控制和管理一体化的DCS系统

阐述工业控制和管理一体化ＤＣＳ系统的重要性，介绍了一种网桥，将２＋控制网和ＮＯＶＥＬＬ网连网，并给出了具体的系统图和接口电路图。     

电机悬挂方式对LIM地铁系统动力特性的影响研究

研究目的：研究直线电机地铁在不同电机悬挂方式下的气隙变化规律及车辆、轨道的动力响应特性，并将二者进行比较。研究方法：应用车辆轨道耦合动力学理论，分别建立不同悬挂方式下的系统模型并编制相应的仿真程序，通过在轨道局部加入谐波型余弦不平顺激励对系统的动力特性进行分析。研究结果：2种悬挂方式对系统的各向加速度和轮轨力的影响差别较小，而气隙变化呈现明显不同的规律。研究结论：直线电机采用架悬式悬挂时，要严格控制幅值大于5．5mm的长波不平顺，防止电机和反力板之问的刮蹭；而当采用抱轴式悬挂时，要注意控制大幅值的短波不平顺出现，防止气隙过大，影响电机效率。     

预裂爆破中爆生裂缝扩展的机理探讨及预裂炮孔间距的设计方法

炸药爆炸产生的爆生裂缝是由爆炸应力波和爆生气体共同作用的结果。文中运用炸药爆炸的应力波理论,计算初始裂纹的长度;然后按照岩石的脆断理论计算爆生裂缝的最终扩展长度,对预裂爆破中爆炸作用过程和裂缝的扩展机理进行分析。同时还讨论了预裂炮孔间距的设计方法,认为在炮孔间距设计时,应考虑原生裂缝的存在。     

两次定位法船体总段大合拢

对中小型船舶建造中常用的船体总段大合拢方法,包括合拢前的工艺准备、合拢的工艺过程、防变形手段和质量控制以及环形焊缝的焊接等作了全面论述,提出在大接头焊接缝加马板;加放焊缝横向收缩补偿量等控制变形的具体措施。     

论港口建设工程造价的全过程管理

港口建设工程造价的控制与管理是一个动态的过程,文中重点分析了在项目投资决策阶段、项目设计阶段、项目实施阶段和竣工阶段全过程造价管理的方法与侧重点,以提高投资效益。     

光学仪器法快速找寻轴系理论中心线的研究

舰船轴系装调过程中,理论中心线的确定方法有多种。本文采用光学仪器法快速找寻轴系理论中心线,理论支持性强,高效而独特,具有较强的实用性。     

"公交优先"大环境下的城市公交客车市场发展趋势

针对我国目前城市公交的特点及现阶段存在的主要问题,对国家“公交优先”的政策进行解读,并对“公交优先”环境下城市公交客车市场的发展趋势进行预测。     

土工格栅在治理沥青路面裂缝中的应用

裂缝是沥青路面常见病害。应用非织造土工织物——多功能双向土工格栅治理高等级公路沥青路面的裂缝,取得了良好的效果,并对土工格栅的应用进行了定量计算。     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the "Standard for Inland River Navigation" (GB50139-2004) in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouring around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.