Noise level in the vicinity of signalized roundabouts

The analysis, assessment and estimation of noise levels in the vicinity of intersections is a more complex problem than a similar analysis for roads and streets. This is due to the varied geometry of the intersections, differences in the loads of individual movements, participation of heavy vehicles and mass transport vehicles, as well as the various types of traffic management and traffic control. This article analyses the influence of intersection type and traffic characteristics on the noise levels in the vicinity of classic channelized intersections with signalization, roundabouts and signalized roundabouts. Based on the conducted measurements, it has been established that, with comparable traffic parameters and the same distance from the geometric centre of the intersection, the L_Aeq value for signalized roundabouts is 2.5–10.8 dB higher in comparison to classic channelized intersections with signalization and 3.3–6.7 dB higher in relations to the analysed roundabout. Additionally the differences between L_Aeq levels at individual entries at the same signalized roundabouts may reach the value of approximately 4.5 dB. Such situation is influenced by differences in the intersection geometry, diameter of the intersection’s central island, traffic flow type, traffic management at the entries and traffic volume, especially the amount and traffic movements of multiple axle heavy vehicles. These factors have been analysed in detail in relation to signalized roundabouts in this paper.     

The cost of convenience; Air pollution and noise on freeway and arterial light rail station platforms in Los Angeles

Light rail transit (LRT) systems constitute one of the most sustainable public transportation modes and transit agencies have increasingly constructed LRT lines along the median of roadways to reduce land acquisition costs and traffic conflicts. Despite these conveniences, few studies have examined the air pollution and noise exposures for passengers on LRT station platforms within freeway or arterial medians. In response, we monitored particle number count (PNC) concentrations and noise levels on 17 station platforms in the Los Angeles metro system in summer 2012 and assessed differences between freeway and arterial platforms. We visited each station on average 7 times for approximately 19 min with two teams carrying a full set of instruments. As expected, impacts were higher on green line platforms in the center of a grade-separated freeway compared to blue line platforms in the center of an arterial due to being in close proximity to greater traffic volumes. Overall, freeway-arterial platform differences were 35,100 versus 20,000 particles/cm³ for PNC and 83 versus 62 dBA for noise. This average noise intensity on green line platforms was four times that on blue line stations. We also found that PNC concentrations were significantly higher at open air monitoring platform positions compared to standing under a shade canopy (about 2000 particles/cm³ higher), but that noise levels were significantly lower at open air positions compared to under canopy positions (about 3.2 dBA lower). Results identify important factors for transport planners to consider when locating and designing in-roadway LRT platforms.     

On the electrification of road transportation – A review of the environmental,economic, and social performance of electric two-wheelers

Electrification is widely considered as a viable strategy for reducing the oil dependency and environmental impacts of road transportation. In pursuit of this strategy, most attention has been paid to electric cars. However, substantial, yet untapped, potentials could be realized in urban areas through the large-scale introduction of electric two-wheelers. Here, we review the environmental, economic, and social performance of electric two-wheelers, demonstrating that these are generally more energy efficient and less polluting than conventionally-powered motor vehicles. Electric two-wheelers tend to decrease exposure to pollution as their environmental impacts largely result from vehicle production and electricity generation outside of urban areas. Our analysis suggests that the price of e-bikes has been decreasing at a learning rate of 8%. Despite price differentials of 5000 ± 1800 EUR₂₀₁₂ kW h⁻¹ in Europe, e-bikes are penetrating the market because they appear to offer an apparent additional use value relative to bicycles. Mid-size and large electric two-wheelers do not offer such an additional use value compared to their conventional counterparts and constitute niche products at price differentials of 700 ± 360 EUR₂₀₁₂ kW⁻¹ and 160 ± 90 EUR₂₀₁₂ kW⁻¹, respectively. The large-scale adoption of electric two-wheelers can reduce traffic noise and road congestion but may necessitate adaptations of urban infrastructure and safety regulations. A case-specific assessment as part of an integrated urban mobility planning that accounts, e.g., for the local electricity mix, infrastructure characteristics, and mode-shift behavior, should be conducted before drawing conclusions about the sustainability impacts of electric two-wheelers.     

