光学仪器法快速找寻轴系理论中心线的研究

舰船轴系装调过程中,理论中心线的确定方法有多种。本文采用光学仪器法快速找寻轴系理论中心线,理论支持性强,高效而独特,具有较强的实用性。     

土工格栅在治理沥青路面裂缝中的应用

裂缝是沥青路面常见病害。应用非织造土工织物——多功能双向土工格栅治理高等级公路沥青路面的裂缝,取得了良好的效果,并对土工格栅的应用进行了定量计算。     

石河道大桥桩基础施工

针对卵石地层桩基础成孔问题,根据石河道大桥实际施工实践介绍了应用冲击钻孔的方法加以解决的施工方法,并着重分析了该方法的工艺流程和内容,以及施工中的注意事项.     

船舶总纵极限强度模糊可靠性研究

本文以模糊数学和结构可靠性基本理论为基础,分析了传统随机可靠性理论的不足,并在常规模糊可靠性理论研究的基础上,利用模糊集合与普通集合之间的转换关系,研究了模糊变量组合时的可靠性计算方法,拓展了模糊可靠性理论的使用范围.通过对模糊可靠度计算结果分析发现,模糊可靠性理论使设计更加科学,更加符合工程实际;模糊变量组合在船舶总纵极限强度可靠性上的应用,避免了传统计算方法由于变量统计数据不足而导致的偏差,减少了很多繁复的数学运算.算例分析验证了本文方法的准确性和实用性.     

船舶电站控制系统中的数据融合技术探讨

船舶电站是船舶电力系统的重要组成部分。随着电力电子设备在船舶中的大量应用,非线性负载的增多,对船舶电站控制的可靠性及故障预防提出了更高的要求。多传感器数据融合技术是近年发展起来的一门新兴技术,文章根据多传感器数据融合技术的基本思想,采用扩张的卡尔曼滤波法对电站参数进行冗余数据融合,在船舶电站控制的实时性和可靠性方面取得了较好的效果。     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

Determination of Critical Slip Surface of Soil Slope

A new complex method is presented considering not only the improvement upon the ＂bad ＂design point, but also the diversity of the newly generated complex, which is obtained by replacing the ＂bad ＂design point with the better design point located at the line between the ＂bad ＂design point and the ceotroid of the remaining design points of the old complex. The new complex method is applied to searching for the critical slip surface of two non-homogeneous soil slopes. The comparison of the results obtained by the new complex method with that by the basic complex method shows that the new complex method is much more likely to find the true critical surface for the randomly generated initial complex.     

基于ANN星识别算法的仿真平台

星敏感器是一种高精确度的姿态测量仪器，它通过对观测到的星点进行识别来计算姿态。为了能够较好地测试和验证星识别系统的性能，设计了一个基于ANN算法的星识别仿真平台。通过对该星识别仿真平台性能的测试，表明该仿真平台能够方便，实时地测试星识别算法的性能与正确性，因此说它是一种具有较好实用价值的星识别仿真平台。     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

Numerical simulation of the flow about self-propelling tanker models

A time-marching CFD simulation is performed for self-propelling ships. The flow about the hull is simulated by the finite-volume method, and the propeller action is approximated as a propeller disk for which the solution is given by a simplified propeller model. The interaction of two flow models is treated in a time-marching procedure converging towards the steady self-propelling condition. This method is applied to five tanker models, and detailed comparisons are made between the simulated results and corresponding experimental results. It is shown that the flow field in the self-propelling condition is qualitatively well reproduced in the simulation, and the estimated thrust deduction factors for the five hull forms agree well with measured ones. However, the effective wake factors are underestimated, since the Reynolds number in the simulations differs from that in the experiment.