两相流相互作用下的船模微气泡减阻性能数值仿真

基于两相流理论,对集装箱船船模进行微气泡减阻性能数值仿真研究。分析船模在不同喷气口位置、流体含气率、不同喷射速度和角度下的流场分布和减阻效果。结果表明：当流体微气泡含量过高时,会增大船体摩擦阻力,流体含气率为10%~20%时,有较好的减阻效果,喷气口位置在距离球鼻艏后缘约三分之一船长附近具有较高的空气覆盖率,喷气口喷气方向垂直向下所产生的减阻效果比喷气方向偏向船侧效果要好,且船速较高时可允许较高含气率流体注入流场并增大减阻效果。     

采用微气泡缩减高速船拖曳阻力(英文)

Ship hull form of the underwater area strongly influences the resistance of the ship.The major factor in ship resistance is skin friction resistance.Bulbous bows,polymer paint,water repellent paint(highly water-repellent wall),air injection,and specific roughness have been used by researchers as an attempt to obtain the resistance reduction and operation efficiency of ships.Micro-bubble injection is a promising technique for lowering frictional resistance.The injected air bubbles are supposed to somehow modify the energy inside the turbulent boundary layer and thereby lower the skin friction.The purpose of this study was to identify the effect of injected micro bubbles on a navy fast patrol boat(FPB) 57 m type model with the following main dimensions:L=2 450 mm,B=400 mm,and T=190 mm.The influence of the location of micro bubble injection and bubble velocity was also investigated.The ship model was pulled by an electric motor whose speed could be varied and adjusted.The ship model resistance was precisely measured by a load cell transducer.Comparison of ship resistance with and without micro-bubble injection was shown on a graph as a function of the drag coefficient and Froude number.It was shown that micro bubble injection behind the mid-ship is the best location to achieve the most effective drag reduction,and the drag reduction caused by the micro-bubbles can reach 6%-9%.     

Ship resistance of quadramaran with various hull position configurations

Multihull ships are widely used for sea transportation, and those with four hulls are known as quadramarans. Hull position configurations of a quadramaran include the diamond, tetra, and slice. In general, multihull vessels traveling at high speeds have better hydrodynamic efficiency than monohull ships. This study aims to identify possible effects of various quadramaran hull position configurations on ship resistance for hull dimensions of 2 m length, 0.21 m breadth, and 0.045 m thickness. We conducted a towing test in which we varied the hull spacing and speed at Fr values between 0.08 and 0.62 and measured the total resistance using a load cell transducer. The experimental results reveal that the lowest total resistance was achieved with a diamond quadramaran configuration at Fr = 0.1-0.6 and an effective interference factor of up to 0.35 with S/L = 3/10 and R/L = 1/2 at Fr = 0.62.     

基于Fluent的船体界面阻力分析

基于 Fluent对船体界面阻力进行仿真分析,采用 VOF的方法模拟船体在空气和水两相中的运动情况,获得不同航速下船体摩擦阻力和压差阻力的关系。考虑方型系数对于船体阻力的影响,建立多个方型系数不同的模型来实现Fluent仿真模拟,获得一定傅汝德数下船体方形系数与船体阻力的关系,得到船舶阻力相对优化的船型。该方法通过更加精确的建模可为船体型线减阻提供更多的依据。     

Resistance analysis of unsymmetrical trimaran model with outboard sidehulls configuration

The application of multi-hull ship or trimaran vessel as a mode of transports in both river and sea environments have grown rapidly in recent years.Trimaran vessels are currently of interest for many new high speed ship projects due to the high levels of hydrodynamic efficiency that can be achieved,compared to the mono-hull and catamaran hull forms.The purpose of this study is to identify the possible effects of using an unsymmetrical trimaran ship model with configuration（S/L） 0.1-0.3 and R/L=0.1-0.2.Unsymmetrical trimaran ship model with main dimensions： L=2000mm,B=200 mm and T=45 mm.Experimental methods（towing tank） were performed in the study using speed variations at Froude number 0.1-0.6.The ship model was pulled by an electric motor whose speed could be varied and adjusted.The ship model resistance was measured precisely by using a load cell transducer.The comparison of ship resistance for each configuration with mono-hull was shown on the graph as a function of the total resistance coefficient and Froude number.The test results found that the effective drag reduction could be achieved up to 17% at Fr=0.35 with configuration S/L=0.1.     

