeled vehicle’s lateral stability. Some studies of the six-wheeled vehicle have been reported recently, but they are related to the desired yaw rate of a four-wheeled vehicle to control the six-wheeled vehicle’s maneuvering during corning. In this paper, the sideslip angle and yaw rate are controlled to improve the maneuverability during cornering by independent control of the steering angles of the six wheels. The desired yaw rate that is suitable for a six-wheeled vehicle is proposed as a control target. In addition, a scaled-down vehicle with six drive motors and six steering motors that can be controlled independently is designed. The performance of the proposed control methods is verified using a full model vehicle simulation and scaled-down vehicle experiment.     

Lane-following method for high speed autonomous vehicles

This paper presents a steering control method for lane-following in a vehicle using an image sensor. With each image frame acquired from the sensor, the steering control method determines target position and direction, and constructs a travel path from the current position to the target position either as an Arc-path or S-path. The steering angle is calculated from the travel path thus generated, and the vehicle follows the travel path via motor-control. The method was tested using a vehicle dubbed as KAV (Korea Autonomous Vehicle) along an expressway (Seoul Inner Beltway) trajectory with a variety of radii (50 m ∼ 300 m) while traveling at a speed of 60 km/h to 80 km/h. Compared with an experienced human driver, the method showed little much difference in performance in terms of lane-center deviation. The proposed method is currently employed for high speed autonomous driving as well as for stop and go traffic.     

Modeling children’s school travel mode and parental escort decisions

Understanding of the activity-travel patterns of children is becoming increasingly important to various policy makers. Further, there is also a growing recognition that intra-household interactions need to be explicitly accommodated in travel models for realistic forecasts and policy evaluation. In the light of these issues, this paper contributes towards an overall understanding of the school-travel behavior of children and the related interdependencies among the travel patterns of parents and children. An econometric model is formulated to simultaneously determine the choice of mode and the escorting person for children’s travel to and from school. The 2000 San Francisco Bay Area Travel Survey (BATS) data are used in the model estimation process. Empirical results indicate that the characteristics of child like age, gender, and ethnicity, and employment and work flexibility characteristics of the parents have strong impacts on the mode choice decisions. In addition, the impacts of some of these attributes on the choice of mode to school are different from the corresponding impacts on the choice of mode from school. The distance between home and school is found to strongly and negatively impact the choice of walking to and from school, with the impact being stronger for walking to school. Several land-use and built-environment variables were explored, but were found not to be statistically significant predictors.

Exploring spatial variety in patterns of activity-travel behaviour: initial results from the Toronto Travel-Activity Panel Survey (TTAPS)

Studies of urban travel behaviour typically focus on weekday activities and commuting. This is surprising given the rising contribution of discretionary activities to daily travel that has occurred during the last few decades. Moreover, current understanding of the relationship between travel behaviour and land use remains incomplete, with little research carried out to explore spatial properties of activity-travel behaviour during the off-peak and weekend time periods. Weekend behaviours, for example, influenced by the availability of time and the spatiotemporal distribution of “weekend” destinations, likely produce spatially and temporally distinct activity-travel patterns. Using data from the first wave of the Toronto Travel-Activity Panel Survey (TTAPS), this paper examines an area of research that has received little attention; namely, the presence of spatial variety in activity-travel behaviour. The paper begins by looking at the extent to which individuals engage in spatially repetitive location choices during the course of a single week. Area-based measures of geographical extent and activity dispersion are then used to expose differences in weekday-to-weekend and day-to-day activity-travel patterns. Examination of unclassified activities carried out over a 1 week period reveals a level of spatial repetition that does not materialise across activities classified by type, travel mode, and planning strategy. Despite the inherent spatial flexibility offered by the personal automobile, spatial repetition is also found to be surprisingly similar across travel modes. The results also indicate weekday-to-weekend, and day-to-day fluctuations in spatial properties of individual activity-travel behaviour. These findings challenge the utility of the short-run survey as an instrument for capturing archetypal patterns of spatial behaviour. In addition, the presence of a weekday-to-weekend differential in spatial behaviour suggests that policies targeting weekday travel reduction could have little impact on travel associated with weekend activities.

Quantitative estimation of the influence of surface thermal fronts over chlorophyll concentration at the Patagonian shelf

Eighteen-year (1985–2002) mean monthly SST Pathfinder data with 9 km spatial resolution have been used to estimate surface gradients by finite differences. Then the seasonal climatological means have been calculated from the intensity of these gradients, and surface thermal fronts present in the Patagonian Continental Shelf (PCS) have been located. Moreover, 6 years (1998–2003) of SeaWiFS data with approximately 4 km spatial resolution have been used to estimate monthly composite images of surface chlorophyll concentration, after which seasonal climatological means distributions have been generated. Both seasonal distributions have been analyzed together and by combining the knowledge of oceanographic processes and phytoplankton responses to light and nutrient availability, regions where the presence of a thermal front affects photosynthetic activity have been identified. Subjective criteria have been applied to define eighteen areas where phytoplankton biomass is influenced by the presence of a thermal front. In these areas, the surface chlorophyll (spatial mean and total), its relationship with the surface chlorophyll of the whole region, and the seasonal evolution of this relationship have been calculated. All frontal areas cover less than 15% of the total surface, but they contribute with over 23% of the phytoplankton annual mean biomass. Considered as a group, during summer they show high chlorophyll values very similar to those in spring. During the cold period, when the water column is vertically mixed in practically the whole of PCS, the influence of physical fronts over the biological production is minimum. The frontal zone image remains clearly defined during summer, when approximately 85% of the area will have a determined mean chlorophyll concentration, while the other 15% has a 2.45 times larger value. While three pattern trends have been identified in the frontal areas, only two of them condition the pattern of the group, due to their horizontal extension.