How wide should be the adjacent area to an urban motorway to prevent potential health impacts from traffic emissions?

In recent years, several studies show that people who live, work or attend school near the main roadways have an increased incidence and severity of health problems that may be related with traffic emissions of air pollutants. The concentrations of near-road atmospheric pollutants vary depending on traffic patterns, environmental conditions, topography and the presence of roadside structures. In this study, the vertical and horizontal variation of nitrogen dioxide (NO₂) and benzene (C₆H₆) concentration along a major city ring motorway were analysed. The main goal of this study is to try to establish a distance from this urban motorway considered “safe” concerning the air pollutants human heath limit values and to study the influence of the different forcing factors of the near road air pollutants transport and dispersion. Statistic significant differences (p = 0.001, Kruskal–Wallis test) were observed between sub-domains for NO₂ representing different conditions of traffic emission and pollutants dispersion, but not for C₆H₆ (p = 0.335). Results also suggest significant lower concentrations recorded at 100 m away from roadway than at the roadside for all campaigns (p < 0.016 (NO₂) and p < 0.036 (C₆H₆), Mann–Whitney test). In order to have a “safe” life in homes located near motorways, the outdoor concentrations of NO₂ must not exceed 44–60.0 μg m⁻³ and C₆H₆ must not exceed 1.4–3.3 μg m⁻³. However, at 100 m away from roadway, 81.8% of NO₂ receptors exceed the annual limit value of human health protection (40 μg m⁻³) and at the roadside this value goes up to 95.5%. These findings suggest that the safe distance to an urban motorway roadside should be more at least 100 m. This distance should be further studied before being used as a reference to develop articulated urban mobility and planning policies.     

Evaluating the social cost of cruise ships air emissions in major ports of Greece

Detailed NO_x, SO₂ and PM_2.5 emissions have been estimated for cruise ships in the five busiest Greek ports (i.e. Piraeus, Santorini, Mykonos, Corfu and Katakolo) for year 2013. The emissions were analyzed in terms of gas species, seasonality and activity. The total in-port inventory of cruise shipping accounted to 2742.7 tons: with NO_x being dominant (1887.5 tons), followed by SO₂ and PM_2.5 (760.9 and 94.3 tons respectively). Emissions during hotelling corresponded to 88.5% of total and have significantly outweighed those produced during ships’ maneuvering activities (11.5% of total). Seasonality was found to play a major role, as summer emissions and associated impacts were significantly augmented. The anticipated health impacts of ship emissions can reach to €24.3 million or to €5.3 per passenger proving the necessity of control of the emissions produced by cruise ships in port cities or policy and measures towards a more efficient cruise industry.     

Effects of the 80 km/h and variable speed limits on air pollution in the metropolitan area of barcelona

In 2008 the regional government of Catalonia (Spain) reduced the maximum speed limit on several stretches of congested urban motorway in the Barcelona metropolitan area to 80 km/h, while in 2009 it introduced a variable speed system on other stretches of its metropolitan motorways. We use the differences-in-differences method, which enables a policy impact to be measured under specific conditions, to assess the impact of these policies on emissions of NO_x and PM₁₀. Empirical estimation indicate that reducing the speed limit to 80 km/h causes a 1.7–3.2% increase in NO_x and 5.3–5.9% in PM₁₀. By contrast, the variable speed policy reduced NO_x and PM₁₀ pollution by 7.7–17.1% and 14.5–17.3%. As such, a variable speed policy appears to be a more effective environmental policy than reducing the speed limit to a maximum of 80 km/h.     