平头方尾运输船舶开槽减阻研究

传统的平头方尾型运输船舶具有载重大、吃水浅的优点,但航行阻力大,航速低。本文针对该船型开展了开槽减阻的研究,通过在船底开设纵向槽道对艏部高压区进行引流减阻,来实现该船型高航速运输的要求。船体流场及阻力采用RANS方法进行数值模拟,并计及航行姿态的变化。通过改变槽道长度、宽度以及槽道顶板的形状,研究了减阻效果与槽道几何尺度的关系。针对某型船船的研究表明,船底槽道的引流量是影响减阻效果的主要因素,当采用纵向贯穿的槽道,且槽道顶板的折角点设在船中时,可使原船30节时的减阻率达到24%以上。     

超大型集装箱船能效设计指数优化研究

采用船型优化方法就超大型集装箱船10 000TEU的能效设计指数(EEDI)进行优化.文中以降低对主机功率的需求、提高能效设计水平为目标,优化该超大型集装箱船的阻力性能.优化时利用平移法和径向基函数方法进行船体曲面重构,并分别采用基于Rankine源非线性势流理论和边界层动量积分计算兴波阻力和摩擦阻力,最后同时使用遗传算法(NSGA-Ⅱ)和序列二次规划算法(NLPQL)在设计空间中探索满足约束条件的阻力最优船型.结果表明,通过该优化方法获得的最优船型,其能效设计指数优化程度明显,能够满足现阶段IMO对新造集装箱船计及折减系数后的强制要求.     

Resistance analysis of a semi-SWATH design concept in shallow water

Resistance analysis is an important analytical method used to evaluate the hydrodynamic performance of High Speed Craft (HSC). Analysis of multihull resistance in shallow water is essential to the performance evaluation of any type of HSC. Ships operating in shallow water experience increases in resistance because of changes in pressure distribution and wave pattern. In this paper, the shallow water performance of an HSC design concept, the semi-Small Waterplane Area Twin Hull (semi-SWATH) form, is studied. The hull is installed with fin stabilizers to reduce dynamic motion effects, and the resistance components of the hull, hull trim condition, and maximum wave amplitude around the hull are determined via calm water resistance tests in shallow water. These criteria are important in analyzing semi-SWATH resistance in shallow water and its relation to flow around hull. The fore fin angle is fixed to zero degrees, while the aft fin angle is varied to 0°, 5°, 10°, and 15°. For each configuration, investigations are conducted with depth Froude numbers (Fr _H ) ranging from 0.65 to 1.2, and the resistance tests are performed in shallow water at the towing tank of UTM. Analysis results indicate that the resistance, wave pattern, and trim of the semi-SWATH hull form are affected by the fin angle. The resistance is amplified whereas the trim and sinkage are reduced as the fin angle increases. Increases in fin angle contribute to seakeeping and stability but affect the hull resistance of HSCs.     

滑行艇气层减阻试验

通过对三种艇型及不同的喷气方式的模型试验，研究了断阶滑行艇模型气层减阻的实施途径及减阻效果，取得了总阻力减少25％以上 结果，提出了一种适合于采用气层减阻技术且阻力性能优良的艇型。垂向舭板可减少滑行艇的高速阻力，但阻力减少的程度与艇型有关。底部斜升角较小时，有利于气层减阻。气层减阻率大于舭板减阻率，对底部斜升角较大且艇底扭曲、艏部设置适当的纵向防溅条、舯部设置楔形板的深Ⅴ型艇，垂向舭板对其阻力的影响不大，这种深Ⅴ型艇的阻力性能较佳，若喷气，其总阻力还可进一步减少15％。孔喷时，孔径采0.5mm或1.3mm对模型阻力的影响甚微，采用0.4mm缝叶的模型阻力比用孔喷时略大，采用较大孔喷或缝喷有利于工程上的喷气实施。     

Determining the Scour Dimensions Around Submerged Vanes in a 180° Bend with the Gene Expression Programming Technique

