S^2 BHCA Multiple AUVs cooperation oriented control architecture

Oceanographic survey, or other similar applications should be the applications of multiple AUVs. In this paper, the skill ＆ simulation based hybrid control architecture （S^2BHCA） as the controller＇s design reference was proposed. It is a multi-robot cooperation oriented intelligent control architecture based on hybrid ideas. The S^2BHCA attempts to incorporate the virtues of the reactive controller and of the deliberative controller by introducing the concept of the ＂skill＂. The additional online task simulation ability for cooperation is supported, too. As an application, a multiple AUV control system was developed with three ＂skills＂ for the MCM mission including two different cooperative tasks. The simulation and the sea trials show that simple task expression, fast reaction and better cooperation support can be achieved by realizing the AUV controller based on the S^2BHCA.     

Shape Optimization of Elliptical Road Containers Due to Liquid Load in Steady-State Turning

A numerical analysis of liquid load in elliptical road containers undergoing a steady-state turning manoeuvre is presented for containers of unrestricted size and for containers of fixed capacity. The liquid load is expressed in terms of the horizontal and vertical forces and the overturning moment created by these forces around the middle bottom point of the container. The moment is obtained by integrating the liquid free-surface equation and using numerical calculation of the resulting expressions. An optimization study with an objective to minimize the peak overturning moment is performed on containers of fixed capacity to identify the optimal height/width ratio of the container. The results of this investigation being of a general nature, i.e. with no restriction for an application, are particularly intended for road tankers under a steady turning manoeuvre, where they can be applied with high degree of accuracy.     

Active Roll Control for Passenger Cars

The development of a mathematical model of a limited bandwidth hydro-pneumatic suspension that is incorporated into a vehicle handling model is described. The combined model is used to evaluate a suitable control strategy for eliminating body roll during a cornering manoeuvre. The philosophy behind the roll control strategy has been to use feedback measurements of the body motions which do not compromise the ride control. A study of the influence of the position of the body motion feedback transducer on the effectiveness of the system to reduce the body roll is presented. Non-linear modelling of the suspension components for a 0.8g cornering manoeuvre has revealed performance limitations. Conclusions are drawn as to the effectiveness of the control scheme.     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

Evasive manoeuvres with a steering robot

In the pursuit of an objective rating on vehicle stability performance, it is always desirable to reduce disturbances and inconsistencies during experimental evaluations, especially the ones introduced by human drivers. This paper presents the development of a steering robot designed for closed-loop steering tasks during evasive manoeuvres. It describes the controller structure and discusses experimental results, in addition to simulation/vehicle model verifications and theoretical control analysis.     

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the "Standard for Inland River Navigation" (GB50139-2004) in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouring around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.     

FRP正弦波形夹心桥面板的等效有限元模型

以FRP正弦波形夹心桥面板作为研究对象,得到等效正交各项异性实心板,通过理论分析和数值对比,证明了方法的可行性;采用该法对一实际的FRP正弦波形夹心板桥进行了模态分析。     

电力牵引系统用优化的传动机组

原边能源是电动汽车牵引系统中易造成故障的一个组件,力争对应用了成熟技术的发动机组进行优化.     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

Development of Green-Naghdi models with a wave-absorbing beach for nonlinear, irregular wave propagation

Two-dimensional and three-dimensional Green-Naghdi (GN) models equipped with a numerical wave-absorbing beach have been developed to simulate nonlinear, regular, and irregular wave propagation. The numerical beach is introduced near the downstream boundary to absorb outgoing waves. An appropriate amount of numerical damping and an appropriate length of numerical beach are investigated using numerical experiments. The results show that the GN models with a numerical beach work very well in simulating wave propagation in water in a small computational domain.