Estimation of nitrogen oxides emissions from petrol and diesel passenger cars by means of on-board monitoring: Effect of vehicle speed,vehicle technology,engine type on emission rates

NO_X emission rates of 13 petrol and 3 diesel passenger cars as a function of average speed from 10 to 120 km/h, emission class (pre-Euro 1 – Euro 5), engine type were investigated by on-board monitoring on roads and highways of St. Petersburg using a portative Testo XXL 300 gas analyzer. The highest level of NO_X emission 0.5–2.5 g/km was inherent to old pre-Euro 1 petrol cars without a catalytic converter. NO_X emissions rates of Euro 1 and Euro 2 petrol cars changed within 0.15–0.9 g/km, Euro 3 – 0.015–0.27 g/km, Euro 4 – 0.013–0.1 g/km, Euro 5 – 0.002–0.043 g/km. Euro 3 – Euro 4 petrol cars generally satisfied corresponding NO_X Emission Standards (ES), except cold-start period, Euro 5 petrol cars did not exceed ES. Warmed, stabilized engines of Euro 3 – Euro 5 petrol cars showed 5–10 times lower NO_X emission rates than corresponding ES in the range of speed from 20 to 90 km/h. NO_X emission rates of diesel Euro 3 and Euro 4 cars varied from 0.45 to 1.1 g/km and from 0.31 to 1.1 g/km, respectively. Two examined diesel Euro 3 and one Euro 4 passenger vehicles did not satisfy NO_X ES at real use. Euro 3 diesel cars showed 28.9 times higher NO_X emissions than Euro 3 petrol cars and Euro 4 diesel car demonstrated 17.6 times higher NO_X emissions than Euro 4 petrol cars at warmed and stabilized engine at a cruise speed ranging from 30 to 60 km/h.     

Characteristics of air pollutants at near and far field regions of a national highway located at an industrial complex

This paper presents the characterization of air quality monitored at near field region (NFR) and far field region (FFR) of a national highway located at an industrial complex. The pollutants such as PM₁₀, SO₂ and NO₂ were monitored in two campaigns (11th September to 18th October 2012 and 18th January to 17th February 2013). The 24 h average PM₁₀ concentration at NFR and FFR were found to be 86.69 ± 18.56 μg/m³; 73.16 ± 16.21 μg/m³ and 89.44 ± 18.69 μg/m³; 81.91 ± 16.42 μg/m³, respectively during first and second campaign. In both the campaigns PM₁₀, SO₂ and NO₂ concentration at NFR was higher than FFR. The chemical characterization of PM₁₀ at NFR and FFR indicated the abundance of major elements such as Na (NFR = 30% and FFR = 32%), Ca (NFR = 12% and FFR = 14%) and ions namely NO₃⁻ (NFR = 71% and FFR = 68%) and NH₃⁺ (NFR = 15% and FFR = 19%). Further, at FFR, SO₄²⁻ and NO₃⁻ were found to be 18% and 35% higher than NFR indicating the conversions of SO₂ and NO₂ concentration into secondary particles. The measured SO₂ and NO₂ concentrations were 23 and 21% lower at FFR when compared to NFR confirms the secondary formation.The CALPUFF, EPA regulatory model was set up to understand the dynamics of air pollutants at the industrial complex. The predicted PM₁₀, SO₂ and NO₂ concentrations at NFR and FFR were found to be 32.31 ± 1.56 μg/m³ and 31.35 ± 1.27 μg/m³; 0.37 ± 0.21 μg/m³ and 0.06 ± 0.04 μg/m³; 12.83 ± 6.55 μg/m³ and 4.67 ± 2.77 μg/m³, respectively. The model showed moderate predictions for PM₁₀ (R² = 0.44–0.52), SO₂ (R² = 0.41–0.51) and NO₂ (R² = 0.45–0.61) concentrations.     

Capitalization of BRT network expansions effects into prices of non-expansion areas

A before and after hedonic model is used to determine the property value impacts on properties already served by the transit system caused by extensions to Bogotá’s bus rapid transit system. Asking prices of residential properties belonging to an intervention area (N = 1407 before, 1570 after) or a control area (N = 267 before, 732 after) and offered for sale between 2001 and 2006 are used to determine capitalization of the enhanced regional access provided by the extension. Properties offered during the year the extension was inaugurated and in subsequent years have asking prices that are between 13% and 14% higher than prices for properties in the control area, after adjusting for structural, neighborhood and regional accessibility characteristics of each property. Furthermore, the appreciation is similar for properties within 500 m and properties between 500 m and 1 km of the BRT.     