Submerged vanes are installed on rivers and channel beds to protect the outer bank bends from scouring. Also, local scouring occurs around the submerged vanes over time, and identifying the effective factors on the scouring phenomena around these submerged vanes is one of the important issues in river engineering. The most important aim of this study is investigation of scour pattern around submerged vanes located in 180° bend experimentally and numerically. Firstly, the effects of various parameters such as the Froude number (Fr), angle of submerged vanes to the flow (α), angle of submerged vane location in the bend (θ), distance between submerged vanes (d), height (H), and length (L) of the vanes on the dimensionless volume of the scour hole were experimentally studied. The submerged vanes were installed on a 180° bend whose central radius and channel width were 2.8 and 0.6 m, respectively. By reducing the Froude number, the scour hole volume decreased. For all Froude numbers, the biggest scour hole formed at θ?=?15°. In all models, by increasing the Froude number, the scour hole volume significantly increases. In addition, by increasing the submerged vanes’ length and height, the scour hole dimensions also grow. Secondly, using gene expression programming (GEP), a relationship for determining the scour hole volume around the submerged vanes was provided. For this model, the determination coefficients (R²) for the training and test modes were computed as 0.91 and 0.9, respectively. In addition, this study performed partial derivative sensitivity analysis (PDSA). According to the results, the PDSA was calculated as positive for all input variables.     

大型半潜船球首设计及阻力性能对比分析

在船速较低的肥大型船舶上，安装球鼻艏会在很大程度上降低船舶受到的阻力，球艏对艏部型线有缓和的作用,使船舶艏部水流发生改变,减少艏底漩涡,从而降低形状阻力，进而改善船舶的水动力性能。根据设计的10万吨级半潜船船型的船模静水阻力试验情况，该船舶船首由直立型改为球鼻艏型式，通过对原型和改进后的船型的阻力试验结果进行对比，检验了新船型的减阻性能，同时对船尾伴流场进行了研究，发现船首形状改变对尾部半流场影响不大     

半滑行船扰流板阻力试验研究

半滑行船的航行姿态对船体阻力影响较大。为研究扰流板对半滑行船的降阻作用,首先在3种典型载况下,确定了船模未加扰流板的阻力、纵倾及升沉;然后在这3种载况下,于船模艉部添加扰流板,与静水未添加扰流板时船模的阻力和航态作比较,且不同航速时扰流板的设置不同。实验结果表明:合理的扰流板高度可以减小半滑行船的纵倾角和阻力;扰流板的降阻效果与船模的压载有关,其中满载情况下的降阻效果最为明显,最大可达6%。     

Added resistance acting on hull of a non ballast water ship

In this paper, added resistances acting on a hull of non ballast water ship(NBS) in high waves is discussed. The non ballast water ships were developed at the laboratory of the authors at Osaka Prefecture University, Japan. In the present paper, the performances of three kinds of bow shapes developed for the NBS were theoretically and experimentally investigated to find the best one in high waves. In previous papers, an optimum bow shape for the NBS was developed in calm water and in moderated waves. For a 2 m model for experiments and computations, the wave height is 0.02 m. This means that the wave height is 15% of the draft of the ship in full load conditions. In this paper, added resistances in high waves up to 0.07 m for a 2 m model or 53% of the full load draft are investigated. In such high waves linear wave theories which have been used in the design stage of a ship for a long time may not work well anymore, and experiments are the only effective tool to predict the added resistance in high waves. With the computations for waves, the ship is in a fully captured condition because shorter waves, λ/Lpp0.6, are assumed.     

船体艏部水动力性能优化

提出一种以势流兴波阻力理论Rankine源方法为基础,结合SHIPFLOW软件为计算工具,利用CAD-CFD集成平台FRIENDSHIP-Framework软件进行变形优化,研究船舶的最小兴波阻力型线优化设计的方法,并考察了兴波优化得到的船型总阻力变化情况。在型线优化过程中,以兴波阻力系数为目标函数,排水量变化范围为约束条件,在Wigley船体前端增加一个利用Feature建模技术参数化生成的球艏并调整艏部型线使得船体表面光顺。选取球鼻艏形状的各项参数作为基本设计变量,利用DOE方法对船艏进行优化,获得了设计航速下兴波阻力较小的船型,验证了所提方法进行船艏型线优化的有效性。相应的考察变形及优化前后总阻力变化情况表明:在高傅汝德数情况下增加球艏所带来的粘性阻力的增加小于兴波阻力的减小量,总阻力得到了改善,优化后得到的球艏能在进一步减小兴波的同时减小总阻力。此外,还运用所提方法对3100TEU船型的船艏,利用Delta Shift方法进行变形,在设计航速下,将变形的参数作为设计变量,利用DOE方法进行优化设计。结果显示:在排水量限制范围内当球鼻艏向上向前伸展一定长度时可以降低兴波阻力。与此同时,由于优化前后船体湿表面积变化很小,粘性阻力的变化并不明显,兴波的减小则使得总阻力得到了改善。     