Effects of battery chemistry and performance on the life cycle greenhouse gas intensity of electric mobility

Lithium traction batteries are a key enabling technology for plug-in electric vehicles (PEVs). Traction battery manufacture contributes to vehicle production emissions, and battery performance can have significant effects on life cycle greenhouse gas (GHG) emissions for PEVs. To assess emissions from PEVs, a life cycle perspective that accounts for vehicle production and operation is needed. However, the contribution of batteries to life cycle emissions hinge on a number of factors that are largely absent from previous analyses, notably the interaction of battery chemistry alternatives and the number of electric vehicle kilometers of travel (e-VKT) delivered by a battery. We compare life cycle GHG emissions from lithium-based traction batteries for vehicles using a probabilistic approach based on 24 hypothetical vehicles modeled on the current US market. We simulate life-cycle emissions for five commercial lithium chemistries. Examining these chemistries leads to estimates of emissions from battery production of 194–494 kg CO₂ equivalent (CO₂e) per kWh of battery capacity. Combined battery production and fuel cycle emissions intensity for plug-in hybrid electric vehicles is 226–386 g CO₂e/e-VKT, and for all-electric vehicles 148–254 g CO₂e/e-VKT. This compares to emissions for vehicle operation alone of 140–244 g CO₂e/e-VKT for grid-charged electric vehicles. Emissions estimates are highly dependent on the emissions intensity of the operating grid, but other upstream factors including material production emissions, and operating conditions including battery cycle life and climate, also affect life cycle GHG performance. Overall, we find battery production is 5–15% of vehicle operation GHG emissions on an e-VKT basis.     

Guidance for new policy developments on railway noise and vibration

Noise and vibration are two of the main problems associated with railways in residential areas. To ensure quality of life and well-being of inhabitants living in the vicinity of railway paths, it is important to evaluate, understand, control and regulate railway noise and vibration. Much attention has been focused on the impact of noise from railway traffic but the consideration of railway-induced vibration has often been neglected. This paper aims to provide policy guidance based on results obtained from the analyses of relationships estimated from ordinal logit models between human response, railway noise exposure and railway vibration exposure. This was achieved using data from case studies comprised of face-to-face interviews (N = 931), internal vibration measurements (N = 755), and noise calculations (N = 688) collected within the study “Human Response to Vibration in Residential Environments” by the University of Salford, UK. Firstly, the implications of neglecting vibration in railway noise policies are investigated. The findings suggest that it is important to account for railway induced vibrations in future noise and transport policies, as neglecting vibrations results in an underestimation of people highly annoyed by noise. Secondly, implications of neglecting different types of railway sources are presented. It was found that the impact of noise and vibration form maintenance operations should be better understood and should be taken into account when assessing the environmental impact of railways in residential environments. Finally, factors that were found to influence railway vibration annoyance are presented and expressed as weightings. The data shows that factors specific to a particular residential area should also be taken into account in future vibration policies as the literature shows that attitudinal, socio-demographic and situational factors have a large influence on vibration annoyance responses. This work will be of interest to researchers and environmental health practitioners involved in the assessment of vibration complaints, as well as to policy makers, planners and consultants involved in the design of buildings and railways.     

An environmental assessment of air traffic speed constraints in the departure phase of flight: A case study at Gothenburg Landvetter Airport,Sweden

This paper considers the environmental effects of air traffic management speed constraints during the departure phase of flight. We present a CO₂ versus noise trade-off study that compares aircraft departure procedures subject to speed constraints with a free speed scenario. A departure route at Gothenburg Landvetter Airport in Sweden is used as a case study and the analysis is based on airline flight recorded data extracted from the Airbus A321 aircraft. Results suggest that CO₂ emissions could be reduced by 180 kg per flight if all departure speed constraints were removed at a cost of increased noise exposure below 70 dB(A).     