Simulators in bridge operations training and assessment: a systematic review and qualitative synthesis

This article presents a systematic review and qualitative synthesis of the use of simulators in maritime education and training (MET), with a focus on bridge operations during navigation training and assessment. The review found 34 articles published in a wide range of academic journals, displaying a global field of research consisting of three main disciplines: Maritime professionals (n = 15), Human factors (n = 13) and Education (n = 6). An important conclusion made after synthesising the results of the studies is that while the potential of using simulators in training and assessment are clear, little is known about which instructional practices would ensure valid and reliable results of simulator-based education. Since MET institutions train their students for one of the most safety-critical industries in the world, there is a need for empirical studies that explore the use of simulator-based training and assessment further to lay the foundation for an evidence-based educational practice.     

船用梯形微沟槽表面减阻效应的仿真分析与实验验证

基于微沟槽减阻机理,采用改变船体表面微结构形貌尺寸的方法,以期降低船舶运行中的航行阻力,提高船舶航行效率,节约能源。利用流体软件FLUENT对梯形肋条和梯形沟槽两种微结构表面流场进行模拟仿真,分析了沟槽深宽比h/d1的减阻效果。仿真结果表明,对于梯形肋条,在h/d1时均具有减阻效果,当h/d为0.45时减阻效果最好;对于梯形沟槽,当h/d为0.30、0.36时表现为增阻,h/d为0.45、0.60、0.75时表现为减阻,其中当h/d为0.60时的减阻效果最好。为了验证模拟计算的规律,进行了阻力冲刷实验,实验结果与模拟计算结果的对比分析表明模拟计算与实验结论一致。     

改进Sobol’方法在船型优化模型中的应用

针对船型优化中采用更多的优化变量有可能带来"维度灾难"的问题,通过灵敏度分析确定不重要的变量并降维来缓解该问题。介绍以往提出的改进Sobol’方法,利用该方法对某集装箱船兴波阻力优化模型进行灵敏度分析并降维。为减少分析的计算量,对该船型优化模型构建Kriging模型。对优化模型降维前后的优化过程、最优解及其波形和型线进行对比。结果表明:降维后优化模型收敛更快,最优解兴波阻力系数仅增大0.15%,采用改进Sobol’方法进行降维,能在保证最优解质量的同时,提高优化效率。     

Experimental study on microbubble ejection method for frictional drag reduction

The formation of air bubbles ejected through a single hole in a flat plate was observed in uniform flow of 2–10 m/s It was confirmed that the size of the air bubbles was governed by main flow velocity and air flow rate. According to previous experiments, the size of the bubbles is an important factor in frictional drag reduction by microbubble ejection. Usually bubbles larger than a certain diameter (for example 1 mm) have no effect on frictional drag reduction. Three different methods were proposed and tested to generate smaller bubbles. Among them, a 2D convex (half body of an NACA 64-021 section) with ejection holes at the top was the best and most promising. The diameter of the bubbles became about one-third the size of the reference ejection on a flat plate. Moreover, the bubble size did not increase with increasing flow rate. This is a favorable characteristic for practical purposes. The skin friction force was measured directly with a miniature floating element transducer, and decreased drastically by microbubble ejection from the top of the 2D convex shape.     

CFD-based method of determining form factor <Emphasis Type="Italic">k</Emphasis> for different ship types and different drafts

The value of form factor k at different drafts is important in predicting full-scale total resistance and speed for different types of ships. In the ITTC community, most organizations predict form factor k using a low-speed model test. However, this method is problematic for ships with bulbous bows and transom. In this article, a Computational Fluid Dynamics (CFD)-based method is introduced to obtain k for different type of ships at different drafts, and a comparison is made between the CFD method and the model test. The results show that the CFD method produces reasonable k values. A grid generating method and turbulence model are briefly discussed in the context of obtaining a consistent k using CFD.     

考虑航行姿态变化的的高速船阻力性能预报

为了精确获得高速船的航行阻力,计及航行姿态变化对其阻力的影响。基于CFD理论,本文通过耦合求解计及黏性的RANS和船体运动方程的方式实时预报船体受力,船体根据受力进行姿态调整,最终达到平衡,以此预报船舶在高速运动稳定后的航行姿态及阻力。并将一系列的数值计算结果与试验数据对比分析,数值计算结果和实验数据吻合良好。船舶设计工作者可以参考数值计算结果辅助船体型线设计,其具有重要的工程应用价值。