Measuring transport related CO2 emissions induced by online and brick-and-mortar retailing

We develop a method for empirically measuring the difference in transport related carbon footprint between traditional and online retailing (“e-tailing”) from entry point to a geographical area to consumer residence. The method only requires data on the locations of brick-and-mortar stores, online delivery points, and residences of the region’s population, and on the goods transportation networks in the studied region. Such data are readily available in most countries. The method has been evaluated using data from the Dalecarlia region in Sweden, and is shown to be robust to all assumptions made. In our empirical example, the results indicate that the average distance from consumer residence to a brick-and-mortar retailer is 48.54 km in the studied region, while the average distance to an online delivery point is 6.7 km. The results also indicate that e-tailing increases the average distance traveled from the regional entry point to the delivery point from 47.15 km for a brick-and-mortar store to 122.75 km for the online delivery points. However, as professional carriers transport the products in bulk to stores or online delivery points, which is more efficient than consumers’ transporting the products to their residences, the results indicate that consumers switching from traditional to e-tailing on average reduce their transport CO₂ footprints by 84% when buying standard consumer electronics products.     

Commuters’ exposure to PM2.5 and CO2 in metro carriages of Shanghai metro system

Air quality inside transportation carriages has become a public concern. A comprehensive measurement campaign was conducted to examine the commuters’ exposure to PM_2.5 (d_p ⩽ 2.5 μm) and CO₂ in Shanghai metro system under different conditions. The PM_2.5 and CO₂ concentrations inside all the measured metro lines were observed at 84 ± 42 μg/m³ and 1253.1 ± 449.1 ppm, respectively. The factors that determine the in-carriage PM_2.5 and CO₂ concentrations were quantitatively investigated. The metro in-carriage PM_2.5 concentrations were significantly affected by the ventilation systems, out-carriage PM_2.5 concentrations and the passenger numbers. The largest in-carriage PM_2.5 and CO₂ concentrations were observed at 132 μg/m³ and 1855.0 ppm inside the carriages equipped with the oldest ventilation systems. The average PM_2.5 and CO₂ concentrations increased by 24.14% and 9.93% as the metro was driven from underground to overground. The average in-carriage PM_2.5 concentrations increased by 17.19% and CO₂ concentration decreased by 16.97% as the metro was driven from urban to the suburban area. It was found that PM_2.5 concentration is proportional to the on-board passenger number at a ratio of 0.4 μg/m³·passenger. A mass-balance model was developed to estimate the in-carriage PM_2.5 concentration under different driving conditions.     

Isocyanic acid and ammonia in vehicle emissions

Vehicles are considered to be an important source of ammonia (NH₃) and isocyanic acid (HNCO). HNCO and NH₃ have been shown to be toxic compounds. Moreover, NH₃ is also a precursor in the formation of atmospheric secondary aerosols. For that reason, real-time vehicular emissions from a series of Euro 5 and Euro 6 light-duty vehicles, including spark ignition (gasoline and flex-fuel), compression ignition (diesel) and a plug-in electric hybrid, were investigated at 23 and −7 °C over the new World harmonized Light-duty vehicle Test Cycle (WLTC) in the Vehicle Emission Laboratory at the European Commission Joint Research Centre Ispra, Italy. The median HNCO emissions obtained for the studied fleet over the WLTC were 1.4 mg km⁻¹ at 23 °C and 6 mg km⁻¹ at −7 °C. The fleet median NH₃ emission factors were 10 mg km⁻¹ and 21 mg km⁻¹ at 23 and −7 °C, respectively. The obtained results show that even though three-way catalyst (TWC), selective catalytic reduction (SCR), and NOx storage catalyst (NSC) are effective systems to reduce NOx vehicular emissions, they also lead to considerable emissions of the byproducts NH₃ and/or HNCO. It is also shown that diesel light-duty vehicles equipped with SCR can present NH₃ emission factors as high as gasoline light-duty vehicles at both, 23 and −7 °C over the WLTC. Therefore, with the introduction in the market of this DeNOx technology, vehicular NH₃ emissions will increase further.     

Preliminary investigation of PM1, PM2.5, PM10 and its metal elemental composition in tunnels at a subway station in Shanghai,China

In this study, real-time monitoring campaigns were conducted in two tunnels (Line A and Line B) at a subway station in Shanghai, including temperature, relative humidity, PM₁, PM_2.5 and PM₁₀, in order to understand the climate and PM characteristics in the transportation microenvironment. In addition, collected floor dust particles in the tunnel were analyzed by ICP for their metal elemental composition. Strong correlations occurred between all PM levels and meteorological parameters in the tunnel of Line A (with platform screen doors), in comparison with the weak correlations between such parameters in the tunnel of Line B (without platform screen doors). PM_2.5 and PM₁₀ between peak hours and off-peak hours for both lines presented significant differences (p < 0.05), respectively. Nevertheless, PM₁ showed a different pattern, with p > 0.05 for Line A and p < 0.05 for Line B, respectively. In addition, statistical results concluded that PM had an evident weekly variation for both lines. Friday was the highest day of all particulate matters in monitoring periods for both lines. Ratios of PM₁/PM₁₀ and PM_2.5/PM₁₀ were high when trains were out of service and low when trains were in service. Relative abundance of metal elements detected from floor dust particles proved that floor dust particles in tunnels might be a major source of airborne PM in the subway microenvironments, with Fe as the most abundant metal element, followed by Ca, Al, Mg, Mn, Zn, Cu, Cr, Ni, Pb and Hg.     

Ultrafine particle infiltration into passenger vehicles. Part II: Model analysis

Experimental studies showed that infiltration and passive ventilation are important air exchange mechanisms inside vehicles but previous mathematical models did not consider either one. In this study, we incorporated infiltration and passive ventilation to advance the existing mathematical models and evaluated how different transport mechanisms affect passenger exposures at increasing speeds. Infiltration was formulated using Bernoulli’s equation and passive ventilation was derived empirically. The new model describes ultrafine particle (UFP) and carbon dioxide (CO₂) transport for a wide range of driving speed under any ventilation conditions. Unlike statistical models, this mathematical model can also provide vehicle-specific and transport mechanism-specific information. The model predictions were in a good agreement with data collected from 10 different vehicle models with an average discrepancy of less than 16% for UFPs and less than 3% for CO₂. Under outdoor air (OA) mode, when the fan is off, the model simulation showed that the infiltration and passive ventilation can substantially increase the UFP I/O (in-cabin/on-road concentrations) ratio from 0.15 at 0 km/h to 0.57 at 130 km/h. At medium fan setting, mechanical ventilation dominates and UFP I/O stays at 0.58 regardless of driving speed. Under recirculation (RC) mode, infiltration increases and the RC-mode filtration only removed 44% and 69% of the infiltrated particles at the lowest and medium fan settings, respectively. Model simulations under OA mode show that infiltration starts to occur above 115 km/h with the lowest fan setting; whereas, medium and higher fan settings prevent infiltration up to 145 km/h.     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

Performance and emission characteristics of a spark ignition engine fuelled with butanol isomer-gasoline blends

The heavy reliance on petroleum-derived fuels such as gasoline in the transportation sector is one of the major causes of environmental pollution. For this reason, there is a critical need to develop cleaner alternative fuels. Butanol is an alcohol with four different isomers that can be blended with gasoline to produce cleaner alternative fuels because of their favourable physicochemical properties compared to ethanol. This study examined the effect of butanol isomer-gasoline blends on the performance and emission characteristics of a spark ignition engine. The butanol isomers; n-butanol, sec-butanol, tert-butanol and isobutanol are mixed with pure gasoline at a volume fraction of 20 vol%, and the physicochemical properties of these blends are measured. Tests are conducted on a SI engine at full throttle condition within an engine speed range of 1000–5000 rpm. The results show that there is a significant increase in the engine torque, brake power, brake specific fuel consumption and CO₂ emissions with respect to those for pure gasoline. The butanol isomers-gasoline blends give slightly higher brake thermal efficiency and exhaust gas temperature than pure gasoline at higher engine speeds. The iBu20 blend (20 vol% of isobutanol in gasoline) gives the highest engine torque, brake power and brake thermal efficiency among all of the blends tested in this study. The isobutanol and n-butanol blend results in the lowest CO and HC emissions, respectively. In addition, all of the butanol isomer-gasoline blends yield lower NO emissions except for the isobutanol-gasoline blend.